When the power back door warning system does not operate, one of the following may be malfunctioning: 1) wireless door lock control system, 2) power back door warning buzzer circuit or 3) multiplex network door ECU.
If the replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU has been performed, initialize the power back door system.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>INITIALIZATION
The power back door warning function can be customized. Make sure the function is ON.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>CUSTOMIZE PARAMETERS
If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.
As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*
*: w/ Door Control Battery
Check power back door system operation.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>OPERATION CHECK
| Result | Proceed to |
|---|---|
| Hazard warning light does not come on (w/ Power Back Door Hazard Warning Light) | A |
| Power back door warning buzzer does not operate | B |
A
B
Check wireless door lock operation.
Hazard answer-back function operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the multiplex network door ECU with a new or normally functioning one.
Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR CLOSER ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Perform the initialization for the multiplex network door ECU.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Check that the power back door hazard warning lights operate normally.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>OPERATION CHECK
The power back door hazard warning lights operate normally.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
Perform the Active Test according to the display on the GTS.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| PBD Buzzer | Power back door warning buzzer sound | ON or OFF | - |
| Tester Display |
|---|
| PBD Buzzer |
Power back door warning buzzer sounds.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the Q2 power back door warning buzzer connector.
Disconnect the R18 multiplex network door ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q2-1 (BZR+) - R18-16 (BZR+) | Always | Below 1 Ω |
| Q2-2 (BZR-) - Body ground | Always | Below 1 Ω |
| Q2-1 (BZR+) or R18-16 (BZR+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the power back door warning buzzer with a new or normally functioning one.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR WARNING BUZZER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check that the power back door warning buzzer operates normally.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>OPERATION CHECK
Power back door warning buzzer sounds.
| Proceed to |
|---|
| OK |
| NG |
OK
NG