Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT DOOR WINDOW FRAME MOULDING › 2018.10–2019.02
RM3620E _59 Vehicle Exterior _076404 EXTERIOR PANELS / TRIM _0377755 FRONT DOOR WINDOW FRAME MOULDING A

EXTERIOR PANELS / TRIM  FRONT DOOR WINDOW FRAME MOULDING  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

Use the same procedure described for the LH side.



PROCEDURE

Hide 75754A 1.INSTALL FRONT DOOR UPPER WINDOW FRAME MOULDING LH

a.

Attach the guide to temporarily install the front door upper window frame moulding LH to the front door frame.

B524084


b.

Using an air riveter or hand riveter with a nose piece, install the front door upper window frame moulding LH with 7 new φ4.0 mm (0.157 in.) waterproof rivets.

NOTICE:
·
B171664C27
1.229,1.042 1.083,1.573 1.083,1.573 1.271,2.281 false 1.083,1.573 0.813,1.573 false 1.75,0.833 2.031,1.583 2.031,1.583 1.74,2.521 false 2.031,1.573 2.313,1.573 false 2.271,0.542 2.469,0.74 0.198,0.198 10 false *a 2.271,2.385 2.49,2.583 0.219,0.198 10 false *b 0.594,1.479 0.781,1.677 0.188,0.198 10 false *1 2.354,1.5 2.542,1.677 0.188,0.177 10 false *2
*1 Riveter
*2 Mandrel
*a INCORRECT
*b CORRECT


Do not pry the rivet with the riveter as this will cause damage to the riveter and mandrel.

·
B172390C28
2.325,0.536 2.513,0.713 0.189,0.177 10 *a 2.325,1.527 2.5,1.705 0.175,0.177 10 *a 2.434,2.73 2.634,2.907 0.2,0.177 10 *b 0.72,0.066 1.023,0.066 false 0.818,1.11 1.018,1.11 false 1.043,2.324 1.223,2.477 0.181,0.153 10 *1 1.043,1.044 1.223,1.196 0.181,0.153 10 *1 1.043,0.0040 1.223,0.157 0.181,0.153 10 *1 0.818,2.402 1.018,2.402 false
*1 Riveter
*a INCORRECT
*b CORRECT


Confirm that the rivets are seated properly against the front door upper window frame moulding LH.

·

Do not tilt the riveter when installing the rivet to the front door upper window frame moulding LH.

·

Do not leave any space between the rivet head and front door upper window frame moulding LH.

·
B172391C27
2.304,0.996 2.504,1.173 0.2,0.177 10 *a 2.408,2.434 2.62,2.612 0.211,0.177 10 *b 0.978,0.515 1.173,0.686 0.195,0.171 10 *1 0.735,0.603 0.941,0.603 false 0.973,2.023 1.182,2.194 0.209,0.171 10 *1 0.731,2.111 0.937,2.111 false
*1 Riveter
*a INCORRECT
*b CORRECT


Do not leave any space between the front door upper window frame moulding LH and front door panel. Firmly hold together the 2 items while installing the rivet.



HINT:

If the mandrel of the rivet does not come off on the first operation of the rivet gun, slide the rivet gun forward on the mandrel and operate it again.



Hide 67856B 2.INSTALL FRONT DOOR PANEL PROTECTOR LH

a.
B524086C02
0,0 0,0 false
V113147

Install in this Direction


Install the front door panel protector LH.


Hide 75756D 3.INSTALL FRONT DOOR WINDOW FRAME MOULDING LH (CENTER PILLAR SIDE)

HINT:

When installing a new front door window frame moulding LH (center pillar side), heat the front door panel and front door window frame moulding LH (center pillar side) using a heat light.


Heating Temperature
Item Temperature
Front Door Panel 40 to 60°C (104 to 140°F)
Front Door Window Frame Moulding LH (Center Pillar Side) 20 to 30°C (68 to 86°F)

CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the front door panel and front door window frame moulding LH (center pillar side) excessively.


a.

Clean the front door panel surface.

i.

Using a heat light, heat the front door panel surface.


ii.

Remove any double-sided tape from the front door panel.


iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the front door window frame moulding LH (center pillar side) with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.


·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.





b.
B524087C01
1.656,1.208 1.927,1.448 true 1.979,1.469 2.135,1.625 0.156,0.156 10 true *a
*a Double-sided Tape
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Install a new front door window frame moulding LH (center pillar side).

i.

Using a heat light, heat the front door panel and front door window frame moulding LH (center pillar side).


ii.

Remove the release paper from the front door window frame moulding LH (center pillar side).

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



iii.

Attach the guide and clip and double-sided tape to install the front door window frame moulding LH (center pillar side).

HINT:

Press the front door window frame moulding LH (center pillar side) firmly to install it.




c.

Remove the protective tape.


Hide 67862 4.INSTALL FRONT DOOR WEATHERSTRIP LH

a.
B524172

Attach the clip and install the front door weatherstrip LH.


b.
B524244C01
1.063,1.26 1.375,1.458 0.313,0.198 10 false *a 1.073,2.281 1.385,2.479 0.313,0.198 10 false *b
*a Correct
*b Incorrect


Check that the front door weatherstrip LH is securely installed to the rail of the front door outside moulding sub-assembly LH as shown in the illustration.

NOTICE:

If the front door weatherstrip LH is not securely installed, water may leak into the vehicle.



Hide 68126 5.INSTALL FRONT DOOR FIX WINDOW GLASS LH

Hide 67402F 6.INSTALL FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY LH

Hide 68151D 7.INSTALL FRONT DOOR GLASS RUN LH

Hide 67664C 8.INSTALL DOOR FRAME GARNISH LH

Hide 68102 9.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH

Hide 75712B 10.INSTALL FRONT DOOR BELT MOULDING LH

Hide 67832 11.INSTALL FRONT DOOR SERVICE HOLE COVER LH

Hide 68193C 12.INSTALL FRONT DOOR FRONT BELT SEAL LH

Hide 68172A 13.INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP LH

Hide 67602 14.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

Hide 15.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

Hide 16.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

Hide 74642A 17.INSTALL FRONT DOOR ASSIST GRIP COVER LH

Hide 69278B 18.INSTALL FRONT DOOR INSIDE HANDLE BEZEL LH

Hide 19.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL



c.

for M20A-FKS:

Click hereGeneral>MAINTENANCE>M20A-FKS BATTERY>INSTALLATION

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



Hide 65351A 20.INSTALL BATTERY HOLE COVER (for HV Model)

Hide 58416K 21.INSTALL REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 58410B 22.INSTALL DECK BOARD ASSEMBLY (for HV Model)

Hide 23. INITIALIZE POWER WINDOW CONTROL SYSTEM

Hide 24. CHECK POWER WINDOW CONTROL SYSTEM

Hide 25. CHECK POWER DOOR LOCK CONTROL SYSTEM