Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE PEDAL STROKE SENSOR (for LHD without Vacuum Brake Booster)
RM3620E _54 Brake _076410 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0378111 BRAKE PEDAL STROKE SENSOR(for LHD without Vacuum Brake Booster) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE PEDAL STROKE SENSOR(for LHD without Vacuum Brake Booster)  INSTALLATION  


PROCEDURE

Hide 89510D 2.INSTALL BRAKE PEDAL STROKE SENSOR ASSEMBLY

NOTICE:
·

Do not drop the brake pedal stroke sensor assembly.

·

If the brake pedal stroke sensor assembly has been dropped, replace the brake pedal stroke sensor assembly with a new one.



a.

When installing a new brake pedal stroke sensor assembly:

NOTICE:

Do not break the brake pedal stroke sensor assembly lever set pin before installing the brake pedal stroke sensor assembly with the 2 nuts.


i.
C437703C02
2.438,0.656 2.438,0.323 2.438,0.323 2.771,0.323 true 2.677,0.844 2.677,1.01 2.677,1.01 3.01,1.01 true 0.656,0.76 0.99,0.76 true 0.896,4.198 0.896,3.865 false 2.802,0.219 2.99,0.417 0.188,0.198 10 true *a 3.042,0.927 3.229,1.125 0.188,0.198 10 true *b 0.427,0.667 0.615,0.865 0.188,0.198 10 true *c 2.198,4.271 2.385,4.469 0.188,0.198 10 true *d 0.76,4.219 1.125,4.458 0.365,0.24 10 true SST 0.604,1.583 0.74,1.76 0.135,0.177 10 true B 1.542,3.063 1.677,3.24 0.135,0.177 10 true A
*a Brake Pedal Stroke Sensor Assembly Lever
*b Brake Pedal Groove
*c Brake Pedal Stroke Sensor Assembly Lever Set Pin
*d Torque Wrench Fulcrum Length


Install a new brake pedal stroke sensor assembly to the brake pedal support assembly with the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:
·

Engage the brake pedal stroke sensor assembly lever with the brake pedal groove.

·

Check that there is no foreign matter attached to the contact surface of the brake pedal stroke sensor assembly.

·

Check that the tip of the brake pedal stroke sensor assembly lever is protruding from the brake pedal groove.




ii.

Using SST, fully tighten the 2 nuts.

SST
09961-00950  

Torque:
Specified tightening torque : 8.5 N*m (87 kgf*cm, 75 in.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 150 mm (5.91 in.)) + torque wrench (fulcrum length of 185 mm (7.28 in.)):

4.7 N*m (48 kgf*cm, 42 in.*lbf)




iii.

Connect the connector.


iv.

Firmly depress the brake pedal to break the brake pedal stroke sensor assembly lever set pin.


v.

Remove the broken lever set pin.



b.

When reusing the brake pedal stroke sensor assembly:

i.
C408243C01
2.073,1.052 1.906,1.052 1.906,1.052 1.906,0.854 true 1.979,0.271 1.729,0.271 1.729,0.271 1.729,0.688 true 2,0.198 2.167,0.365 0.167,0.167 10 true *a 2.104,0.979 2.281,1.135 0.177,0.156 10 true *b
*a Brake Pedal Stroke Sensor Assembly Lever
*b Brake Pedal Groove


Install the brake pedal stroke sensor assembly to the brake pedal support assembly and temporarily tighten the 2 nuts.

NOTICE:
·

Engage the brake pedal stroke sensor assembly lever with the brake pedal groove.

·

Check that there is no foreign matter attached to the contact surface of the brake pedal stroke sensor assembly.

·

Check that the tip of the brake pedal stroke sensor assembly lever is protruding from the brake pedal groove.




ii.

Connect the connector.



Hide 3.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>INSTALLATION

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 89510D 4.ADJUST BRAKE PEDAL STROKE SENSOR ASSEMBLY

NOTICE:

When the brake pedal stroke sensor assembly is being reused, perform the following procedure to adjust it.


a.

Connect the GTS to the DLC3 with the power switch off.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Stroke Sensor.

Chassis > ABS/VSC/TRC > Data List
Tester Display
Stroke Sensor
50003 105 11

e.
C437704C03
0.917,3 0.917,2.667 false 0.792,3.01 1.24,3.26 0.448,0.25 10 false SST 2.198,3.052 2.646,3.302 0.448,0.25 10 false *a
*a Torque Wrench Fulcrum Length


Read the stroke sensor value in the Data List, and turn the brake pedal stroke sensor assembly slowly to the right or left to adjust the output voltage so that it is within the following range.

Standard Voltage (without the brake pedal depressed):

0.8 to 1.2 V



f.

Using SST, fully tighten the 2 nuts.

SST
09961-00950  

Torque:
Specified tightening torque : 8.5 N*m (87 kgf*cm, 75 in.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 150 mm (5.91 in.)) + torque wrench (fulcrum length of 185 mm (7.28 in.)):

4.7 N*m (48 kgf*cm, 42 in.*lbf)




g.

Turn the GTS off and turn the power switch off.


h.

Disconnect the GTS from the DLC3.


Hide 55606 5.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 62112 6.INSTALL COWL SIDE TRIM BOARD LH

Hide 67914B 7.INSTALL FRONT DOOR SCUFF PLATE LH

Hide 8.PERFORM INITIALIZATION AND CALIBRATION OF LINEAR SOLENOID VALVE AND ZERO POINT OF YAW RATE AND ACCELERATION SENSOR