Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER PUMP(for RHD without Vacuum Brake Booster)
RM3620E _54 Brake _076411 BRAKE SYSTEM (OTHER) _0377042 BRAKE BOOSTER PUMP(for RHD without Vacuum Brake Booster) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER PUMP(for RHD without Vacuum Brake Booster)  INSTALLATION  


PROCEDURE

Hide 47070 1.INSTALL BRAKE BOOSTER PUMP ASSEMBLY

a.
C378032C01
2.188,0.833 2.344,0.833 true 2.792,0.771 2.99,0.771 true 2.031,0.771 2.344,0.927 0.313,0.156 10 false *1 3.031,0.708 3.344,0.865 0.313,0.156 10 false *2
*1 Brake Booster Pump Collar
*2 Brake Booster Pump Bushing


Install the 2 brake booster pump collars and 2 brake booster pump bushings to the brake booster pump assembly as shown in the illustration.

HINT:

Perform this procedure only when replacement of the brake booster pump collars or brake booster pump bushings is necessary.



b.

Connect the brake booster pump assembly, brake booster pump bushing and No. 2 brake actuator case collar to the brake actuator bracket assembly as shown in the illustration.

C409077C01
4.635,1.656 4.781,1.656 false 4.094,1.906 4.427,1.906 true 4.823,1.594 5.135,1.75 0.313,0.156 10 false *1 3.927,1.823 4.24,1.979 0.313,0.156 10 false *2
*1 Brake Booster Pump Collar *2 Brake Booster Pump Bushing


NOTICE:
·

Be careful not to allow brake fluid to enter the connector.

·

When installing the brake booster pump assembly to the brake actuator bracket assembly, confirm that the 2 brake booster pump bushings and 2 brake booster pump collars are installed to the brake booster pump assembly.

·

Do not drop the brake booster pump assembly when carrying it.

·

Do not install a brake booster pump assembly that has been dropped.

·

Do not remove the hole plugs of a new brake booster pump assembly before connecting the brake lines because the brake booster pump assembly is filled with brake fluid.

·
C410926C01
0.729,1.823 0.896,1.823 0.896,1.823 1.135,1.615 false 2.354,0.854 2.833,0.625 2.833,0.625 3,0.625 false 2.323,1.354 2.688,1.042 2.688,1.042 2.854,1.042 false 2.198,1.74 2.573,1.469 2.573,1.469 2.771,1.469 true 0.5,1.698 0.813,1.854 0.313,0.156 10 false *a 3.104,0.531 3.375,0.802 0.271,0.271 10 false *b 2.969,0.938 3.281,1.094 0.313,0.156 10 false *c 2.865,1.385 3.188,1.708 0.323,0.323 10 false *d
*a Union
*b Connector
*c Wire Harness
*d Stud


Do not carry the brake booster pump assembly by the parts shown in the illustration.




c.
C407903

Install the nut.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


d.
C407902

Engage the 2 clamps to connect the wire harness to the brake actuator bracket assembly.


e.
C407901

Engage the clamp to install a new brake tube clamp to the brake actuator bracket assembly.


Hide 44572C 2.INSTALL NO. 2 BRAKE ACTUATOR HOSE

a.
C409070C01
1.177,2.344 1.323,2.344 1.323,2.344 1.844,2.771 true 1.99,2.281 2.448,2.479 0.458,0.198 10 false 90° 2,3.167 2.458,3.365 0.458,0.198 10 false 90° 0.99,2.24 1.448,2.438 0.458,0.198 10 false *a
*a Identification Mark
V100135

Rear of the vehicle
V100136

Up


Install the No. 2 brake actuator hose to the brake booster pump assembly and slide the clip to secure it.

NOTICE:
·

Make sure to connect the No. 2 brake actuator hose with its identification mark facing the rear of the vehicle.

·

Install the clip within the range shown in the illustration.




Hide 3.INSTALL BRAKE BOOSTER PUMP ASSEMBLY WITH BRACKET

a.
C407899C02
2.583,3.083 2.938,3.083 true 2.146,4.583 2.333,4.583 2.333,4.583 2.333,4.167 true 0.823,4 1.177,4 true 2.563,3.885 2.917,3.885 true 0.635,3.896 0.948,4.052 0.313,0.156 10 false *a 3,2.99 3.313,3.146 0.313,0.156 10 false *b 2.969,3.802 3.25,3.979 0.281,0.177 10 false *c 1.969,4.49 2.219,4.667 0.25,0.177 10 false *d 1.427,1.76 1.677,1.969 0.25,0.208 10 true 1 3.115,0.854 3.365,1.063 0.25,0.208 10 true 2 1.896,1.906 2.146,2.115 0.25,0.208 10 true 3
*a Union
*b Connector
*c Wire Harness
*d Stud


Temporarily install the brake booster pump assembly with bracket to the vehicle body with the 2 bolts and nut.

NOTICE:
·

Do not apply excessive force to the brake lines.

·

Do not carry the brake booster pump assembly by the parts shown in the illustration.

·

Do not drop the brake booster pump assembly when carrying it.

·

Be careful not to allow brake fluid to enter the connector.

·

Do not remove the hole plugs of a new brake booster pump assembly before connecting the brake lines because the brake booster pump assembly is filled with brake fluid.



HINT:

Install the 2 bolts from the bottom of the vehicle.



b.

Tighten the 2 bolts and nut in the order shown in the illustration.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


c.
C409075C01
0,0 0,0 false
V113147

Connect the connector
V113148

Lock the lock lever


Connect the connector to the brake booster pump assembly and lock the lock lever as shown in the illustration.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the connector can be connected smoothly.

·

Do not allow water, oil or dirt to enter the connector.




Hide 47315 4.CONNECT NO. 5 FRONT BRAKE TUBE

a.
C407897

Install a new brake tube clamp to the vehicle body with the bolt.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


b.
C407898

Engage the clamp to connect the brake tube clamp to the No. 5 front brake tube.


c.
C407896

Engage the 3 clamps to connect the brake tube clamp to the brake lines.


d.
C409072C01
2.833,2.948 2.667,2.948 2.667,2.948 2.667,2.698 false 1.677,2.969 1.99,3.125 0.313,0.156 10 false *a 2.885,2.865 3.188,3.094 0.302,0.229 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, connect the No. 5 front brake tube to the brake tube way.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the accumulator to brake master cylinder tube.

·

Do not allow the accumulator to brake master cylinder tube to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the accumulator to brake master cylinder tube from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




Hide 473A1 5.CONNECT ACCUMULATOR TO BRAKE MASTER CYLINDER TUBE

a.
C409073C01
2.854,2.958 2.677,2.958 2.677,2.958 2.677,2.729 false 1.729,3 2.042,3.156 0.313,0.156 10 false *a 2.927,2.885 3.24,3.042 0.313,0.156 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, connect the accumulator to brake master cylinder tube to the brake booster pump assembly.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the accumulator to brake master cylinder tube.

·

Do not allow the accumulator to brake master cylinder tube to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the accumulator to brake master cylinder tube from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




Hide 44551C 6.CONNECT NO. 1 BRAKE ACTUATOR TUBE

a.
C407893

Install the No. 1 brake actuator tube with the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 44572C 7.CONNECT NO. 2 BRAKE ACTUATOR HOSE

a.
C409071C02
1.906,1.146 2.292,1.563 2.292,1.563 2.5,1.563 true 2.542,1.458 2.76,1.656 0.219,0.198 10 true *a 2.333,2.042 2.667,2.365 0.333,0.323 10 false 30° 1.865,2.031 2.156,2.302 0.292,0.271 10 false 30°
*a Identification Mark
V100136

Up


Connect the No. 2 brake actuator hose to the No. 1 brake actuator tube and slide the clip to secure it.

NOTICE:
·

When connecting the No. 2 brake actuator hose, face the identification mark toward the up of the vehicle.

·

Install the clip within the range shown in the illustration.




Hide 47220D 8.SEPARATE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

a.
C407873

Remove the 2 nuts and separate the brake master cylinder reservoir assembly from the reservoir bracket.


Hide 47220D 10.INSTALL BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

Hide 11.FILL RESERVOIR WITH BRAKE FLUID

Hide 12.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Click hereBrake>BRAKE (REAR)>REAR BRAKE>INSTALLATION

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 55704B 14.INSTALL COWL VENTILATOR PANEL SUB-ASSEMBLY

Hide 15.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY