The skid control ECU (brake booster with master cylinder assembly) controls braking force according to the hybrid control system regenerative braking force and provides the hydraulic pressure necessary for operating each wheel cylinder according to the wheel cylinder pressure sensor.
DTCs may be stored if one of the following occurs:
Brake fluid leaks.
Wheel cylinder vibrates due to uneven wear of a brake disc.
Foreign matter enters a solenoid valve.
Line pressure drops during air bleeding.
Brake pads are replaced.
Rotors are replaced.
When replacing the brake pads, retracting the brake caliper pistons and installing new brake pads will greatly increase the clearance between the brake pads and brake discs. This will result in a significant possibility of this DTC being stored the next time the brake pedal is depressed. As this is not a malfunction, clear the DTC if it is stored for this reason.
| DTC No. | Detection Item | INF Code | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|---|
| C1214 | Hydraulic Control System Malfunction | 431
432 433 434 435 436 437 438 |
·
INF Code: 431 -
Decrease in hydraulic pressure control performance. (Pressure increase malfunction) ·
INF Code: 432 -
Decrease in hydraulic pressure control performance. (Pressure decrease malfunction) ·
INF Code: 433 -
Malfunctions such as leaks occur in the SLA valve. ·
INF Code: 434, 435 -
Malfunctions such as leaks occur in the SLR valve. ·
INF Code: 436, 437 -
Decrease in hydraulic pressure control performance. ·
INF Code: 438 -
Malfunctions such as leaks occur in a hydraulic circuit valve. |
·
INF Code: 431, 432, 433, 434, 435, 436, 437 -
Brake fluid leaks -
Brake disc rotor excessive wear -
Brake actuator (Brake booster with master cylinder assembly) ·
INF Code: 438 -
Brake actuator (Brake booster with master cylinder assembly) |
- |
When replacing the brake actuator (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.
When C1364 is output together with C1214, inspect and repair the trouble areas indicated by C1364 first.
Check that there are no fluid leaks in the brake lines between the brake actuator (brake booster with master cylinder assembly) and the wheel cylinders.
Check that the brakes are not dragging.
There are no fluid leaks or dragging.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector 2 minutes after the power switch is turned off.
Check both the connector body and the terminals for deformation and corrosion.
No deformation or corrosion.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD without Vacuum Brake Booster)>REMOVAL
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD without Vacuum Brake Booster)>REMOVAL
Reconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.
Clear the DTCs.
Perform the air bleeding procedure in Bleed Brake System.
Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (w/o Vacuum Brake Booster)>BLEEDING
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.
Measure the voltage and resistance on the wire harness side.
Voltage and resistance readings are all normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.
Connect an LSPV gauge set.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Select the Data List on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Wheel Cylinder Pressure Sensor | Wheel cylinder pressure sensor | Min.: 0.00 V, Max.: 5.00 V | Brake pedal released: 0.10 to 0.90 V | Reading increases when brake pedal is depressed |
| Tester Display |
|---|
| Wheel Cylinder Pressure Sensor |
Check the output values of the wheel cylinder pressure sensor at each hydraulic pressure level during electronically controlled brake system control.
| Hydraulic Pressure
(MPa (kgf/cm2, psi)) |
Wheel Cylinder Pressure Sensor
(V) |
|---|---|
| 2.0 (20.4, 290) | 0.53 to 1.33 |
| 5.0 (51.0, 725) | 1.12 to 1.92 |
| 7.0 (71.4, 1015) | 1.52 to 2.32 |
| 10.0 (102.0, 1451) | 2.14 to 2.94 |
| Hydraulic Pressure
(MPa (kgf/cm2, psi)) |
Wheel Cylinder Pressure Sensor
(V) |
|---|---|
| 2.0 (20.4, 290) | 0.53 to 1.33 |
| 5.0 (51.0, 725) | 1.12 to 1.92 |
| 7.0 (71.4, 1015) | 1.52 to 2.32 |
| 10.0 (102.0, 1451) | 2.14 to 2.94 |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD without Vacuum Brake Booster)>REMOVAL
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD without Vacuum Brake Booster)>REMOVAL
Turn the power switch off.
Disconnect the A41 brake pedal stroke sensor assembly connector.
Perform a road test according to Freeze Frame Data or customer problem analysis. While driving, check for abnormal brake pedal vibration caused by brake discs that are worn or have excess runout.
Brake pedal does not vibrate during braking.
An unevenly worn disc may vibrate the caliper piston and cause fluctuations in brake line pressure, triggering a malfunction detection condition.
The brake pedal does not kick back due to caliper piston vibration during electronically controlled brake system control.
If the brake pedal stroke sensor assembly connector is disconnected, the fail-safe function will prohibit electronically controlled brake system control.
The Active Test does not prohibit electronically controlled brake system control when the vehicle is being driven, so disconnect the brake pedal stroke sensor assembly connector before continuing with inspection.
Uneven disc wear can be checked by measuring the disc thickness variation.
for Front Brake (for 2-Pot Caliper): Click hereBrake>BRAKE (FRONT)>FRONT BRAKE (for 2-Pot Caliper)>INSPECTION
for Front Brake (except 2-Pot Caliper): Click hereBrake>BRAKE (FRONT)>FRONT BRAKE (except 2-Pot Caliper)>INSPECTION
for Rear Brake: Click hereBrake>BRAKE (REAR)>REAR BRAKE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the A41 brake pedal stroke sensor assembly connector.
Clear the DTCs.
Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| DTC C1214 is not output. | A |
| DTC C1214 is output. | B |
If the DTC is no longer output, it can be suspected that it was output due to an improperly connected connector.
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD without Vacuum Brake Booster)>REMOVAL
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD without Vacuum Brake Booster)>REMOVAL