Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)
RM3620E _54 Brake _076410 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0379312 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster)  C1271  Low Output Signal of Front Speed Sensor RH (Test Mode DTC)  C1272  Low Output Signal of Front Speed Sensor LH (Test Mode DTC)  C1464  Front Speed Sensor RH Circuit  C1465  Front Speed Sensor LH Circuit  


DESCRIPTION

Each speed sensor detects the wheel speed and sends the signals to the skid control ECU (brake booster with master cylinder assembly). These signals are used for ABS control.

DTCs C1271 and C1272 are cleared when the speed sensor sends a wheel speed signal or when Test Mode ends. DTCs C1271 and C1272 are output only in Test Mode.

C223506E02
1.281,1.063 1.281,0.708 1.281,0.708 1.073,0.708 false 0.156,0.604 1.344,0.917 1.188,0.313 10 Speed Sensor 4.938,1.917 5.781,2.104 0.844,0.188 10 High speed 4.01,1.917 4.792,2.104 0.781,0.188 10 Low speed 6.052,1.156 6.51,1.427 0.458,0.271 10 1.4 V 6.052,1.49 6.542,1.813 0.49,0.323 10 0.7 V 0.906,2.177 2.365,2.385 1.458,0.208 10 Speed Sensor Rotor

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1271 Low Output Signal of Front Speed Sensor RH (Test Mode DTC) - Detected only during Test Mode.
·

Front speed sensor RH

·

Sensor installation

·

Front speed sensor rotor RH (Front axle hub sub-assembly RH)


-
C1272 Low Output Signal of Front Speed Sensor LH (Test Mode DTC) - Detected only during Test Mode.
·

Front speed sensor LH

·

Sensor installation

·

Front speed sensor rotor LH (Front axle hub sub-assembly LH)


-
C1464 Front Speed Sensor RH Circuit 501
502
503
504
506
507
508
509
·

INF Code: 501

-

At a vehicle speed of 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from other wheels for 15 seconds or more.



·

INF Code: 502

-

At a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) for 15 seconds or more.



·

INF Code: 503

-

An open is detected in the speed sensor signal circuit for 0.5 seconds or more.



·

INF Code: 504

-

Instantaneous interruption of sensor signal from the malfunctioning wheel occurs 255 times or more.



·

INF Code: 506

-

When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 0.5 seconds or more.



·

INF Code: 507

-

At a vehicle speed of 10 km/h (6 mph) or more, speed sensor output from one wheel is 0 km/h (0 mph) for 1 second or more.



·

INF Code: 508

-

When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 60 seconds or more.



·

INF Code: 509

-

Speed sensor output is 270 km/h (167 mph) or more continuously for 5 seconds or more.



·

INF Code: 501, 502, 504, 507

-

Open or short in speed sensor


-

Improperly installed speed sensor, or abnormal clearance between sensor and rotor


-

Open or short in wire harness


-

Improperly connected connector, deformation or corrosion of terminals


-

Front speed sensor RH


-

Skid control ECU (Brake booster with master cylinder assembly)



·

INF Code: 503

-

Open or short in speed sensor


-

Open or short in wire harness


-

Improperly connected connector, deformation or corrosion of terminals


-

Front speed sensor RH


-

Skid control ECU (Brake booster with master cylinder assembly)



·

INF Code: 506, 508

-

Open or short in wire harness


-

Skid control ECU (Brake booster with master cylinder assembly)



·

INF Code: 509

-

Open or short in speed sensor


-

Open or short in wire harness


-

Front speed sensor RH


-

Skid control ECU (Brake booster with master cylinder assembly)



-
C1465 Front Speed Sensor LH Circuit 511
512
513
514
516
517
518
519
·

INF Code: 511

-

At a vehicle speed of 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from other wheels for 15 seconds or more.



·

INF Code: 512

-

At a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) for 15 seconds or more.



·

INF Code: 513

-

An open is detected in the speed sensor signal circuit for 0.5 seconds or more.



·

INF Code: 514

-

Instantaneous interruption of sensor signal from the malfunctioning wheel occurs 255 times or more.



