Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)
RM3620E _54 Brake _076410 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0379312 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster)  C1210  Zero Point Calibration of Yaw Rate Sensor Undone  C1336  Zero Point Calibration of Deceleration Sensor undone  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via CAN communication.

The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition using 2 circuits (GL1, GL2).

HINT:

If there are malfunctions in the bus lines between the yaw rate and acceleration sensor (airbag sensor assembly) and the CAN communication system, DTCs U0123 (Lost Communication with Yaw Rate Sensor Module) and U0124 (Lost Communication with Lateral Acceleration Sensor Module) will be stored.


These DTCs (C1210 and C1336) will also be stored when zero point calibration has not been completed.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1210 Zero Point Calibration of Yaw Rate Sensor Undone - Yaw rate sensor zero point calibration is incomplete.
·

Zero point calibration undone

·

Yaw rate sensor (Airbag sensor assembly)

·

Skid control ECU (Brake booster with master cylinder assembly)


(Perform zero point calibration and check for DTCs. If no DTCs are output again, the sensor is normal.)
-
C1336 Zero Point Calibration of Deceleration Sensor undone - Either of the following is detected:
1.

The vehicle is driven normally without zero point calibration completed.

2.

After completing zero point calibration, zero point voltage of the sensor is not within the range of 2.38 to 2.62 V.


·

Zero point calibration undone

·

Acceleration sensor (Airbag sensor assembly)

·

Skid control ECU (Brake booster with master cylinder assembly)


(Perform zero point calibration and check for DTCs. If no DTCs are output again, the sensor is normal.)
-

DTC Detection Conditions: C1336
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition - - -
Malfunction Status The vehicle is driven normally without zero point calibration completed ○ -
After completing zero point calibration, zero point voltage of the sensor is not within the range of 2.38 to 2.62 V - ○
Detection Time - -
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>UTILITY

·

When replacing the yaw rate and acceleration sensor (airbag sensor assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>UTILITY



HINT:

When U0123 and/or U0124 is output together with C1210 and/or C1336, inspect and repair trouble areas indicated by U0123 and/or U0124 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>U0073


PROCEDURE

1.PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR
a.

Perform zero point calibration of the yaw rate and acceleration sensor.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>UTILITY

Chassis > ABS/VSC/TRC > Utility
Tester Display
Test Mode
50005 105 1166

Result:
Proceed to
NEXT



NEXT

2.RECONFIRM DTC
2.RECONFIRM DTC
a.

Turn the power switch off.



c.

Turn the power switch off.


d.

Turn the power switch on (READY).


e.

Drive the vehicle at a speed of 30 km/h (18 mph) or more, turn the steering wheel, and decelerate the vehicle (depress the brake pedal).


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTCs C1210 and/or C1336 are output. A
DTCs C1210 and C1336 are not output. B


HINT:
·

These DTCs are stored because zero point calibration has not been completed.

·

End the procedure if the same DTCs are not stored after completion of zero point calibration.





A

3.CHECK AIRBAG SENSOR ASSEMBLY

B

END

3.CHECK AIRBAG SENSOR ASSEMBLY
a.

Turn the power switch off.


b.

Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION

OK:

The airbag sensor assembly is tightened to the specified torque.

The airbag sensor assembly is not tilted.



Result:
Proceed to
OK
NG



OK

4.REPLACE AIRBAG SENSOR ASSEMBLY

NG

4.REPLACE AIRBAG SENSOR ASSEMBLY
a.

Replace the yaw rate and acceleration sensor (airbag sensor assembly).

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL

NOTICE:

Check the yaw rate and acceleration sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>TEST MODE PROCEDURE



Result:
Proceed to
NEXT



NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC

b.

Turn the power switch off.


c.

Turn the power switch on (READY).


d.

Drive the vehicle at a speed of 30 km/h (18 mph) or more, turn the steering wheel, and decelerate the vehicle (depress the brake pedal).


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs C1210 and/or C1336 are output. A
DTCs C1210 and C1336 are not output. B



A

B

END