The ECM constantly generates a 5 V power source voltage from the battery voltage supplied to the +B, +B2 (BATT) terminals to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.
When the VC circuit has a short circuit, the microprocessor in the ECM and sensors that are supplied power through the VC circuit are deactivated because power is not supplied from the VC circuit. When the system is in this condition, it will not start.
For the circuit diagram of the ECM power source refer to the ECM power source circuit.
Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>ECM Power Source Circuit
VC Output Circuit
Check the fuses for circuits related to this system before performing the following inspection procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
| *1 | No. 1 Engine Room Relay Block and Junction Block Assembly |
| *2 | EFI NO. 1 Fuse |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (EFI NO. 1 fuse) - Body ground | Ignition switch ON | 11 to 14 V |
Check the fuse with it installed to the No. 1 engine room relay block and junction block assembly.
If the result is not as specified, since current is not flowing to the +B and +B2 terminals of the ECM, the system may not be started.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the throttle body with motor assembly connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
Perform "Inspection After Repair" after replacing the throttle body with motor assembly.
Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
A
B
Disconnect the accelerator pedal sensor assembly connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the crankshaft position sensor connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the camshaft position sensor (for intake camshaft) connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the manifold absolute pressure sensor connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the camshaft position sensor (for exhaust camshaft) connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the engine oil pressure and temperature sensor connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the fuel pressure sensor (for high pressure side) connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
Perform "Inspection After Repair" after replacing the fuel pressure sensor (for high pressure side).
Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
A
B
Disconnect the fuel pressure sensor (for low pressure side) connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible (w/ Gasoline Particulate Filter) | A |
| Communication is not possible (w/o Gasoline Particulate Filter) | B |
| Communication is possible | C |
Perform "Inspection After Repair" after replacing the fuel pressure sensor (for low pressure side).
Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
A
B
C
Disconnect the differential pressure sensor connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Click hereEngine / Hybrid System>M20A-FKS (EMISSION CONTROL)>DIFFERENTIAL PRESSURE SENSOR(w/ GPF)>REMOVAL
Disconnect the mass air flow meter sub-assembly connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible (for continuously variable transaxle models) | A |
| Communication is not possible (for manual transaxle models) | B |
| Communication is possible | C |
Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.
Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
A
B
C
Disconnect the clutch stroke sensor connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible (w/ Stop and Start System) | A |
| Communication is not possible (w/o Stop and Start System) | B |
| Communication is possible | C |
A
B
C
for LHD: Click hereDrivetrain>CLUTCH>CLUTCH STROKE SENSOR (for LHD)>REMOVAL
for RHD: Click hereDrivetrain>CLUTCH>CLUTCH STROKE SENSOR (for RHD)>REMOVAL
Disconnect the neutral position switch connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
for 2WD: Click hereDrivetrain>EG62 (MANUAL TRANSMISSION / TRANSAXLE)>NEUTRAL POSITION SWITCH>REMOVAL
for 4WD/AWD: Click hereDrivetrain>EG62F (MANUAL TRANSMISSION / TRANSAXLE)>NEUTRAL POSITION SWITCH>REMOVAL
Disconnect the throttle body with motor assembly connector.
Disconnect the crankshaft position sensor connector.
Disconnect the camshaft position sensor (for intake camshaft) connector.
Disconnect the camshaft position sensor (for exhaust camshaft) connector.
Disconnect the manifold absolute pressure sensor connector.
Disconnect the engine oil pressure and temperature sensor connector.
Disconnect the accelerator pedal sensor assembly connector.
Disconnect the mass air flow meter sub-assembly connector.
Disconnect the fuel pressure sensor (for high pressure side) connector.
Disconnect the fuel pressure sensor (for low pressure side) connector.
Disconnect the clutch stroke sensor connector (for manual transaxle models).
Disconnect the neutral position switch connector (w/o stop and start system for manual transaxle models).
Disconnect the differential pressure sensor connector. (w/ Gasoline Particulate Filter)
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C40-109 (VCTA) - Body ground | Always | 10 kΩ or higher |
| C40-116 (VCNE) - Body ground | Always | 10 kΩ or higher |
| C40-88 (VCV1) - Body ground | Always | 10 kΩ or higher |
| C40-113 (VCE1) - Body ground | Always | 10 kΩ or higher |
| C40-121 (VCPM) - Body ground | Always | 10 kΩ or higher |
| C40-99 (VCPE) - Body ground | Always | 10 kΩ or higher |
| A24-57 (VCPA) - Body ground | Always | 10 kΩ or higher |
| A24-60 (VCP2) - Body ground | Always | 10 kΩ or higher |
| C40-78 (VCVG) - Body ground | Always | 10 kΩ or higher |
| C40-98 (VCPR) - Body ground | Always | 10 kΩ or higher |
| C40-84 (VCPF) - Body ground | Always | 10 kΩ or higher |
| A24-19 (VCCL)*1 - Body ground | Always | 10 kΩ or higher |
| C40-83 (VCNP)*2 - Body ground | Always | 10 kΩ or higher |
| C40-69 (VCPX)*3 - Body ground | Always | 10 kΩ or higher |
*1: for manual transaxle models
*2: w/o stop and start system for manual transaxle models
*3: w/ Gasoline Particulate Filter
Remove the VVT relay, EFI-MAIN NO. 2 relay and EFI-MAIN NO. 3 relay from the No. 1 engine room relay block and junction block assembly.
Remove the VVT relay, EFI-MAIN NO. 2 relay and EFI-MAIN NO. 3 relay connected between the checked terminals as the coil inside the relay influences the measurement value.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-9 (+B) - 1 (EFI NO. 1 fuse) | Always | Below 1 Ω |
| A24-35 (+B2) - 1 (EFI NO. 1 fuse) | Always | Below 1 Ω |
| A24-9 (+B) - Body ground | Always | 10 kΩ or higher |
| A24-35 (+B2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG