Use the same procedure for RHD and LHD vehicles.
The procedure below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure below is for the LH side.
69760B
1.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/o Double Locking System)
|
Install in this Direction |
Attach the clamp and install the front door inside locking cable assembly as shown in the illustration.
69720D
2.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/o Double Locking System)
|
Install in this Direction |
Attach the clamp and install the front door lock remote control cable assembly as shown in the illustration.
69036A
3.INSTALL FRONT DOOR LOCK COVER SUB-ASSEMBLY LH (w/o Double Locking System)
Attach the claw.
|
Install in this Direction |
Attach the claw and install the front door lock cover sub-assembly LH as shown in the illustration.
69318C
4.INSTALL DOOR LOCK WIRING HARNESS SEAL (w/o Double Locking System)
When reusing the removed front door lock with motor assembly LH, be sure to replace the door lock wiring harness seal on the connector with a new one.
Keep the door lock wiring harness seal of the connector free from grease and dust, etc.
Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water to enter the connecting part. This may result in a malfunction of the front door lock with motor assembly LH.
When reusing front door lock with motor assembly LH:
Install a new door lock wiring harness seal to the front door lock with motor assembly LH.
69040A
5.INSTALL FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH (w/o Double Locking System)
Using a T30 "TORX" socket wrench, install the front door lock with motor assembly LH with the 3 "TORX" screws.
69760B
6.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/ Double Locking System)
|
Install in this Direction |
Attach the clamp and install the front door inside locking cable assembly as shown in the illustration.
|
Install in this Direction |
Attach the claw and install the front door lock cover sub-assembly LH as shown in the illustration.
69720D
7.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/ Double Locking System)
|
Install in this Direction |
Attach the clamp and install the front door lock remote control cable assembly as shown in the illustration.
69318C
8.INSTALL DOOR LOCK WIRING HARNESS SEAL (w/ Double Locking System)
When reusing the removed front door lock with motor assembly LH, be sure to replace the door lock wiring harness seal on the connector with a new one.
Keep the door lock wiring harness seal of the connector free from grease and dust, etc.
Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water to enter the connecting part. This may result in a malfunction of the front door lock with motor assembly LH.
When reusing front door lock with motor assembly LH:
Install a new door lock wiring harness seal to the front door lock with motor assembly LH.
69040A
9.INSTALL FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH (w/ Double Locking System)
Using a T30 "TORX" socket wrench, install the front door lock with motor assembly LH with the 3 "TORX" screws.
69312
10.INSTALL FRONT DOOR LOCK OPEN ROD LH
|
Install in this Direction |
Install the front door lock open rod LH on the front door lock with motor assembly LH as shown in the illustration.
Check that the front door lock open rod LH is securely attached to the front door lock with motor assembly LH.
| *1 | Snap |
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Install the front door lock open rod LH to the front door outside handle frame sub-assembly LH and attach the snap of the front door outside handle as shown in the illustration.
11.INSTALL FRONT DOOR LOCK CYLINDER ASSEMBLY LH (for Driver Side)
69220
12.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH (for Driver Side)
67404F
13.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH
69802
14.INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH
68151D
15.INSTALL FRONT DOOR GLASS RUN LH
67664C
16.INSTALL DOOR FRAME GARNISH LH
68102
17.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH
67832
18.INSTALL FRONT DOOR SERVICE HOLE COVER LH
68193C
19.INSTALL FRONT DOOR FRONT BELT SEAL LH
68195B
20.INSTALL FRONT DOOR REAR BELT SEAL LH
68172A
21.INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP LH
67602
22.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH
23.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)
24.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)
74642A
25.INSTALL FRONT DOOR ASSIST GRIP COVER LH
69278B
26.INSTALL FRONT DOOR INSIDE HANDLE BEZEL LH
27.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>INSTALLATION
for A25A-FKS:
for M20A-FKS:
Click hereGeneral>MAINTENANCE>M20A-FKS BATTERY>INSTALLATION
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
65351A
28.INSTALL BATTERY HOLE COVER (for HV Model)
58416K
29.INSTALL REAR NO. 2 FLOOR BOARD (for HV Model)
58410B
30.INSTALL DECK BOARD ASSEMBLY (for HV Model)
31. INITIALIZE POWER WINDOW CONTROL SYSTEM
32. CHECK POWER WINDOW CONTROL SYSTEM
33. CHECK POWER DOOR LOCK CONTROL SYSTEM