Home › Drivetrain › AXLE AND DIFFERENTIAL › DIFFERENTIAL MOUNT CUSHION › 2018.10–2020.08
RM3620E _52 Drivetrain _076176 AXLE AND DIFFERENTIAL _0373296 DIFFERENTIAL MOUNT CUSHION A

AXLE AND DIFFERENTIAL  DIFFERENTIAL MOUNT CUSHION  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear No. 1 differential mount cushion removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system for A25A-FKS:(Click here)
for M20A-FKS:(Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
Rear wheel alignment adjustment
·

Perform reset memory

·

Perform acceleration sensor zero point calibration and store system information memorization.


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (for Gasoline model) (Click here)
Television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (for Gasoline model) (Click here)
Perform headlight ECU sub-assembly LH initialization Lighting System (EXT) (Click here)
Gas leak from exhaust system is repaired Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


·

for A25A-FKS w/ Canister Pump Module:

(Click here)

·

for A25A-FKS w/o Canister Pump Module:

(Click here)

·

for M20A-FKS:

(Click here)



CAUTION:
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.


PROCEDURE

Hide 41110 1.REMOVE TORQUE VECTORING DIFFERENTIAL CARRIER ASSEMBLY (for Torque Vectoring Differential)

Hide 41110 2.REMOVE REAR DIFFERENTIAL CARRIER ASSEMBLY (except Torque Vectoring Differential)

Hide 41651 3.REMOVE REAR NO. 1 DIFFERENTIAL MOUNT CUSHION

a.

Using SST, remove the rear No. 1 differential mount cushion.

SST
09316-12010  
09570-24011  

C406797C01
5.958,0.667 5.958,0.5 5.958,0.5 6.625,0.5 false 6.5,0.833 6.5,0.5 false 6.417,0.833 6.417,0.5 false 6.438,1.75 6.271,1.75 6.271,1.75 6.104,1.667 false 4.927,2.552 5.177,2.802 0.25,0.25 10 false *a 3.5,2.844 3.75,3.094 0.25,0.25 10 false *b 6.667,0.438 7.083,0.688 0.417,0.25 10 false SST 6.469,1.688 6.719,1.938 0.25,0.25 10 false *1
*1 Rear Suspension Member Sub-assembly - -
*a Turn *b Hold
V100135

Turning Direction
V100136

Front of Vehicle
V100137

SST Bolt Position - -


NOTICE:
·

Do not bring SST into contact with the rear suspension member sub-assembly.

·

Before using SST, apply grease to SST bolt.

·

Set SST in the correct direction.

·

Do not tilt the bolt of SST.

·

Do not reuse the rear No. 1 differential mount cushion.