·

INF Code: 516

-

When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 0.5 seconds or more.



·

INF Code: 517

-

At a vehicle speed of 10 km/h (6 mph) or more, speed sensor output from one wheel is 0 km/h (0 mph) for 1 second or more.



·

INF Code: 518

-

When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 60 seconds or more.



·

INF Code: 519

-

Speed sensor output is 270 km/h (167 mph) or more continuously for 5 seconds or more.



·

INF Code: 511, 512, 514, 517

-

Open or short in speed sensor


-

Improperly installed speed sensor, or abnormal clearance between sensor and rotor


-

Open or short in wire harness


-

Improperly connected connector, deformation or corrosion of terminals


-

Front speed sensor LH


-

Skid control ECU (Brake booster with master cylinder assembly)



·

INF Code: 513

-

Open or short in speed sensor


-

Open or short in wire harness


-

Improperly connected connector, deformation or corrosion of terminals


-

Front speed sensor LH


-

Skid control ECU (Brake booster with master cylinder assembly)



·

INF Code: 516, 518

-

Open or short in wire harness


-

Skid control ECU (Brake booster with master cylinder assembly)



·

INF Code: 519

-

Open or short in speed sensor


-

Open or short in wire harness


-

Front speed sensor LH


-

Skid control ECU (Brake booster with master cylinder assembly)



-

WIRING DIAGRAM

C326772E10
0.781,1.854 1.24,2.052 0.458,0.198 10 false A91 0.729,2.073 2.365,2.354 1.635,0.281 10 false Front Speed Sensor RH 0.854,1.427 1.313,1.625 0.458,0.198 10 false 1 2.042,1.427 2.5,1.625 0.458,0.198 10 false 2 1.052,1.542 1.51,1.74 0.458,0.198 10 false FR+ 1.698,1.542 2.156,1.74 0.458,0.198 10 false FR- 5.625,0.833 6.083,1.031 0.458,0.198 10 false 18 5.625,1.417 6.083,1.615 0.458,0.198 10 false 5 5.896,0.833 6.354,1.031 0.458,0.198 10 false FR+ 5.896,1.427 6.354,1.625 0.458,0.198 10 false FR- 5.625,2.594 6.083,2.792 0.458,0.198 10 false 31 5.635,3.188 6.094,3.385 0.458,0.198 10 false 32 5.896,2.594 6.354,2.792 0.458,0.198 10 false FL+ 5.896,3.198 6.354,3.396 0.458,0.198 10 false FL- 0.896,3.875 2.5,4.5 1.604,0.625 10 false Front Speed Sensor LH 0.865,3.656 1.323,3.854 0.458,0.198 10 false A92 1.063,3.313 1.521,3.51 0.458,0.198 10 false FL+ 1.698,3.313 2.156,3.51 0.458,0.198 10 false FL- 2.052,3.198 2.51,3.396 0.458,0.198 10 false 2 0.844,3.208 1.302,3.406 0.458,0.198 10 false 1 4.969,4.073 7.115,4.552 2.146,0.479 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 4.906,3.885 5.365,4.083 0.458,0.198 10 false A42

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>UTILITY


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruptions in the wire harness and connector corresponding to a DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>CHECK FOR INTERMITTENT PROBLEMS

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Speed Open Front speed sensor RH open detection Error or Normal Error: Momentary interruption detected
Normal: Momentary interruption not detected
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal".
FL Speed Open Front speed sensor LH open detection Error or Normal Error: Momentary interruption detected
Normal: Momentary interruption not detected
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal".
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Speed Open
FL Speed Open
50003 105 200,201
OK:

Normal (There are no momentary interruptions.)


HINT:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (FRONT SPEED SENSOR)

NG

5.CHECK FRONT SPEED SENSOR INSTALLATION
2.READ VALUE USING GTS (FRONT SPEED SENSOR)
a.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front speed sensor RH Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front speed sensor LH Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Wheel Speed
FL Wheel Speed
50003 105 1,2

b.

Check the speed value output from the speed sensor displayed on the GTS.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK


OK:

The speed value output from the speed sensor displayed on the GTS is similar to the speed indicated on the speedometer.



Result:
Proceed to
OK
NG



OK

3.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)

NG

5.CHECK FRONT SPEED SENSOR INSTALLATION
3.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
a.

Turn the power switch off.


b.

Perform the sensor check in Test Mode Procedure.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>TEST MODE PROCEDURE

Chassis > ABS/VSC/TRC > Utility
Tester Display
Signal Check
50005 105 1003
OK:

All Test Mode DTCs are cleared.



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

5.CHECK FRONT SPEED SENSOR INSTALLATION
4.RECONFIRM DTC
a.

Turn the power switch off.



c.

Turn the power switch on (READY).


d.

Perform a road test.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTCs C1464 and C1465 are not output. A
DTCs C1464 and/or C1465 are output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>PROBLEM SYMPTOMS TABLE




A

B

7.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - FRONT SPEED SENSOR)
5.CHECK FRONT SPEED SENSOR INSTALLATION
a.
C168336C26
0.906,1.49 1.26,1.854 false 0.688,0.385 1,0.583 0.313,0.198 10 false *b 2.26,0.385 2.573,0.583 0.313,0.198 10 false *c 1.406,1.885 1.719,2.083 0.313,0.198 10 false *a
*a No clearance
*b OK
*c NG


Turn the power switch off.


b.

Check the speed sensor installation.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>INSTALLATION

OK:

There is no clearance between the sensor and the front steering knuckle.

The installation bolt is tightened properly.



Result:
Proceed to
OK
NG



OK

6.CHECK FRONT SPEED SENSOR AND SENSOR ROTOR

NG

6.CHECK FRONT SPEED SENSOR AND SENSOR ROTOR
a.

Remove the front speed sensor and the component with the speed sensor rotor.

for Speed Sensor: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL

for Speed Sensor Rotor: Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL


b.

Check the speed sensor tip and speed sensor rotor.

OK:

The sensor tip and rotor are free of scratches, oil, and foreign matter.


NOTICE:
·

If there are any ferrous metal filings stuck to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign matter before replacing the sensor.

·

If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.




Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - FRONT SPEED SENSOR)

NG

CLEAN OR REPLACE REAR SPEED SENSOR OR COMPONENT WITH SENSOR ROTOR

7.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - FRONT SPEED SENSOR)

b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Disconnect the A91 or A92 front speed sensor connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A42-18 (FR+) - A91-1 (FR+) Always Below 1 Ω
A42-18 (FR+) or A91-1 (FR+) - Body ground Always 10 kΩ or higher
A42-5 (FR-) - A91-2 (FR-) Always Below 1 Ω
A42-5 (FR-) or A91-2 (FR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A42-31 (FL+) - A92-1 (FL+) Always Below 1 Ω
A42-31 (FL+) or A92-1 (FL+) - Body ground Always 10 kΩ or higher
A42-32 (FL-) - A92-2 (FL-) Always Below 1 Ω
A42-32 (FL-) or A92-2 (FL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)
a.
C408616C04
0.74,0.26 1.229,0.552 0.49,0.292 2.229,0.271 2.719,0.563 0.49,0.292 1.135,1.135 1.479,1.521 true 2.615,1.146 2.958,1.531 true 0.135,0.083 0.323,0.24 0.188,0.156 10 false *a 2.344,0.333 2.635,0.49 0.292,0.156 10 false A92 0.844,0.323 1.292,0.521 0.448,0.198 10 false A91 0.49,0.354 0.802,0.552 0.313,0.198 10 false *A 1.969,0.385 2.281,0.583 0.313,0.198 10 false *B 2.927,1.573 3.292,1.792 0.365,0.219 10 false FL+ 1.406,1.573 1.771,1.792 0.365,0.219 10 false FR+
*A for RH
*B for LH
*a Front view of wire harness connector
(to Front Speed Sensor)


Reconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Condition Specified Condition
A91-1 (FR+) - Body ground2 Power switch on (IG) 5.7 to 14 V

for LH
Tester Connection Condition Specified Condition
A92-1 (FL+) - Body ground Power switch on (IG) 5.7 to 14 V



Result:
Proceed to
OK
NG



OK

NG