Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)
RM3620E _58 Vehicle Interior _076405 SEAT _0375764 FRONT POWER SEAT CONTROL SYSTEM(for Gasoline Model with Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(for Gasoline Model with Memory)  Wireless-linked Return Function does not Operate  


DESCRIPTION

When a door is unlocked using the wireless unlock function, the certification ECU (smart key ECU assembly) sends a key ID signal to the main body ECU (multiplex network body ECU). When a door is unlocked using the entry unlock function, the certification ECU (smart key ECU assembly) sends a door unlock signal and key ID signal to the main body ECU (multiplex network body ECU). When the main body ECU (multiplex network body ECU) receives the door unlock signal, it stores the key ID. When the driver door is opened, the memory call information of the stored key ID is sent to each driving position related control ECU. Each control ECU receives the information and then performs the memory call operation according to predetermined control timing values.

CAUTION / NOTICE / HINT

NOTICE:
·

The seat position will not be stored if the SET switch and 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.

If a memorizing operation has failed, release all of the switches. The seat memory function will not operate unless the switches are released.

·

Before replacing the main body ECU (multiplex network body ECU) or certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION



PROCEDURE

1.CHECK FRONT POWER SEAT OPERATION



d.

Check the operation of memory registration of the memory call function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)>OPERATION CHECK

Result:
Result Proceed to
OK A
NG (Power seat operation) B
NG (Seat position memory function) C
NG (Seat position restoration function) D
NG (Memory registration) E




A

2.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)

B

C

GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat Position is not Memorized)

D

GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat does not Return to Memorized Position)

E

GO TO OTHER DIAGNOSIS PROCEDURE (Wireless Transmitter Memory Function does not Operate)

2.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
a.

Check the memory registration and automatic memory call function of the memory call function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)>OPERATION CHECK

Result:
Result Proceed to
Memory call function linked with the wireless unlock function does not operate. A
Memory call function linked with the entry unlock function does not operate. B
Memory call function linked with the wireless unlock function and entry unlock function both do not operate. C




A

3.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM

B

8.CHECK ENTRY AND START SYSTEM (for Entry Function)

C

13.READ VALUE USING GTS (MEMORY CALL REGISTRATION)
3.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check the wireless unlock function of the wireless door lock control system.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM (for Gasoline Model, with Entry and Start System)>OPERATION CHECK

OK:

Wireless unlock function is normal.



Result:
Proceed to
OK
NG



OK

4.REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

4.REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)
a.

Replace the position control ECU assembly (driver seat) with a new or known good one.

Click hereVehicle Interior>SEAT>POWER SEAT CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
5.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
a.

Check the memory registration and automatic memory call function of the memory call function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)>OPERATION CHECK

OK:

Memory call function linked with the wireless unlock function operates normally.



Result:
Proceed to
OK
NG



OK

END (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] WAS DEFECTIVE)

NG

6.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
6.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Replace the main body ECU (multiplex network body ECU) with a new one.

for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL

for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
7.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
a.

Check the memory registration and automatic memory call function of the memory call function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)>OPERATION CHECK

OK:

Memory call function linked with the wireless unlock function operates normally.



Result:
Proceed to
OK
NG



OK

END (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

8.CHECK ENTRY AND START SYSTEM (for Entry Function)
a.

Check the entry unlock function of the entry and start system (for entry function).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function, Gasoline Model)>OPERATION CHECK

OK:

Entry unlock function is normal.



Result:
Proceed to
OK
NG



OK

9.REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

9.REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)
a.

Replace the position control ECU assembly (driver seat) with a new or known good one.

Click hereVehicle Interior>SEAT>POWER SEAT CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

10.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
10.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
a.

Check the memory registration and automatic memory call function of the memory call function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)>OPERATION CHECK

OK:

Memory call function linked with the entry unlock function operates normally.



Result:
Proceed to
OK
NG



OK

END (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] WAS DEFECTIVE)

NG

11.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
11.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Replace the main body ECU (multiplex network body ECU) with a new one.

for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL

for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
12.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
a.

Check the memory registration and automatic memory call function of the memory call function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)>OPERATION CHECK

OK:

Memory call function linked with the entry unlock function operates normally.



Result:
Proceed to
OK
NG



OK

END (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

13.READ VALUE USING GTS (MEMORY CALL REGISTRATION)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Mem SW No. w/KeyID1 Memory switch linked with key ID1 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID1
MEM SW1: M1 switch linked with key ID1
MEM SW2: M2 switch linked with key ID1
MEM SW3: M3 switch linked with key ID1*
-
Mem SW No. w/KeyID2 Memory switch linked with key ID2 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID2
MEM SW1: M1 switch linked with key ID2
MEM SW2: M2 switch linked with key ID2
MEM SW3: M3 switch linked with key ID2*
-
Mem SW No. w/KeyID3 Memory switch linked with key ID3 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID3
MEM SW1: M1 switch linked with key ID3
MEM SW2: M2 switch linked with key ID3
MEM SW3: M3 switch linked with key ID3*
-
Mem SW No. w/KeyID4 Memory switch linked with key ID4 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID4
MEM SW1: M1 switch linked with key ID4
MEM SW2: M2 switch linked with key ID4
MEM SW3: M3 switch linked with key ID4*
-
Mem SW No. w/KeyID5 Memory switch linked with key ID5 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID5
MEM SW1: M1 switch linked with key ID5
MEM SW2: M2 switch linked with key ID5
MEM SW3: M3 switch linked with key ID5*
-
Mem SW No. w/KeyID6 Memory switch linked with key ID6 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID6
MEM SW1: M1 switch linked with key ID6
MEM SW2: M2 switch linked with key ID6
MEM SW3: M3 switch linked with key ID6*
-
Mem SW No. w/KeyID7 Memory switch linked with key ID7 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID7
MEM SW1: M1 switch linked with key ID7
MEM SW2: M2 switch linked with key ID7
MEM SW3: M3 switch linked with key ID7*
-

*: Although this item is displayed on the GTS, it is not applicable to this vehicle.


Body Electrical > Main Body > Data List
Tester Display
Mem SW No. w/KeyID1
Mem SW No. w/KeyID2
Mem SW No. w/KeyID3
Mem SW No. w/KeyID4
Mem SW No. w/KeyID5
Mem SW No. w/KeyID6
Mem SW No. w/KeyID7
50003 123 185,186,187,188,189,190,191

f.

Enter the following menus: Body Electrical / Driver Seat / Data List.


g.

Read the Data List according to the display on the GTS.

Body Electrical > Driver Seat > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Seat Memory No1 Seat position memorized with M1 switch Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-
Seat Memory No2 Seat position memorized with M2 switch Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-
Body Electrical > Driver Seat > Data List
Tester Display
Seat Memory No1
Seat Memory No2
50003 162 3,4
OK:

A seat position has been memorized for the seat position memory switch linked to the electrical key transmitter sub-assembly. (For example, the value of "Mem SW No. w/KeyID1" is MEM SW1 and the value of "Seat Memory No1" is Mem.)



Result:
Proceed to
OK
NG



OK

14.READ VALUE USING GTS (DRIVER DOOR COURTESY SWITCH)

NG

14.READ VALUE USING GTS (DRIVER DOOR COURTESY SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Courtesy SW Front door courtesy light switch assembly (driver door) signal*1 ON or OFF ON: Driver door open
OFF: Driver door closed
-
FL Door Courtesy SW Front door courtesy light switch assembly (driver door) signal*2 ON or OFF ON: Driver door open
OFF: Driver door closed
-

*1: for RHD

*2: for LHD


Body Electrical > Main Body > Data List
Tester Display
FR Door Courtesy SW
FL Door Courtesy SW
50003 123 197,199
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

15.REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

GO TO LIGHTING SYSTEM (Door Courtesy Switch Circuit)

15.REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)
a.

Replace the position control ECU assembly (driver seat) with a new or known good one.

Click hereVehicle Interior>SEAT>POWER SEAT CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

16.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
16.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
a.

Check the memory registration and automatic memory call function of the memory call function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)>OPERATION CHECK

OK:

Memory call functions linked with the wireless unlock function and entry unlock function operate normally.



Result:
Proceed to
OK
NG



OK

END (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] WAS DEFECTIVE)

NG

17.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
17.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Replace the main body ECU (multiplex network body ECU) with a new one.

for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL

for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL


Result:
Proceed to
NEXT



NEXT

18.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
18.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
a.

Check the memory registration and automatic memory call function of the memory call function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)>OPERATION CHECK

OK:

Memory call functions linked with the wireless unlock function and entry unlock function operate normally.



Result:
Proceed to
OK
NG



OK

END (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)