Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster) › 2018.10–2019.02
RM3620E _54 Brake _076410 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0379312 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster)  C1273  Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)  C1274  Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)  C1466  Rear Speed Sensor RH Circuit  C1467  Rear Speed Sensor LH Circuit  


DESCRIPTION

Each speed sensor detects the wheel speed and sends the signals to the skid control ECU (brake booster with master cylinder assembly). These signals are used for ABS control.

DTCs C1273 and C1274 are cleared when the speed sensor sends a wheel speed signal or when Test Mode ends. DTCs C1273 and C1274 are output only in Test Mode.

C151818E35
1.573,0.854 1.573,0.469 1.573,0.469 1.667,0.469 false 1.74,0.385 2.854,0.76 1.115,0.375 10 false Speed Sensor 4.021,2.115 4.729,2.281 0.708,0.167 10 false Low speed 6.073,1.26 6.438,1.427 0.365,0.167 10 false 1.4 V 6.083,1.625 6.563,1.792 0.479,0.167 10 false 0.7 V 4.99,2.115 5.719,2.281 0.729,0.167 10 false High speed 0.969,2.177 2.26,2.344 1.292,0.167 10 false Speed Sensor Rotor

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1273 Low Output Signal of Rear Speed Sensor RH (Test Mode DTC) - Detected only during Test Mode.
·

Rear speed sensor RH (Rear axle hub and bearing assembly RH)

·

Sensor installation

·

Rear speed sensor rotor RH (Rear axle hub and bearing assembly RH)

·

Skid control sensor wire RH (No. 1 parking brake wire assembly)


-
C1274 Low Output Signal of Rear Speed Sensor LH (Test Mode DTC) - Detected only during Test Mode.
·

Rear speed sensor LH (Rear axle hub and bearing assembly LH)

·

Sensor installation

·

Rear speed sensor rotor LH (Rear axle hub and bearing assembly LH)

·

Skid control sensor wire LH (No. 2 parking brake wire assembly)


-
C1466 Rear Speed Sensor RH Circuit 521
522
523
524
526
527
528
529
·

INF Code: 521

-

At a vehicle speed of 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from other wheels for 15 seconds or more.



·

INF Code: 522

-

At a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) for 15 seconds or more.



·

INF Code: 523

-

An open is detected in the speed sensor signal circuit for 0.5 seconds or more.



·

INF Code: 524

-

Instantaneous interruption of sensor signal from the malfunctioning wheel occurs 255 times or more.



·

INF Code: 526

-

When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 0.5 seconds or more.



·

INF Code: 527

-

At a vehicle speed of 10 km/h (6 mph) or more, speed sensor output from one wheel is 0 km/h (0 mph) for 1 second or more.



·

INF Code: 528

-

When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 60 seconds or more.



·

INF Code: 529

-

Speed sensor output is 270 km/h (167 mph) or more continuously for 5 seconds or more.



·

INF Code: 521, 522, 524, 527

-

Open or short in speed sensor


-

Improperly installed speed sensor, or abnormal clearance between sensor and rotor


-

Open or short in wire harness


-

Improperly connected connector, deformation or corrosion of terminals


-

Rear speed sensor RH (Rear axle hub and bearing assembly RH)


-

Skid control ECU (Brake booster with master cylinder assembly)



·

INF Code: 523

-

Open or short in speed sensor


-

Open or short in wire harness


-

Improperly connected connector, deformation or corrosion of terminals


-

Rear speed sensor RH (Rear axle hub and bearing assembly RH)


-

Skid control ECU (Brake booster with master cylinder assembly)



·

INF Code: 526, 528

-

Open or short in wire harness


-

Skid control ECU (Brake booster with master cylinder assembly)



·

INF Code: 529

-

Open or short in speed sensor


-

Open or short in wire harness


-

Rear speed sensor RH (Rear axle hub and bearing assembly RH)


-

Skid control ECU (Brake booster with master cylinder assembly)



-
C1467 Rear Speed Sensor LH Circuit 531
532
533
534
536
537
538
539
·

INF Code: 531

-

At a vehicle speed of 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from other wheels for 15 seconds or more.



·

INF Code: 532

-

At a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) for 15 seconds or more.



·

INF Code: 533

-

An open is detected in the speed sensor signal circuit for 0.5 seconds or more.



·

INF Code: 534

-

Instantaneous interruption of sensor signal from the malfunctioning wheel occurs 255 times or more.



·

INF Code: 536

-

When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 0.5 seconds or more.



·

INF Code: 537

-

At a vehicle speed of 10 km/h (6 mph) or more, speed sensor output from one wheel is 0 km/h (0 mph) for 1 second or more.



·

INF Code: 538

-

When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 60 seconds or more.



·

INF Code: 539

-

Speed sensor output is 270 km/h (167 mph) or more continuously for 5 seconds or more.



·

INF Code: 531, 532, 534, 537

-

Open or short in speed sensor


-

Improperly installed speed sensor, or abnormal clearance between sensor and rotor


-

Open or short in wire harness


-

Improperly connected connector, deformation or corrosion of terminals


-

Rear speed sensor LH (Rear axle hub and bearing assembly LH)


-

Skid control ECU (Brake booster with master cylinder assembly)



·

INF Code: 533

-

Open or short in speed sensor


-

Open or short in wire harness


-

Improperly connected connector, deformation or corrosion of terminals


-

Rear speed sensor LH (Rear axle hub and bearing assembly LH)


-

Skid control ECU (Brake booster with master cylinder assembly)



·

INF Code: 536, 538

-

Open or short in wire harness


-

Skid control ECU (Brake booster with master cylinder assembly)



·

INF Code: 539

-

Open or short in speed sensor


-

Open or short in wire harness


-

Rear speed sensor LH (Rear axle hub and bearing assembly LH)


-

Skid control ECU (Brake booster with master cylinder assembly)



-

WIRING DIAGRAM

C410761E01
0.135,1.698 2.25,2.167 2.115,0.469 10 false Rear Speed Sensor RH (Rear Axle Hub and Bearing Assembly RH) 0.125,3.688 2.24,4.292 2.115,0.604 10 false Rear Speed Sensor LH (Rear Axle Hub and Bearing Assembly LH) 2.448,1.688 4.792,2.167 2.344,0.479 10 false Skid Control Sensor Wire RH (No. 1 Parking Brake Wire Assembly) 2.469,3.698 4.781,4.156 2.313,0.458 10 false Skid Control Sensor Wire LH (No. 2 Parking Brake Wire Assembly) 5.031,3.99 7.104,4.656 2.073,0.667 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 1.688,0.708 2.052,0.917 0.365,0.208 10 false RA+ 1.698,1.292 2.156,1.49 0.458,0.198 10 false RA- 1.667,2.667 2.125,2.865 0.458,0.198 10 false LA+ 1.698,3.229 2.156,3.427 0.458,0.198 10 false LA- 5.896,0.625 6.26,0.833 0.365,0.208 10 false RR+ 5.906,1.156 6.365,1.354 0.458,0.198 10 false RR- 5.896,2.563 6.354,2.76 0.458,0.198 10 false RL+ 5.906,3.104 6.365,3.302 0.458,0.198 10 false RL- 2.073,0.719 2.375,0.938 0.302,0.219 10 false M50 4.115,0.719 4.49,0.938 0.375,0.219 10 false MM2 2.094,2.667 2.479,2.885 0.385,0.219 10 false N58 4.135,2.667 4.458,2.865 0.323,0.198 10 false NN2 2.094,1.281 2.406,1.5 0.313,0.219 10 false M50 5.635,0.604 5.948,0.802 0.313,0.198 10 false 22 5.677,1.125 5.99,1.323 0.313,0.198 10 false 9 5.635,2.542 5.948,2.74 0.313,0.198 10 false 20 5.698,3.073 6.01,3.271 0.313,0.198 10 false 7 2.177,0.458 2.354,0.667 0.177,0.208 10 false 2 4.219,1.052 4.396,1.26 0.177,0.208 10 false 4 4.229,0.521 4.406,0.729 0.177,0.208 10 false 3 2.219,1.052 2.396,1.26 0.177,0.208 10 false 1 4.229,2.427 4.406,2.635 0.177,0.208 10 false 3 4.219,3 4.396,3.208 0.177,0.208 10 false 4 2.177,2.427 2.354,2.635 0.177,0.208 10 false 2 2.177,2.969 2.354,3.177 0.177,0.208 10 false 1 5.031,3.771 5.344,3.969 0.313,0.198 10 false A42 2.094,3.219 2.469,3.438 0.375,0.219 10 false N58 4.115,1.281 4.469,1.521 0.354,0.24 10 false MM2 4.146,3.229 4.479,3.438 0.333,0.208 10 false NN2

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>UTILITY


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruptions in the wire harness and connector corresponding to a DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>CHECK FOR INTERMITTENT PROBLEMS

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Speed Open Rear speed sensor RH open detection Error or Normal Normal: Momentary interruption not detected
Normal: Momentary interruption not detected
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal".
RL Speed Open Rear speed sensor LH open detection Error or Normal Error: Momentary interruption detected
Normal: Momentary interruption not detected
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal".
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Speed Open
RL Speed Open
50003 105 202,203
OK:

Normal (There are no momentary interruptions.)


HINT:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (REAR SPEED SENSOR)

NG

5.CHECK REAR SPEED SENSOR INSTALLATION
2.READ VALUE USING GTS (REAR SPEED SENSOR)
a.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear speed sensor RH Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear speed sensor LH Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Wheel Speed
RL Wheel Speed
50003 105 3,4

b.

Check the speed value output from the speed sensor displayed on the GTS.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK


OK:

The speed value output from the speed sensor displayed on the GTS is similar to the speed indicated on the speedometer.



Result:
Proceed to
OK
NG



OK

3.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)

NG

5.CHECK REAR SPEED SENSOR INSTALLATION
3.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
a.

Turn the power switch off.


b.

Perform the sensor check in Test Mode Procedure.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>TEST MODE PROCEDURE

Chassis > ABS/VSC/TRC > Utility
Tester Display
Signal Check
50005 105 1003
OK:

All Test Mode DTCs are cleared.



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

5.CHECK REAR SPEED SENSOR INSTALLATION
4.RECONFIRM DTC
a.

Turn the power switch off.



c.

Turn the power switch on (READY).


d.

Perform a road test.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTCs C1466 and C1467 are not output. A
DTCs C1466 and/or C1467 are output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DTC CHECK / CLEAR




A

B

6.INSPECT PARKING BRAKE WIRE ASSEMBLY
5.CHECK REAR SPEED SENSOR INSTALLATION
a.
C210569C09
1,1.167 1.313,1.521 false 1.385,1.49 1.698,1.646 0.313,0.156 10 false *a 0.896,1.74 1.208,1.896 0.313,0.156 10 false *b 2.396,1.75 2.708,1.948 0.313,0.198 10 false *c
*a No clearance
*b OK
*c NG


Turn the power switch off.


b.

Check the speed sensor installation.

OK:

There is no clearance between the sensor and rear axle hub.



