Home › Vehicle Interior › SEAT BELT › OCCUPANT DETECTION SENSOR › 2018.10–2020.08
RM3620E _58 Vehicle Interior _076406 SEAT BELT _0377518 OCCUPANT DETECTION SENSOR A

SEAT BELT  OCCUPANT DETECTION SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during separate type front seat cushion pad (occupant detection sensor) removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) battery terminal Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
Front passenger seat Zero point calibration (Occupant classification system)
·

Occupant classification system (for HV model)

·

Passenger airbag ON/OFF indicator

·

Airbag system (Front passenger side)

·

Seat belt warning system (Front passenger)


(Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system for A25A-FKS:(Click here)
for M20A-FKS:(Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
Front passenger seat Zero point calibration (Occupant Classification System)
·

Occupant classification system (for Gasoline model)

·

Passenger airbag ON/OFF indicator

·

Airbag system (Front passenger side)

·

Seat belt warning system (Front passenger)


(Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


CAUTION:
·
B521791

Wear protective gloves. Sharp areas on the parts may injure your hands.

·

There is risk of injury.



HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
·
B458500

Be sure to read precaution thoroughly before servicing.


·
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If an SRS part is accidentally deployed, it may cause a serious injury.



NOTICE:
·

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



Hide 2.REMOVE FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>REMOVAL


Hide 72551B 3.REMOVE RECLINING HINGE COVER RH

HINT:

Use the same procedure described for the LH side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY


Hide 72525A 4.REMOVE RECLINING ADJUSTER RELEASE HANDLE RH

HINT:

Use the same procedure described for the LH side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY


Hide 71811D 5.REMOVE FRONT SEAT CUSHION SHIELD RH

Hide 71861 6.REMOVE FRONT SEAT INNER CUSHION SHIELD RH

Hide 7.REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY

Hide 8.REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD

a.

w/o Climate Control Seat System, w/ Seat Heater System:

i.
B532233

Detach the claw and clamp.



b.

w/ Climate Control Seat System, w/ Seat Heater System:

i.
B521399

Disconnect the connector.


ii.

Detach the clamp.



c.
B521489

Disconnect the connector.


d.
B521490C02
0,0 0,0 false
V100155

Protective Tape


Using a thin-bladed screwdriver, detach the claw to remove the connector of the occupant detection sensor from the connector holder.

HINT:

Tape the thin-bladed screwdriver tip before use.



e.
B532228

Detach the hook.


f.

Detach the hook to remove the separate type front seat cushion cover with pad.

B532229


Hide 71511S 9.REMOVE SEPARATE TYPE FRONT SEAT CUSHION PAD (OCCUPANT DETECTION SENSOR)

a.
B532230C01
1.021,1.99 1.677,1.594 true 0.854,1.948 1.167,2.104 0.313,0.156 10 false *a
*a Band
V113147

Remove in this Direction


Detach the band.


b.

for Standard Seat Type:

i.

Using a thin-bladed screwdriver, detach the hook to remove the separate type front seat cushion pad (occupant detection sensor) from the separate type front seat cushion cover as shown in the illustration.

B529815C01
0,0 0,0 false
V100155

Protective Tape - -


NOTICE:

Do not dirty or damage the separate type front seat cushion cover.


HINT:

Tape the thin-bladed screwdriver tip before use.




c.

for Sports Seat Type:

i.

Using a thin-bladed screwdriver, detach the hook to remove the separate type front seat cushion pad (occupant detection sensor) from the separate type front seat cushion cover as shown in the illustration.

B521400C01
0,0 0,0 false
V100155

Protective Tape - -


NOTICE:

Do not dirty or damage the separate type front seat cushion cover.


HINT:

Tape the thin-bladed screwdriver tip before use.