Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM
RM3620E _53 Suspension _076850 TIRE PRESSURE MONITORING _0374400 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  B1247  Tire Pressure Monitor Receiver Communication Stop  


DESCRIPTION

The main body ECU (multiplex network body ECU) and tire pressure warning ECU and receiver communicate by direct line. If a malfunction occurs in this communication signal, B1247 is output by the main body ECU (multiplex network body ECU).

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B1247 Tire Pressure Monitor Receiver Communication Stop Communication between the tire pressure warning ECU and receiver and main body ECU (multiplex network body ECU) is interrupted for 10 seconds or more.
·

Tire pressure warning ECU and receiver

·

Wire harness or connector

·

Main body ECU (Multiplex network body ECU)


This DTC is for main body ECU (multiplex network body ECU)

WIRING DIAGRAM

C408641E01
4.083,1.958 7.052,2.188 2.969,0.229 10 false Main Body ECU (Multiplex Network Body ECU) 4.073,1.771 4.531,1.969 0.458,0.198 10 false G45 0.385,1.771 0.844,1.969 0.458,0.198 10 false M8 0.385,1.969 3.354,2.198 2.969,0.229 10 false Tire Pressure Warning ECU and Receiver 4.656,1.031 5.115,1.229 0.458,0.198 10 false RDA 4.385,0.917 4.635,1.115 0.25,0.198 10 false 10 2.573,0.917 2.823,1.115 0.25,0.198 10 false 4 2.156,0.917 2.615,1.115 0.458,0.198 10 false RDA 1.26,1.115 1.719,1.313 0.458,0.198 10 false CPU

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs and number of the transmitters (4 or 5) stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initializationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registrationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver after the ECU has been replaced.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*


*: w/ Entry and Start System



PROCEDURE

1.INSPECT TIRE PRESSURE WARNING ECU AND RECEIVER (OUTPUT WAVEFORM)
a.
C385229C26
1.229,0.219 1.667,0.479 0.438,0.26 1.042,1.792 1.365,1.146 true 0.292,0.271 0.604,0.469 0.313,0.198 10 false *a 2.875,3.396 3.188,3.594 0.313,0.198 10 false *b 0.927,1.823 1.406,2.063 0.479,0.24 10 false RDA 1.354,0.271 1.667,0.469 0.313,0.198 10 false M8
*a Component with harness connected
(Tire Pressure Warning ECU and Receiver)
*b GND


Using an oscilloscope, check the waveform.

NOTICE:

With the connector connected, check from the backside of the connector.


Standard Voltage:
Tester Connection Tool Setting Range Condition Specified Condition
M8-4 (RDA) - Body ground 5 V/DIV.5 ms./DIV. Ignition switch ON Waveform generation



Result:
Result Proceed to
Waveform is as shown in the illustration. (Waveform alternates between 10.5 V or higher and 0.5 V or less) A
Waveform does not change from 10.5 V or higher B
Waveform does not change from 0.5 V or less C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

C

2.CHECK TERMINAL VOLTAGE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) OUTPUT)
2.CHECK TERMINAL VOLTAGE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) OUTPUT)
a.

Disconnect the tire pressure warning ECU and receiver connector.


b.
C375025C36
0.281,0.917 0.677,1.177 0.396,0.26 1.854,1.167 2.646,0.448 true 0.146,0.115 0.458,0.313 0.313,0.198 10 false *a 2.719,0.385 3.177,0.583 0.458,0.198 10 false RDA 0.344,0.969 0.802,1.167 0.458,0.198 10 false M8
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M8-4 (RDA) - Body ground Ignition switch ON 10.5 V or higher



Result:
Proceed to
OK
NG



OK

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - TIRE PRESSURE WARNING ECU AND RECEIVER)
3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Turn the ignition switch off.


b.

Disconnect the G45 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G45-10 (RDA) - M8-4 (RDA) Always Below 1 Ω
G45-10 (RDA) or M8-4 (RDA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR