Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for RHD without Vacuum Brake Booster)
RM3620E _54 Brake _076411 BRAKE SYSTEM (OTHER) _0377040 BRAKE BOOSTER(for RHD without Vacuum Brake Booster) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for RHD without Vacuum Brake Booster)  INSTALLATION  


PROCEDURE

Hide 44785C 1.INSTALL BRAKE BOOSTER GASKET

a.

Install a new brake booster gasket to the brake booster with master cylinder assembly.


Hide 47210L 2.INSTALL BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

a.
C407886C02
1.719,2.646 2.219,2.646 false 1.438,3.833 0.75,4.125 0.75,4.125 1.385,4.125 true 1.719,3.063 0.583,2.583 0.583,2.583 1.313,3.094 true 2.74,3.469 2.917,3.677 2.917,3.677 3.083,3.677 false 2.406,3.583 2.698,3.938 2.698,3.938 2.865,3.938 false 2.281,2.583 2.594,2.74 0.313,0.156 10 false *1 0.396,2.469 0.708,2.625 0.313,0.156 10 false *2 3.146,3.615 3.427,3.823 0.281,0.208 10 false *3 2.917,3.854 3.229,4.01 0.313,0.156 10 false *4 0.563,4.042 0.875,4.198 0.313,0.156 10 false *5
*1 Connector Portion
*2 Union
*3 Push Rod Clevis
*4 Boot
*5 Front No. 2 Brake Tube


Install the brake booster with master cylinder assembly with the 4 nuts.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not carry the brake booster with master cylinder assembly by the portion shown in the illustration.

·

Be careful not to allow brake fluid to enter the connector of ECU.

·

If installing a new brake booster with master cylinder assembly, do not remove the hole plugs before connecting the brake lines because the brake booster with master cylinder is filled with brake fluid.




b.
C407882

Engage the clamp to connect the suction pipe sub-assembly.


c.
C407881

Connect the brake tube clamp bracket with the bolt.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


d.
C407880

Engage the clamp and install a new brake tube clamp to the brake tube clamp bracket.


e.
C407879

Engage the grommet and connect the front No. 3 brake tube.


f.
C409065C01
2.792,3.083 2.625,3.083 2.625,3.083 2.625,2.75 false 1.677,3.01 2.01,3.292 0.333,0.281 10 false *a 2.844,3 3.083,3.198 0.24,0.198 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Temporarily install the front No. 3 brake tube to the front flexible hose.

NOTICE:
·

Do not kink or damage the front No. 3 brake tube.

·

Do not allow any foreign matter such as dirt or dust to enter the front No. 3 brake tube from the connecting parts.




g.

Using a union nut wrench, tighten the front No. 3 brake tube.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Do not kink or damage the brake line.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




h.
C407877

Engage the clamp to connect the brake tube to the brake tube clamp.


i.
C407885

Engage the clamp and install a new brake tube clamp to the vehicle body.


j.

Engage the 4 clamps to connect the brake tube clamp to the brake lines.


k.
C407884

Engage the clamp and install a new brake tube clamp to the brake booster with master cylinder assembly.


l.

Engage the 4 clamps to connect the brake tube clamp to the brake lines.


m.
C407883

Engage the 4 clamps to install the brake tube clamp to the brake lines.


n.
C407876C02
1.167,0.708 0.917,0.375 0.917,0.375 0.75,0.375 true 1.229,1.365 1.125,1.917 1.125,1.917 0.833,1.917 true 1.24,1.167 1.677,1.406 1.677,1.406 1.865,1.406 true 2.146,0.729 2.313,0.146 2.313,0.146 2.531,0.146 true 1.177,0.969 0.865,0.74 0.865,0.74 0.698,0.74 true 0.531,0.271 0.771,0.49 0.24,0.219 10 true *a 0.531,0.656 0.75,0.854 0.219,0.198 10 true *b 1.938,1.333 2.167,1.531 0.229,0.198 10 true *c 0.667,1.844 0.896,2.052 0.229,0.208 10 true *d 2.594,0.063 2.875,0.24 0.281,0.177 10 true *e
*a To Front Wheel Cylinder LH
*b To Rear Wheel Cylinder RH
*c To Brake Booster Pump Assembly
*d To Rear Wheel Cylinder LH
*e To Front Wheel Cylinder RH


Temporarily install each brake line to the correct position on the brake booster with master cylinder assembly as shown in the illustration.

NOTICE:
·

Do not kink or damage the brake line.

·

Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.




o.
C407889C02
2.917,3 2.75,3 2.75,3 2.75,2.667 false 1.75,2.948 2.063,3.104 0.313,0.156 10 false *a 2.979,2.927 3.24,3.115 0.26,0.188 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, tighten each brake line.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Do not kink or damage the brake line.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




p.
C407887C01
0,0 0,0 false
V113147

Connect the connector
V113148

Lock the lock lever


Connect the connector to the brake booster with master cylinder assembly.

NOTICE:
·

Make sure that the connector can be connected smoothly. Do not allow water, oil or dirt to enter.

·

Make sure that the connector lock is locked securely.




q.

Engage the clamp.


Hide 47233 3.INSTALL RESERVOIR BRACKET

a.
C407874

Install the reservoir bracket to the vehicle body with the bolt and 2 nuts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 4.CONNECT BRAKE MASTER CYLINDER RESERVOIR WITH RESERVOIR HOSE

a.

Connect the brake master cylinder reservoir with reservoir hose to the reservoir bracket.


b.
C407888C01
1.948,0.208 2.406,0.406 0.458,0.198 10 false 90° 0.99,0.208 1.448,0.406 0.458,0.198 10 false 90°
V100136

Up


Connect the 3 hoses and slide the clip to secure it.

NOTICE:
·

Make sure to match the identification mark on the 3 reservoir hoses and brake booster with master cylinder assembly.

·

When connecting the 3 reservoir hoses, face the identification mark up.

·

Make sure to install the hose to the proper location.

·

Install the clip within the range shown in the illustration.




Hide 44551 5.BLEED NO. 1 BRAKE ACTUATOR TUBE

a.

Add brake fluid into the reservoir.


b.
C407890C01
3,1.563 3,1.313 true 2.927,1.594 3.177,1.792 0.25,0.198 10 true *1
*1 No. 1 Brake Actuator Tube


Lift up the brake master cylinder reservoir assembly as far as possible and rock it back and forth to bleed air from the No. 1 brake actuator tube.

NOTICE:
·

Do not damage the hoses.

·

Do not spill brake fluid.

·

Continue this procedure until only a minor amount of air remains in the brake actuator tube.




Hide 47220D 6.INSTALL BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

a.
C407873

Install the brake master cylinder reservoir assembly to the reservoir bracket with the 2 nuts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 8.CONNECT WIRE HARNESS

a.
C409064

Engage the 2 clamps to connect the wire harness to the brake pedal support assembly.


b.

Connect the connector to the brake pedal stroke sensor assembly.


Hide 84340 10.INSTALL STOP LIGHT SWITCH ASSEMBLY

Hide 87211A 11.INSTALL NO. 2 AIR DUCT

Hide 73900 12.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 13.FILL RESERVOIR WITH BRAKE FLUID

Hide 14.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 55704B 17.INSTALL COWL VENTILATOR PANEL SUB-ASSEMBLY

Hide 18.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

HINT:

Use the same procedure as for LHD.

Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>INSTALLATION


Hide 19.PERFORM INITIALIZATION AND CALIBRATION OF LINEAR SOLENOID VALVE AND ZERO POINT OF YAW RATE AND ACCELERATION SENSOR