Result:
Proceed to
OK
NG



OK

6.INSPECT PARKING BRAKE WIRE ASSEMBLY

NG

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

6.INSPECT PARKING BRAKE WIRE ASSEMBLY
a.
C405858C01
0.823,0.427 1.125,0.677 0.302,0.25 0.823,0.75 1.125,1 0.302,0.25 2.323,0.406 2.688,0.656 0.365,0.25 2.333,0.708 2.677,0.958 0.344,0.25 0.469,2.479 0.844,1.906 true 1.458,2.521 1.083,1.896 true 0.094,0.104 0.406,0.302 0.313,0.198 10 false *1 0.844,0.479 1.156,0.677 0.313,0.198 10 false M50 0.854,0.792 1.167,0.99 0.313,0.198 10 false N58 1.219,0.479 1.531,0.677 0.313,0.198 10 false *A 1.219,0.792 1.531,0.99 0.313,0.198 10 false *B 2.365,0.458 2.75,0.635 0.385,0.177 10 false MM2 2.365,0.76 2.729,0.958 0.365,0.198 10 false NN2 2.75,0.771 3.063,0.969 0.313,0.198 10 false *B 2.76,0.458 3.073,0.656 0.313,0.198 10 false *A 0.302,2.5 0.625,2.719 0.323,0.219 10 false RA- 1.458,2.573 1.823,2.802 0.365,0.229 10 false RA+ 0.906,1.104 1.219,1.302 0.313,0.198 10 false *a 2.438,1.094 2.75,1.292 0.313,0.198 10 false *b 0.302,2.75 0.625,2.969 0.323,0.219 10 false LA- 1.458,2.792 1.823,3.021 0.365,0.229 10 false LA+ 1.771,2.594 2.083,2.792 0.313,0.198 10 false *A 0.604,2.521 0.917,2.719 0.313,0.198 10 false *A 0.594,2.771 0.906,2.969 0.313,0.198 10 false *B 1.75,2.823 2.063,3.021 0.313,0.198 10 false *B
*A for RH
*B for LH
*1 Skid Control Sensor Wire (Parking Brake Wire Assembly)
*a Front view of wire harness connector
(to Sensor Side Connector)
*b Front view of wire harness connector
(to Vehicle Side Connector)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Disconnect the M50 or N58 skid control sensor wire (parking brake wire assembly) connector.


c.

Disconnect the MM2 or NN2 skid control sensor wire (parking brake wire assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
M50-2 (RA+) - MM2-3 Always Below 1 Ω
M50-2 (RA+) or MM2-3 - Body ground and other terminals Always 10 kΩ or higher
M50-1 (RA-) - MM2-4 Always Below 1 Ω
M50-1 (RA-) or MM2-4 - Body ground and other terminals Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
N58-2 (LA+) - NN2-3 Always Below 1 Ω
N58-2 (LA+) or NN2-3 - Body ground and other terminals Always 10 kΩ or higher
N58-1 (LA-) - NN2-4 Always Below 1 Ω
N58-1 (LA-) or NN2-4 - Body ground and other terminals Always 10 kΩ or higher


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - REAR SPEED SENSOR)

NG

REPLACE PARKING BRAKE WIRE ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - REAR SPEED SENSOR)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Reconnect the MM2 or NN2 skid control sensor wire (parking brake wire assembly) connector.


c.

Disconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A42-22 (RR+) - M50-2 (RA+) Always Below 1 Ω
A42-22 (RR+) or M50-2 (RA+) - Body ground Always 10 kΩ or higher
A42-9 (RR-) - M50-1 (RA-) Always Below 1 Ω
A42-9 (RR-) or M50-1 (RA-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A42-20 (RL+) - N58-2 (LA+) Always Below 1 Ω
A42-20 (RL+) or N58-2 (LA+) - Body ground Always 10 kΩ or higher
A42-7 (RL-) - N58-1 (LA-) Always Below 1 Ω
A42-7 (RL-) or N58-1 (LA-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)
a.
C233859C92
0.646,0.521 1.135,0.813 0.49,0.292 2,0.521 2.49,0.813 0.49,0.292 0.969,1.344 1.177,1.781 true 2.323,1.344 2.531,1.781 true 1.188,1.813 1.583,2.052 0.396,0.24 10 false RA+ 2.552,1.823 2.979,2.031 0.427,0.208 10 false LA+ 0.135,0.083 0.323,0.24 0.188,0.156 10 false *a 0.76,0.594 1.052,0.75 0.292,0.156 10 false M50 2.125,0.594 2.573,0.792 0.448,0.198 10 false N58 0.427,0.583 0.74,0.781 0.313,0.198 10 false *A 1.771,0.573 2.083,0.771 0.313,0.198 10 false *B
*A for RH
*B for LH
*a Front view of wire harness connector
(to Rear Speed Sensor (Rear Axle Hub and Bearing Assembly))


Reconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Condition Specified Condition
M50-2 (RA+) - Body ground Power switch on (IG) 5.7 to 14 V

for LH
Tester Connection Condition Specified Condition
N58-2 (LA+) - Body ground Power switch on (IG) 5.7 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

NG