Use the same procedure for RHD and LHD vehicles.
The procedure below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure below is for the LH side.
75922M
1.INSTALL NO. 1 BLACK OUT TAPE LH (w/ Black Out Tape)
75986G
2.INSTALL FRONT DOOR OUTSIDE STRIPE LH (w/ Black Out Tape)
75966B
3.INSTALL FRONT DOOR NO. 4 STRIPE LH (w/ Black Out Tape)
67001A
4.INSTALL FRONT DOOR PANEL CUSHION
Attach the claw and install the front door panel cushion.
Use the same procedure described for the other side.
5.INSTALL HOLE PLUG
Install the hole plug.
Use the same procedure described for the other side.
6.INSTALL SCREW GROMMET
Attach the claw and install the screw grommet.
Use the same procedure described for the other side.
75074
7.INSTALL FRONT DOOR LOWER OUTSIDE MOULDING SUB-ASSEMBLY LH
67864B
8.INSTALL FRONT DOOR NO. 2 WEATHERSTRIP LH
Attach the clip and install the front door No. 2 weatherstrip LH.
75754A
9.INSTALL FRONT DOOR UPPER WINDOW FRAME MOULDING LH
75792
10.INSTALL DOOR WINDOW FRAME MOULDING CLIP
Attach the claw to install a new door window frame moulding clip.
67856B
11.INSTALL FRONT DOOR PANEL PROTECTOR LH
75756D
12.INSTALL DOOR WINDOW FRAME MOULDING LH (CENTER PILLAR SIDE)
67862
13.INSTALL FRONT DOOR WEATHERSTRIP LH
Attach the clip and install the front door weatherstrip LH.
| *a | Correct |
| *b | Incorrect |
Check that the front door weatherstrip LH is securely installed to the rail of the front door outside moulding sub-assembly LH as shown in the illustration.
If the front door weatherstrip LH is not securely installed, water may leak into the vehicle.
68620
14.INSTALL FRONT DOOR CHECK ASSEMBLY LH
When reusing a bolt (B):
Clean the threads of the bolt with non-residue solvent.
Apply adhesive to the threads of the bolt.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.
|
Bolt (A) |
|
Bolt (B) |
Install the front door check assembly LH with the 2 bolts (A) and bolt (B).
69760B
15.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/o Double Locking System)
69720D
16.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/o Double Locking System)
69036A
17.INSTALL FRONT DOOR LOCK COVER SUB-ASSEMBLY LH (w/o Double Locking System)
69318C
18.INSTALL DOOR LOCK WIRING HARNESS SEAL (w/o Double Locking System)
When reusing front door lock with motor assembly LH:
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSTALLATION
69040A
19.INSTALL FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH (w/o Double Locking System)
69760B
20.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/ Double Locking System)
69720D
21.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/ Double Locking System)
69318C
22.INSTALL DOOR LOCK WIRING HARNESS SEAL (w/ Double Locking System)
69040A
23.INSTALL FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH (w/ Double Locking System)
69202A
24.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH
Apply MP grease to the sliding parts of the front door outside handle frame sub-assembly LH.
w/ Entry and Start System:
Attach the wire harness clamp.
| *a | Inside |
| *b | Outside |
Attach the guide as shown in the illustration.
Using a T30 "TORX" socket wrench, install the front door outside handle frame sub-assembly LH with the "TORX" screw.
69312
25.INSTALL FRONT DOOR LOCK OPEN ROD LH
|
Install in this Direction |
Install the front door lock open rod LH on the front door lock with motor assembly LH as shown in the illustration.
Check that the front door lock open rod LH is securely attached to the front door lock with motor assembly LH.
| *1 | Snap |
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Install the front door lock open rod LH to the front door outside handle frame sub-assembly LH and attach the snap of the front door outside handle as shown in the illustration.
69242F
26.INSTALL FRONT DOOR REAR OUTSIDE HANDLE PAD
Attach the guide and install the front door rear outside handle pad.
69241H
27.INSTALL FRONT DOOR FRONT OUTSIDE HANDLE PAD
Attach the claw and guide to install the front door front outside handle pad.
28.INSTALL FRONT DOOR LOCK CYLINDER ASSEMBLY LH (for Driver Side)
Apply MP grease to the sliding parts of the front door lock cylinder assembly LH.
Using a T30 "TORX" socket wrench, install the front door lock cylinder assembly LH with the "TORX" screw.
Install the hole plug.
69217E
29.INSTALL FRONT DOOR OUTSIDE HANDLE COVER RH (for Front Passenger Side)
|
Install in this Direction |
Attach the claw of the front door outside handle cover RH in the direction indicated by the arrow.
Using a T30 "TORX" socket wrench, install the front door outside handle cover RH with the "TORX" screw.
Install the hole plug.
69220
30.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH
|
Install in this Direction |
Install the front door outside handle assembly LH in the direction of the arrow shown in the illustration.
| *1 | Holder |
|
Install in this Direction |
Attach the holder as shown in the illustration.
w/ Entry and Start System:
Attach the claw to connect the connector and connector cover.
|
Install in this Direction |
Attach the claw and close the connector cover as shown in the illustration.
68126
31.INSTALL FRONT DOOR FIX WINDOW GLASS LH
|
Install in this Direction |
Install the front door fix window glass LH as shown in the illustration.
67402F
32.INSTALL FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY LH
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Temporarily install the front door front lower frame sub-assembly LH in the direction indicated by the arrows, in the order shown in the illustration.
Install the 3 bolts.
|
Lift up in this Direction |
Lift up the front door weatherstrip LH and install the screw as shown in the illustration.
Install the screw.
67404F
33.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH
Attach the guide.
Install the front door rear lower frame sub-assembly LH with the bolt.
85720C
34.INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
69802
35.INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH
Apply MP grease to the sliding parts of the front door window regulator sub-assembly LH.
|
Install in this Direction |
Insert the front door window regulator sub-assembly LH to the service hole as shown in the illustration.
|
Nut |
|
Connector |
Install the front door window regulator sub-assembly LH with the 7 nuts in the order shown in the illustration.
Do not damage the front door panel with the front door window regulator sub-assembly LH.
Connect the connector.
68151D
36.INSTALL FRONT DOOR GLASS RUN LH
Install the front door glass run LH to the groove in front door front lower frame sub-assembly LH and front door rear lower frame sub-assembly LH.
67664C
37.INSTALL DOOR FRAME GARNISH LH
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Attach the guide and install the door frame garnish LH in the direction indicated by the arrows, in the order shown in the illustration.
68102
38.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH
for Driver Side:
Connect the multiplex network master switch assembly connector.
for Front Passenger Side:
Connect the power window regulator switch assembly connector.
Connect the cable to the negative (-) auxiliary battery terminal.
for A25A-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>INSTALLATION
for A25A-FKS:
for M20A-FKS:
Turn the ignition switch to ON.
Move the front door window regulator sub-assembly LH until the installation bolts can be seen.
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Temporarily install the front door glass sub-assembly LH to the front door window regulator assembly LH in the order shown in the illustration.
Be careful not to damage the front door glass sub-assembly LH.
Install the front door glass sub-assembly LH with the 2 bolts.
Move the front door glass sub-assembly LH until the open position.
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
for A25A-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>REMOVAL
for A25A-FKS:
for M20A-FKS:
Click hereGeneral>MAINTENANCE>M20A-FKS BATTERY>REMOVAL
After disconnecting the cable from the negative (-) auxiliary battery terminal, wait for at least 90 seconds to start the operation.
If the airbag deploys for any reason, it may cause a serious accident.
for Driver Side:
Disconnect the multiplex network master switch assembly connector.
for Front Passenger Side:
Disconnect the power window regulator switch assembly connector.
Remove the protective tape.
Install the hole plug.
75712B
39.INSTALL FRONT DOOR BELT MOULDING LH
8983AA
40.INSTALL SIDE AIRBAG PRESSURE SENSOR LH
67832
41.INSTALL FRONT DOOR SERVICE HOLE COVER LH
|
Install in this Direction |
Pass the front door lock remote control cable assembly and front door inside locking cable assembly through the front door service hole cover LH.
| *a | Clip A |
Align with the position of clip A as shown in the illustration.
Attach the clip and install the front door service hole cover LH in the order shown in the illustration.
| *a | Bead Mark |
|
Turn in this Direction |
|
Service Hole Cover Clip |
Install the service hole cover clip knob at an angle of 45°.
Turn the service hole cover clip 45° clockwise and align the positions of the bead mark and knob.
Use the same procedure for the other service hole cover clips.
Attach the clamp.
Connect the connector.
86160
42.INSTALL FRONT NO. 1 SPEAKER ASSEMBLY
87940
43.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH
87964
44.INSTALL OUTER MIRROR INSTALL HOLE COVER LH
68193C
45.INSTALL FRONT DOOR FRONT BELT SEAL LH
|
Install in this Direction |
Install the front door front belt seal LH as shown in the illustration.
|
Install in this Direction |
Attach the guide and partially install the front door weatherstrip LH with the clip.
68195B
46.INSTALL FRONT DOOR REAR BELT SEAL LH
|
Install in this Direction |
Install the front door rear belt seal LH to the front door inner glass weatherstrip LH as shown in the illustration.
68172A
47.INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP LH
|
Install in this Direction |
Install the front door inner glass weatherstrip LH with front door rear belt seal LH as shown in the illustration.
|
Install in this Direction |
Attach the guide and partially install the front door weatherstrip LH with the clip.
69206B
48.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH
|
Install in this Direction |
Temporarily install the front door inside handle sub-assembly LH in the direction indicated by the arrow as shown in the illustration.
Attach the claw and clamp to install the front door inside handle sub-assembly LH.
84927
49.INSTALL SEAT MEMORY SWITCH (w/ Seat Memory Switch)
67602
50.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH
w/ Seat Memory Switch:
Connect the connector.
| *1 | Front Door Inside Looking Cable Assembly |
| *2 | Front Door Lock Remote Control Cable Assembly |
|
Install in this Direction |
Attach the clamp and connect the front door lock remote control cable assembly and front door inside locking cable assembly to the front door inside handle sub-assembly as shown in the illustration.
|
Install in this Direction |
Attach the claw and clip to install the front door trim board sub-assembly LH in the direction indicated by the arrow shown in the illustration.
Attach the claws and clips as shown in the illustration.
|
Install in this Direction |
Attach the clip and install the 3 screws as shown in the illustration.
Remove the protective tape.
84930
51.INSTALL DOOR CONTROL SWITCH ASSEMBLY (w/ Door Control Switch)
84810
52.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)
84870A
53.INSTALL OUTER MIRROR SWITCH ASSEMBLY (for Driver Side)
84040
54.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (for Driver Side)
55.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)
Connect the 2 connectors.
|
Install in this Direction |
Attach the guide in the direction indicated by the arrow shown in the illustration.
|
Install in this Direction |
Attach the guide and claw to install the multiplex network master switch assembly with front door armrest base panel.
Remove the protective tape.
56.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)
w/ Door Control Switch:
Connect the 2 connectors.
w/o Door Control Switch:
Connect the connector.
|
Install in this Direction |
Attach the guide in the direction indicated by the arrow shown in the illustration.
|
Install in this Direction |
Attach the guide and claw to install the power window regulator switch assembly with front door armrest base panel.
Remove the protective tape.
74642A
57.INSTALL FRONT DOOR ASSIST GRIP COVER LH
|
Install in this Direction |
Attach the guide in the direction indicated by the arrow shown in the illustration.
|
Install in this Direction |
Attach the claw in the order shown in the illustration.
Attach the clip and install the front door assist grip cover LH.
Remove the protective tape.
69278B
58.INSTALL FRONT DOOR INSIDE HANDLE BEZEL LH
Attach the claw and install the door inside handle bezel LH.
59.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>INSTALLATION
for A25A-FKS:
for M20A-FKS:
Click hereGeneral>MAINTENANCE>M20A-FKS BATTERY>INSTALLATION
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
65351A
60.INSTALL BATTERY HOLE COVER (for HV Model)
58416K
61.INSTALL REAR NO. 2 FLOOR BOARD (for HV Model)
58410B
62.INSTALL DECK BOARD ASSEMBLY (for HV Model)
63.INSPECT SRS WARNING LIGHT
for HV Model with Occupant Classification System:
for Gasoline Model with Occupant Classification System:
w/o Occupant Classification System:
64. PERFORM DIAGNOSTIC SYSTEM CHECK
for HV Model with Occupant Classification System:
for Gasoline Model with Occupant Classification System:
w/o Occupant Classification System:
65. INITIALIZE POWER WINDOW CONTROL SYSTEM
66. CHECK POWER WINDOW CONTROL SYSTEM
67. CHECK POWER DOOR LOCK CONTROL SYSTEM
68.INSPECT OUTER REAR VIEW MIRROR OPERATION
w/ Retract Mirror:
Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Retract Mirror)>OPERATION CHECK
w/o Retract Mirror:
Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/o Retract Mirror)>OPERATION CHECK
69.PERFORM SYSTEM INITIALIZATION AND CALIBRATION (w/ Panoramic View Monitor System)
for Gasoline Model:
70.INSPECT CHECK FRONT POWER SEAT CONTROL SYSTEM (for Power Seat)
for HV Model:
for Gasoline Model: