Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM3620E _56 Audio / Visual / Telematics _076048 NAVIGATION / MULTI INFO DISPLAY _0370120 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  C1622  Back Camera Disconnected  


DESCRIPTION

This DTC is stored if the radio and display receiver assembly judges that the signals or signal lines between the television camera assembly*1 or parking assist ECU*2 and the radio and display receiver assembly are not normal as a result of its self check.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1622 Back Camera Disconnected Open or short in the television camera assembly signal circuit
·

Harness or connector

·

Television camera assembly*1

·

Panoramic View Monitor System*2

·

Radio and display receiver assembly



*1: w/ Parking Assist Monitor System or w/ Rear View Monitor System

*2: w/ Panoramic View Monitor System


WIRING DIAGRAM

E408557E01
0.198,0.156 5.135,0.469 4.938,0.313 12 false w/ Parking Assist Monitor System or w/ Rear View Monitor System: 0.198,3.719 5.135,4.031 4.938,0.313 10 false *1: w/ Parking Assist Monitor System 0.198,4.052 5.135,4.365 4.938,0.313 10 false *2: w/ Rear View Monitor System 0.208,4.385 5.146,4.698 4.938,0.313 10 false *3: Shielded 0.625,3.063 3.146,3.323 2.521,0.26 10 false Radio and Display Receiver Assembly 0.625,2.896 3.146,3.156 2.521,0.26 10 false G2 4.854,2.927 6.417,3.188 1.563,0.26 10 false R15*1, R16*2 4.823,3.115 7.052,3.406 2.229,0.292 10 false Television Camera Assembly 1.823,2.615 2.344,2.875 0.521,0.26 10 false CSLD 1.802,2.198 2.323,2.458 0.521,0.26 10 false CGND 2.031,1.76 2.552,2.021 0.521,0.26 10 false V- 2.01,1.344 2.531,1.604 0.521,0.26 10 false V+ 1.917,0.917 2.438,1.177 0.521,0.26 10 false CA+ 5.188,0.927 5.708,1.188 0.521,0.26 10 false CB+ 5.198,1.344 5.719,1.604 0.521,0.26 10 false CV+ 5.198,1.781 5.719,2.042 0.521,0.26 10 false CV- 5.198,2.198 5.719,2.458 0.521,0.26 10 false CGND 2.313,0.813 2.833,1.073 0.521,0.26 10 false 30 2.323,1.24 2.844,1.5 0.521,0.26 10 false 28 2.333,1.667 2.854,1.927 0.521,0.26 10 false 29 2.333,2.083 2.854,2.344 0.521,0.26 10 false 27 2.333,2.5 2.854,2.76 0.521,0.26 10 false 26 3.573,2.49 6.094,2.75 2.521,0.26 10 false *3 4.99,0.823 5.51,1.083 0.521,0.26 10 false 6 4.979,1.24 5.5,1.5 0.521,0.26 10 false 3 4.979,1.667 5.5,1.927 0.521,0.26 10 false 2 4.979,2.083 5.5,2.344 0.521,0.26 10 false 5

E402603E04
5.073,1.125 5.531,1.323 0.458,0.198 10 false NS+ 5.073,1.542 5.531,1.74 0.458,0.198 10 false NS- 5.073,1.938 5.531,2.135 0.458,0.198 10 false NSG 1.854,1.094 2.313,1.292 0.458,0.198 10 false V+ 1.865,1.552 2.323,1.75 0.458,0.198 10 false V- 1.083,2.49 2.281,2.885 1.198,0.396 10 false Radio and Display Receiver Assembly 4.938,2.438 6.458,2.844 1.521,0.406 10 false Parking Assist ECU 2.177,1.021 2.635,1.219 0.458,0.198 10 false 28 2.177,1.458 2.635,1.656 0.458,0.198 10 false 29 0.302,3.302 1.552,3.583 1.25,0.281 10 false *: Shielded 3.542,1.802 4,2 0.458,0.198 10 false * 4.781,1.448 5.24,1.646 0.458,0.198 10 false 24 4.813,1 5.271,1.198 0.458,0.198 10 false 7 4.823,1.833 5.281,2.031 0.458,0.198 10 false 8 1.083,2.302 1.542,2.5 0.458,0.198 10 false G2 0.25,0.135 6.302,0.375 6.052,0.24 12 false w/ Panoramic View Monitor System: 4.927,2.26 5.385,2.458 0.458,0.198 10 false N24

CAUTION / NOTICE / HINT

NOTICE:
·

If the cable was disconnected from and reconnected to the negative (-) auxiliary battery terminal, the estimated course lines may not be displayed on the image of the area behind the vehicle. In this case, perform "Correct the Steering Angle Neutral Point".

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION

·

The following malfunctions may occur if a radio and display receiver assembly from another vehicle is installed to this vehicle. Therefore, when replacing the radio and display receiver assembly, be sure to replace it with new one.

-

Communication malfunction DTC is output

-

Does not operate normally




HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION


PROCEDURE

1.CHECK MODEL
a.

Choose the model to be inspected.

Result:
Result Proceed to
w/ Parking Assist Monitor System or w/ Rear View Monitor System A
w/ Panoramic View Monitor System B




A

2.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)

B

5.CHECK DTC (PANORAMIC VIEW MONITOR SYSTEM)
2.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the R15*1 or R16*2 television camera assembly connector.

*1: w/ Parking Assist Monitor System

*2: w/ Rear View Monitor System



b.

Disconnect the G2 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Parking Assist Monitor System:
Tester Connection Condition Specified Condition
R15-6 (CB+) - G2-30 (CA+) Always Below 1 Ω
R15-3 (CV+) - G2-28 (V+) Always Below 1 Ω
R15-2 (CV-) - G2-29 (V-) Always Below 1 Ω
R15-5 (CGND) - G2-27 (CGND) Always Below 1 Ω
R15-6 (CB+) or G2-30 (CA+) - Body ground Always 10 kΩ or higher
R15-3 (CV+) or G2-28 (V+) - Body ground Always 10 kΩ or higher
R15-2 (CV-) or G2-29 (V-) - Body ground Always 10 kΩ or higher
R15-5 (CGND) or G2-27 (CGND) - Body ground Always 10 kΩ or higher

w/ Rear View Monitor System:
Tester Connection Condition Specified Condition
R16-6 (CB+) - G2-30 (CA+) Always Below 1 Ω
R16-3 (CV+) - G2-28 (V+) Always Below 1 Ω
R16-2 (CV-) - G2-29 (V-) Always Below 1 Ω
R16-5 (CGND) - G2-27 (CGND) Always Below 1 Ω
R16-6 (CB+) or G2-30 (CA+) - Body ground Always 10 kΩ or higher
R16-3 (CV+) or G2-28 (V+) - Body ground Always 10 kΩ or higher
R16-2 (CV-) or G2-29 (V-) - Body ground Always 10 kΩ or higher
R16-5 (CGND) or G2-27 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK RADIO AND DISPLAY ASSEMBLY (CA+, CGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK RADIO AND DISPLAY ASSEMBLY (CA+, CGND)
a.
E402607C02
1.583,0.156 1.969,0.458 0.385,0.302 0.583,1.646 0.771,1.646 0.771,1.646 0.969,1.24 true 0.969,1.844 1.156,1.844 1.156,1.844 1.417,1.25 true 1.698,0.229 2.156,0.427 0.458,0.198 10 false G2 0.24,0.135 0.698,0.333 0.458,0.198 10 false *a 0.25,1.542 0.708,1.74 0.458,0.198 10 false CA+ 0.542,1.75 1.052,1.948 0.51,0.198 10 false CGND
*a Component with harness connected
(Radio and Display Receiver Assembly)


Remove the radio and display receiver assembly with the connector still connected.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G2-30 (CA+) - G2-27 (CGND) Ignition switch ACC 5.5 to 7.05 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G2-27 (CGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK TELEVISION CAMERA ASSEMBLY

NG

REPLACE RADIO AND DISPLAY ASSEMBLY

4.CHECK TELEVISION CAMERA ASSEMBLY
E402606C02
0.958,1.073 1.313,1.344 0.354,0.271 2.698,2.885 2.875,2.885 2.875,2.885 3.135,2.25 true 5,2.792 5.177,2.792 5.177,2.792 5.438,2.156 true 3.208,2.167 3.375,2.917 3.375,2.917 3.531,2.917 true 5.542,2.104 5.708,2.854 5.708,2.854 5.865,2.854 true 0.344,2.573 0.521,2.573 0.521,2.573 0.635,1.969 true 0.74,1.958 0.865,2.823 0.865,2.823 1.021,2.823 true 0.177,0.99 0.49,1.188 0.313,0.198 10 false *a 2.635,0.979 2.948,1.177 0.313,0.198 10 false *b 4.948,0.927 5.26,1.125 0.313,0.198 10 false *c 2.531,2.792 2.844,2.99 0.313,0.198 10 false *d 3.583,2.813 3.896,3.01 0.313,0.198 10 false *e 4.823,2.698 5.135,2.896 0.313,0.198 10 false *d 5.917,2.76 6.229,2.958 0.313,0.198 10 false *e 2.448,1.792 2.906,2.031 0.458,0.24 10 false GND 4.75,1.813 5.208,2.052 0.458,0.24 10 false GND 1.073,2.75 1.385,2.948 0.313,0.198 10 false V+ 0.135,2.479 0.448,2.677 0.313,0.198 10 false V- 1.063,1.125 1.375,1.323 0.313,0.198 10 false G2
*a Component with harness connected *b Waveform 1
*c Waveform 2 *d Synchronization Signal
*e Video Waveform - -


a.

Remove the radio and display receiver assembly with the connector still connected.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL


b.

Check the waveform of the television camera assembly using an oscilloscope.

Item Content
Measurement terminal G2-28 (V+) - G2-29 (V-)
Measurement setting 200 mV/DIV., 50 μsec./DIV.
Condition Waveform 1: Ignition switch ON, shift position in R, camera lens is not covered, displaying an image.
Waveform 2: Ignition switch ON, shift position in R, camera lens is covered, blacking out the screen.

HINT:
·

The video waveform changes according to the image sent by the rear camera assembly.

·

The video waveform is constantly output when the ignition switch is ACC.



OK:

Waveform is as shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

5.CHECK DTC (PANORAMIC VIEW MONITOR SYSTEM)
a.

b.

Recheck for DTCs and check that no DTCs are output.

for Gasoline Model: Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)>DTC CHECK / CLEAR

for HV Model: Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for HV Model)>DTC CHECK / CLEAR

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

6.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the N24 parking assist ECU connector.


b.

Disconnect the G2 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N24-7 (NS+) - G2-28 (V+) Always Below 1 Ω
N24-24 (NS-) - G2-29 (V-) Always Below 1 Ω
N24-7 (NS+) or G2-28 (V+) - Body ground Always 10 kΩ or higher
N24-24 (NS-) or G2-29 (V-) - Body ground Always 10 kΩ or higher
N24-8 (NSG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK PARKING ASSIST ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK PARKING ASSIST ECU
E402606C03
0.958,1.073 1.313,1.344 0.354,0.271 2.698,2.885 2.875,2.885 2.875,2.885 3.135,2.25 true 5,2.792 5.177,2.792 5.177,2.792 5.438,2.156 true 3.208,2.167 3.375,2.917 3.375,2.917 3.531,2.917 true 5.542,2.104 5.708,2.854 5.708,2.854 5.865,2.854 true 0.344,2.573 0.521,2.573 0.521,2.573 0.635,1.969 true 0.74,1.958 0.865,2.823 0.865,2.823 1.021,2.823 true 0.177,0.99 0.49,1.188 0.313,0.198 10 false *a 2.635,0.979 2.948,1.177 0.313,0.198 10 false *b 4.948,0.927 5.26,1.125 0.313,0.198 10 false *c 2.531,2.792 2.844,2.99 0.313,0.198 10 false *d 3.583,2.813 3.896,3.01 0.313,0.198 10 false *e 4.823,2.698 5.135,2.896 0.313,0.198 10 false *d 5.917,2.76 6.229,2.958 0.313,0.198 10 false *e 2.448,1.792 2.906,2.031 0.458,0.24 10 false GND 4.75,1.813 5.208,2.052 0.458,0.24 10 false GND 1.073,2.75 1.385,2.948 0.313,0.198 10 false V+ 0.135,2.479 0.448,2.677 0.313,0.198 10 false V- 1.052,1.125 1.365,1.323 0.313,0.198 10 false G2
*a Component with harness connected *b Waveform 1
*c Waveform 2 *d Synchronization Signal
*e Video Waveform - -


a.

Remove the radio and display receiver assembly with the connector still connected.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL


b.

Check the waveform of the parking assist ECU using an oscilloscope.

Item Content
Measurement terminal G2-28 (V+) - G2-29 (V-)
Measurement setting 200 mV/DIV., 50 μsec./DIV.
Condition Waveform 1: Ignition switch ON, shift position in R, camera lens is not covered, displaying an image.
Waveform 2: Ignition switch ON, shift position in R, camera lens is covered, blacking out the screen.

HINT:
·

The video waveform changes according to the image sent by the parking assist ECU.

·

The video waveform is constantly output when the ignition switch is ACC.



OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG