The back door lock with courtesy light switch assembly is controlled by the multiplex network door ECU. The multiplex network door ECU is activated according to the switch signals in the back door lock with courtesy light switch assembly.
Inspect fuses for circuits related to this system before performing the following inspection procedure.
If the replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU has been performed, initialize the power back door system.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>INITIALIZATION
If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.
As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*
*: w/ Door Control Battery
Check for DTCs.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC B2250 is output | B |
| DTC B2251 is output | C |
A
B
C
Check if the back door can be fully closed by hand.
| Result | Proceed to |
|---|---|
| The back door can be closed normally | A |
| The back door cannot be closed normally | B |
A
B
| *a | Rear view of wire harness connector
(to Multiplex Network Door ECU) |
Disconnect the multiplex network door ECU connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R19-10 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R18-20 (ECUB) - Body ground | Always | 11 to 14 V |
| R19-1 (B) - Body ground | Always | 11 to 14 V |
| R18-18 (IG) - Body ground | Engine switch on (IG) | 11 to 14 V |
| Engine switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the back door lock with courtesy light switch assembly.
Inspect the back door lock with courtesy light switch assembly.
Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the R13 and R14 back door lock with courtesy light switch assembly connectors.
Disconnect the R18 and R19 multiplex network door ECU connectors.
Disconnect the 4H*1 or 4N*2 instrument panel junction block assembly connector.
*1: for LHD, Manual Transaxle
*2: except LHD, Manual Transaxle
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R13-2 (M+) - R19-4 (DC+) | Always | Below 1 Ω |
| R13-1 (M-) - R19-3 (DC-) | Always | Below 1 Ω |
| R14-4 (CTY) - R18-11 (FUL) | Always | Below 1 Ω |
| R14-2 (FSW) - R18-13 (PAWL) | Always | Below 1 Ω |
| R14-3 (CLS) - R18-9 (HAF) | Always | Below 1 Ω |
| R14-6 (OPN) - R18-7 (POS) | Always | Below 1 Ω |
| R14-1 (E) - Body ground | Always | Below 1 Ω |
| R13-2 (M+) or R19-4 (DC+) - Body ground | Always | 10 kΩ or higher |
| R13-1 (M-) or R19-3 (DC-) - Body ground | Always | 10 kΩ or higher |
| R14-2 (FSW) or R18-13 (PAWL) - Body ground | Always | 10 kΩ or higher |
| R14-4 (CTY) or R18-11 (FUL) - Body ground | Always | 10 kΩ or higher |
| R14-3 (CLS) or R18-9 (HAF) - Body ground | Always | 10 kΩ or higher |
| R14-6 (OPN) or R18-7 (POS) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG