The TCM controls the shift solenoid valves SL1, SL2 and SLG to change the shift mode from gear mode to belt mode and vice versa.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P170300 | AT Solenoid Output Malfunction | Any of the following conditions are met for 1 second or more (2-trip detection logic):
·
The C1 clutch is engaged, C2 clutch is released and S1 synchronizer is engaged when 2 seconds or more have elapsed since the following conditions are met: -
The transmission revolution sensor (NOUT) signal indicates 1200 rpm or more -
TCM commands the C1 clutch to be released -
TCM commands the C2 clutch to be engaged ·
When the transmission revolution sensor (NOUT) signal indicates 2050 rpm or more, the C1 clutch is engaged, C2 clutch is released and S1 synchronizer is engaged. |
·
Continuously variable transaxle assembly ·
Wire harness or connector ·
TCM |
Comes on | DTC stored | SAE Code:
P1703 |
| Vehicle Condition | |||
|---|---|---|---|
| Pattern 1 | Pattern 2 | ||
| Diagnostic Condition | 2 seconds or more have elapsed since the following conditions are met:
·
The transmission revolution sensor (NOUT) signal is 1200 rpm or more ·
TCM commands the C1 clutch to be released ·
TCM commands the C2 clutch to be engaged |
○ | - |
| The transmission revolution sensor (NOUT) signal is 2050 rpm or more | - | ○ | |
| Malfunction Condition | C1 clutch is engaged, C2 clutch is released and S1 synchronizer is engaged | ○ | ○ |
| Duration | 1 second or more | 1 second or more | |
| Detection Logic | 2-trip detection logic | 2-trip detection logic | |
This DTC is stored when any of the above detection patterns is met.
The TCM monitors the changes in the shift state from belt mode to gear mode for abnormalities.
If the vehicle is being driven in gear mode when in the belt mode vehicle speed range, the TCM detects a malfunction, illuminates the MIL and stores a DTC.
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on.
Start the engine.
Perform the D Position Test inspection in Road Test.
Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>ROAD TEST
Stop the vehicle.
Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
Input the DTC: P170300.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Refer to DTC P074512, P077512 and P08C312.
for DTC P074512: Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>P074512
for DTC P077512: Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>P077512
for DTC P08C312: Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>P08C312
Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.
Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Trouble Codes.
Read the DTCs using the GTS.
If any DTCs other than P170300 are output, perform troubleshooting for those DTCs first.
| Result | Proceed to |
|---|---|
| Only DTC P170300 is output | A |
| DTC P170300 and other DTCs are output | B |
A
B
| *a | Component without harness connected
(Transmission Wire) |
Disconnect the C34 transmission wire connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (SL1+) - 7 (SL1-) | 20°C (68°F) | 5.0 to 5.6 Ω |
| 3 (SL2+) - 8 (SL2-) | 20°C (68°F) | 5.0 to 5.6 Ω |
| 1 (SLG+) - 6 (SLG-) | 20°C (68°F) | 5.0 to 5.6 Ω |
| 2 (SL1+) or 7 (SL1-) - Body ground and other terminals | Always | 10 kΩ or higher |
| 3 (SL2+) or 8 (SL2-) - Body ground and other terminals | Always | 10 kΩ or higher |
| 1 (SLG+) or 6 (SLG-) - Body ground and other terminals | Always | 10 kΩ or higher |
Connect the C34 transmission wire connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C33 TCM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C33-38 (SL1+) - C33-37 (SL1-) | 20°C (68°F) | 5.0 to 5.6 Ω |
| C33-19 (SL2+) - C33-20 (SL2-) | 20°C (68°F) | 5.0 to 5.6 Ω |
| C33-21 (SLG+) - C33-22 (SLG-) | 20°C (68°F) | 5.0 to 5.6 Ω |
| C33-38 (SL1+) or C33-37 (SL1-) - Body ground and other terminals | Always | 10 kΩ or higher |
| C33-19 (SL2+) or C33-20 (SL2-) - Body ground and other terminals | Always | 10 kΩ or higher |
| C33-21 (SLG+) or C33-22 (SLG-) - Body ground and other terminals | Always | 10 kΩ or higher |
Connect the C33 TCM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the TCM.
| Proceed to |
|---|
| NEXT |
NEXT
for Registration: Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Disconnect the transmission wire connector from the shift solenoid valves SL1, SL2 and SLG.
Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>VALVE BODY ASSEMBLY>REMOVAL
| *1 | Transmission Valve Body Assembly | *2 | Shift Solenoid Valve SLG |
| *3 | Shift Solenoid Valve SL1 | *4 | Shift Solenoid Valve SL2 |
| *a | Component without harness connected
(Shift Solenoid Valve SL1, SL1 and SLG) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Shift solenoid valve SL1 connector terminal 1 - terminal 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
| Shift solenoid valve SL2 connector terminal 1 - terminal 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
| Shift solenoid valve SLG connector terminal 1 - terminal 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the continuously variable transaxle assembly.
Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
for Registration: Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION