CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
| *A | except LHD, Manual Transaxle | *B | for LHD, Manual Transaxle |
| *1 | Main Body ECU (Multiplex Network Body ECU) | - | - |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
for LHD:Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Reconnect the instrument panel junction block assembly connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Input/Output | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|---|
| A-11 (GND1) - Body ground | - | - | Ground | Always | Below 1 Ω | - |
| A-30 (ACC) - Body ground | - | Input | ACC power supply | Engine switch on (ACC) | 11 to 14 V | ACC SW |
| Engine switch off | Below 1 V | |||||
| A-31 (BECU) - Body ground | - | Input | Battery power supply | Always | 11 to 14 V | - |
| A-32 (IG) - Body ground | - | Input | IG power supply | Engine switch on (IG) | 11 to 14 V*1
10.5 to 16 V*2 |
IG SW |
| Engine switch off | Below 1 V |
*1: except Manual Transaxle, with Stop and Start System
*2: for Manual Transaxle, with Stop and Start System
Install the main body ECU (multiplex network body ECU) to the instrument panel junction block assembly.
for LHD:Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>INSTALLATION
for RHD:Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>INSTALLATION
Measure the voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Wiring Color | Input/Output | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|---|
| 4F-29 (BZR) - Body ground | L - Body ground | Output | Wireless door lock buzzer output | Active Test Wireless Buzzer on | Pulse generation
(frequency: 2 kHz, high voltage: 11 to 14 V, low voltage: below 1 V) |
- |
| Active Test Wireless Buzzer off | Below 1 V |
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
Disconnect the G54 certification ECU (smart key ECU assembly) connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Input/Output | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|---|
| G54-18 (E) - Body ground | W-B - Body ground | - | Ground | Always | Below 1 Ω | - |
| G54-4 (+B) - Body ground | P - Body ground | Input | Power supply | Always | 11 to 14 V | - |
| G54-15 (CUTB) - Body ground | V - Body ground | Input | Dark current cut pin* | Always | 11 to 14 V | - |
*: In order to prevent the vehicle battery from being depleted when the vehicle is shipped long distances, a fuse that cuts unnecessary electrical load while the vehicle is being shipped is installed in the circuit. If the fuse is removed, the circuit becomes open. If the fuse that is between the vehicle battery and terminal CUTB is removed and the circuit is open, the certification ECU (smart key ECU assembly) changes to a certain control mode (example: the transmission of radio waves every 0.25 seconds, which form the detection area, stops).
Reconnect the G54 certification ECU (smart key ECU assembly) connector.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Wiring Color | Input/Output | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|---|
| G54-17 (IG1D) - G54-18 (E) | L - W-B | Output | IG power supply | Engine switch off → on (IG) | 1 V or less → 9 V or higher | Power Source Control
IG Relay Monitor (Outside) |
| G54-16 (ACCD) - G54-18 (E) | G - W-B | Output | ACC power supply | Engine switch off → on (ACC) | 1 V or less → 8.5 V or higher | Power Source Control
ACC Relay Monitor |
| M7-18 (RCO) - G54-18 (E) | L - W-B | Output | Output to door control receiver
(Power supply for door control receiver. Certification ECU (smart key ECU assembly) outputs 5 V when receiver starts operating.) |
Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area 3.
Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed |
Pulse generation
(See waveform 1) |
- |
| M7-19 (RDAM) - G54-18 (E) | G - W-B | Input | Door control receiver verifies data received from electrical key transmitter sub-assembly.
Door control receiver sends data from electrical key transmitter sub-assembly to certification ECU (smart key ECU assembly) (Door control receiver intermittently grounds 12 V signal from certification ECU (smart key ECU assembly)). |
Proceed:
1.
Engine switch off 2.
All doors locked 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area 5.
Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed |
Pulse generation
(See waveform 2) |
- |
| M7-20 (CSEL) - G54-18 (E) | BE - W-B | Output | Communication channel switching circuit | Procedure:
1.
Engine switch off 2.
All doors closed |
Below 1 V → pulse generation | - |
| *a | Before lock or unlock switch of electrical key transmitter sub-assembly pressed |
| *b | After lock or unlock switch of electrical key transmitter sub-assembly pressed |
Using an oscilloscope, check waveform 1.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | M7-18 (RCO) - G54-18 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area 3.
Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed |
| *a | Before lock or unlock switch of electrical key transmitter sub-assembly pressed |
| *b | After lock or unlock switch of electrical key transmitter sub-assembly pressed |
Using an oscilloscope, check waveform 2.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | M7-19 (RDAM) - G54-18 (E) |
| Tool Setting | 5 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Engine switch off 2.
All doors locked 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area 5.
Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed |