Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)
RM3620E _54 Brake _076410 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0379312 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster)  C1246  Master Cylinder Pressure Sensor  C1281  Abnormal Output in Master Cylinder Pressure Sensor  C1364  Wheel Cylinder Pressure Sensor  


DESCRIPTION

The regulator pressure sensor and wheel cylinder pressure sensor are built into the brake actuator. They measure their respective pressures and send signals to the skid control ECU (brake booster with master cylinder assembly).

DTC C1281 will be cleared when the regulator pressure sensor sends a regulator pressure signal or when Test Mode ends. DTC C1281 is output only in Test Mode.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1246 Master Cylinder Pressure Sensor 201
202
203
204
207
·

INF Code: 201

-

Sensor supply voltage (VCM1) is 4.75 V or less, or 5.25 V or more for 0.05 seconds.


·

INF Code: 202

-

Regulator pressure sensor output voltage (Preg) is less than 8%, or 90.3% or more (less than 0.4 V, or 4.52 V or more) of sensor supply voltage (VCM1) for 0.05 seconds or more.


·

INF Code: 203

-

When not under braking, the regulator pressure sensor output voltage is 0.2 V or less or 0.88 V or more for 3 seconds or more.


·

INF Code: 204

-

Either of the following is detected:

(1)

The regulator pressure sensor output voltage does not correspond with brake pedal stroke sensor assembly and the readings remain out of specification for 0.5 to 5 seconds or more continuously.

(The brake pedal stroke sensor assembly may be malfunctioning.)

(2)

The regulator pressure sensor output voltage does not correspond with wheel cylinder pressure sensor and the outputs remain out of specification for 0.5 to 5 seconds or more continuously.

(May be output with INF code 424.)



·

INF Code: 207

-

Fluctuation of regulator pressure sensor output is out of specification (the difference between the present value and last value is 15 MPa (153.0 kgf/cm2, 2176 psi) or more) for 0.1 seconds or more.



·

INF Code: 201, 202, 203, 207

-

Brake booster with master cylinder assembly


·

INF Code: 204

-

Brake pedal stroke sensor assembly

-

Brake booster with master cylinder assembly



-
C1281 Abnormal Output in Master Cylinder Pressure Sensor - Detected only during Test Mode.
·

Stop light switch assembly

·

Regulator pressure sensor (Brake booster with master cylinder assembly)


-
C1364 Wheel Cylinder Pressure Sensor 421
422
423
424
426
·

INF Code: 421

-

Sensor supply voltage 1 (VCM1) is 4.75 V or less, or 5.25 V or more for 0.05 seconds or more.


·

INF Code: 422

-

Wheel cylinder pressure sensor output voltage (Pfront) is less than 8%, or 90.3% or more (less than 0.4 V, or 4.52 V or more) of sensor supply voltage (VCM1) for 0.05 seconds or more.


·

INF Code: 423

-

When not under braking, the wheel cylinder pressure sensor output voltage is 0.2 V or less or 0.88 V or more for 0.1 to 3 seconds or more.


·

INF Code: 424

-

The wheel cylinder pressure sensor output voltage does not correspond with regulator pressure sensor and the outputs remain out of specification for 0.5 to 5 seconds or more continuously.

(May be output with INF code 204.)


·

INF Code: 426

-

Fluctuation of wheel cylinder pressure sensor output is out of specification (the difference between the present value and last value is 15 MPa (153.0 kgf/cm2, 2176 psi) or more) for 0.1 seconds or more.



Brake booster with master cylinder assembly -

DTC Detection Conditions: C1246 INF Code: 204
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition - - -
Malfunction Status The regulator pressure sensor output voltage does not correspond with brake pedal stroke sensor assembly and the readings remain out of specification for 0.5 to 5 seconds or more continuously (The brake pedal stroke sensor assembly may be malfunctioning) ○ -
The regulator pressure sensor output voltage does not correspond with wheel cylinder pressure sensor and the outputs remain out of specification for 0.5 to 5 seconds or more continuously (May be output with INF code 424) - ○
Detection Time - -
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly) or brake actuator (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>UTILITY


PROCEDURE

1.CHECK STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Check the protrusion of the plunger.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION

OK:

The stop light switch assembly is installed properly.


HINT:

If the stop light switch assembly is not installed properly, adjust the protrusion of the plunger before proceeding to the next step.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (REGULATOR PRESSURE SENSOR)

NG

2.READ VALUE USING GTS (REGULATOR PRESSURE SENSOR)
a.

Mount a pedal effort gauge and install LSPV gauges to the rear wheels.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE SYSTEM (w/o Vacuum Brake Booster)>ON-VEHICLE INSPECTION


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Regulator Pressure Sensor Output Regulator pressure sensor output Min.: 0.00 V, Max.: 5.00 V Brake pedal released: 0.10 to 0.90 V Reading increases when brake pedal is depressed
Chassis > ABS/VSC/TRC > Data List
Tester Display
Regulator Pressure Sensor Output
50003 105 307

e.

Check the output value of the regulator pressure sensor as the brake pedal is depressed.

Standard Voltage:
Brake Effort
(N (kgf, lbf))
Regulator Pressure Sensor Output
(V)
Rear Right Wheel Hydraulic Pressure
(MPa (kgf/cm2, psi))
Rear Left Wheel Hydraulic Pressure
(MPa (kgf/cm2, psi))
100 (10, 22.5) 1.60 to 2.40 5.33 to 9.33 (54.4 to 95.1, 773 to 1352) 5.33 to 9.33 (54.4 to 95.1, 773 to 1352)
200 (20, 45.0) 3.58 to 4.38 15.06 to 19.06 (153.6 to 194.3, 2184 to 2763) 15.06 to 19.06 (153.6 to 194.3, 2184 to 2763)



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (WHEEL CYLINDER PRESSURE SENSOR)

NG

3.READ VALUE USING GTS (WHEEL CYLINDER PRESSURE SENSOR)

b.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Wheel Cylinder Pressure Sensor Wheel cylinder pressure sensor Min.: 0.00 V, Max.: 5.00 V Brake pedal released: 0.10 to 0.90 V Reading increases when brake pedal is depressed
Chassis > ABS/VSC/TRC > Data List
Tester Display
Wheel Cylinder Pressure Sensor
50003 105 308

c.

Check the output values of the wheel cylinder pressure sensor at each hydraulic pressure during electronically controlled brake system control.

Standard Voltage:
for Front Wheel Cylinder LH
Hydraulic Pressure
(MPa (kgf/cm2, psi))
Wheel Cylinder Pressure Sensor
(V)
2.0 (20.4, 290) 0.53 to 1.33
5.0 (51.0, 725) 1.12 to 1.92
7.0 (71.4, 1015) 1.52 to 2.32
10.0 (102.0, 1451) 2.14 to 2.94

for Front Wheel Cylinder RH
Hydraulic Pressure
(MPa (kgf/cm2, psi))
Wheel Cylinder Pressure Sensor
(V)
2.0 (20.4, 290) 0.53 to 1.33
5.0 (51.0, 725) 1.12 to 1.92
7.0 (71.4, 1015) 1.52 to 2.32
10.0 (102.0, 1451) 2.14 to 2.94



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (BRAKE PEDAL STROKE SENSOR ASSEMBLY AND PRESSURE SENSOR COMPARISON)

NG

4.READ VALUE USING GTS (BRAKE PEDAL STROKE SENSOR ASSEMBLY AND PRESSURE SENSOR COMPARISON)
a.

Mount a pedal effort gauge and install LSPV gauges to the front and rear wheels.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE SYSTEM (w/o Vacuum Brake Booster)>ON-VEHICLE INSPECTION


b.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Regulator Pressure Sensor Output Regulator pressure sensor output Min.: 0.00 V, Max.: 5.00 V Brake pedal released: 0.10 to 0.90 V Reading increases when brake pedal is depressed
Stroke Sensor Brake pedal stroke sensor assembly Min.: 0.00 V, Max.: 5.00 V Brake pedal released: 0.65 to 1.35 V Reading increases when brake pedal is depressed
Stroke Sensor2 Brake pedal stroke sensor assembly 2 Min.: 0.00 V, Max.: 5.00 V Brake pedal released: 3.65 to 4.35 V Reading decreases when brake pedal is depressed
Wheel Cylinder Pressure Sensor Wheel cylinder pressure sensor Min.: 0.00 V, Max.: 5.00 V Brake pedal released: 0.10 to 0.90 V Reading increases when brake pedal is depressed

Chassis > ABS/VSC/TRC > Data List
Tester Display
Regulator Pressure Sensor Output
Stroke Sensor
Stroke Sensor2
Wheel Cylinder Pressure Sensor
50003 105 307,11,12,308
c.

Check the output value of the brake pedal stroke sensor assembly as the brake pedal is depressed.

Standard Voltage:
Brake Effort
(N (kgf, lbf))
Stroke Sensor
(V)
Stroke Sensor2
(V)
Regulator Pressure Sensor Output
(V)
Wheel Cylinder Pressure Sensor
(V)
100 (10, 22.5) 1.66 to 2.36 2.64 to 3.34 1.60 to 2.40 1.38 to 2.18
200 (20, 45.0) 1.95 to 2.65 2.35 to 3.05 3.58 to 4.38 3.07 to 3.87



Result:
Proceed to
OK
NG



OK

5.RECONFIRM DTC

NG

5.RECONFIRM DTC

b.

Turn the power switch off.


c.

Perform a road test.


d.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs C1246 and C1364 are not output. A
DTCs C1246 and/or C1364 are output. B



A

B