The multiplex network door ECU receives signals from the latch switch, initial switch, pawl switch and back door courtesy switch, which are built into the back door lock assembly. Based on these switch signals, the latch position of the back door lock with courtesy light switch assembly is determined.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2251 | Back Door Closer Switch Malfunction | While the back door closer is operating, a malfunction is detected in position information from the back door courtesy switch within a specified amount of time. | ·
Back door lock with courtesy light switch assembly ·
Harness or connector ·
Multiplex network door ECU ·
Instrument panel junction block assembly ·
Main body ECU (multiplex network body ECU) |
If the replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU has been performed, initialize the power back door system.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>INITIALIZATION
If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.
As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*
*: w/ Door Control Battery
Read the Data List according to the display on the GTS.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Courtesy SW | Back door courtesy switch signal | ON or OFF | ON: Back door open
OFF: Back door closed |
- |
| Tester Display |
|---|
| Courtesy SW |
The display is as specified in the normal condition column.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the back door lock with courtesy light switch assembly.
Inspect the back door lock with courtesy light switch assembly.
Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 4H*1 or 4N*2 instrument panel junction block assembly connector.
*1: for LHD, Manual Transaxle
*2: except LHD, Manual Transaxle
Disconnect the R14 back door lock with courtesy light switch assembly connector.
Disconnect the R18 multiplex network door ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R14-4 (CTY) - R18-11 (FUL) | Always | Below 1 Ω |
| R14-1 (E) - Body ground | Always | Below 1 Ω |
| R14-4 (CTY) or R18-11 (FUL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 4H*1 or 4N*2 instrument panel junction block assembly connector.
*1: for LHD, Manual Transaxle
*2: except LHD, Manual Transaxle
Disconnect the R18 multiplex network door ECU connector.
Disconnect the R14 back door lock with courtesy light switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4H-34 or R18-11 (FUL) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4N-34 or R18-11 (FUL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-4 (BCTY) - 4H-34 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-4 (BCTY) - 4N-34 | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
Disconnect the R18 multiplex network door ECU connector.
Read the Data List according to the display on the GTS.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Back Door Courtesy SW | Back door courtesy switch signal | ON or OFF | ON: Back door open
OFF: Back door closed |
- |
| Tester Display |
|---|
| Back Door Courtesy SW |
The display is as specified in the normal condition column.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C