When the jam protection function activates during power back door operation, one of the following may be the cause: 1) improper fit of back door, or a foreign object is stuck in the back door, 2) malfunctioning power back door sensor assembly circuit or 3) malfunctioning multiplex network door ECU.
If the replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU has been performed, initialize the power back door system.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>INITIALIZATION
Check if there are any foreign objects interfering with back door operation.
| Result | Proceed to |
|---|---|
| There are no foreign objects | A |
| There are foreign objects | B |
A
B
Check back door operation.
Turn the main switch so that it is not pushed.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>CUSTOMIZE PARAMETERS
This check is possible only when the "System Settings" customization setting using the multi-information display in the combination meter assembly is set to "Off" (The default setting is "On").
Open/close the back door by hand.
| Result | Proceed to |
|---|---|
| The back door fully opens and closes smoothly | A |
| The back door does not fully open and close smoothly | B |
Check main switch condition.
The "System Settings" customization setting using the multi-information display in the combination meter assembly is set to "On" (The default setting is "On").
Turn the main switch so that it is pushed.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>CUSTOMIZE PARAMETERS
A
B
Check the Data List to determine if the power back door sensor assembly functions properly.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| PBD Touch Sensor (Right) | Power back door sensor assembly RH signal | ON, OFF or Open | ON: Power back door sensor assembly RH pressed
OFF: Power back door sensor assembly RH not pressed Open: Power back door sensor assembly RH circuit open |
- |
| PBD Touch Sensor (Left) | Power back door sensor assembly LH signal | ON, OFF or Open | ON: Power back door sensor assembly LH pressed
OFF: Power back door sensor assembly LH not pressed Open: Power back door sensor assembly LH circuit open |
- |
| Tester Display |
|---|
| PBD Touch Sensor (Right) |
| PBD Touch Sensor (Left) |
| Result | Proceed to |
|---|---|
| On the GTS screen, ON or OFF is displayed accordingly | A |
| On the GTS screen, ON or OFF is not displayed accordingly or Open is displayed for power back door sensor assembly RH | B |
| On the GTS screen, ON or OFF is not displayed accordingly or Open is displayed for power back door sensor assembly LH | C |
A
B
C
Temporarily replace the power back door unit assembly set with a new or normally functioning one.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR DRIVE UNIT>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check power back door system operation.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>OPERATION CHECK
Power back door system operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the power back door sensor assembly RH.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR TOUCH SENSOR>REMOVAL
Inspect the power back door sensor assembly RH.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR TOUCH SENSOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the R8 power back door sensor assembly RH connector.
Disconnect the R18 multiplex network door ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R8-1 (OSR) - R18-6 (OSR) | Always | Below 1 Ω |
| R8-2 (OSRE) - R18-24 (OSE) | Always | Below 1 Ω |
| R8-1 (OSR) or R18-6 (OSR) - Body ground | Always | 10 kΩ or higher |
| R8-2 (OSRE) or R18-24 (OSE) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the power back door sensor assembly LH.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR TOUCH SENSOR>REMOVAL
Inspect the power back door sensor assembly LH.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR TOUCH SENSOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the R9 power back door sensor assembly LH connector.
Disconnect the R18 multiplex network door ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R9-1 (OSL) - R18-26 (OSL) | Always | Below 1 Ω |
| R9-2 (OSLE) - R18-24 (OSE) | Always | Below 1 Ω |
| R9-1 (OSL) or R18-26 (OSL) - Body ground | Always | 10 kΩ or higher |
| R9-2 (OSLE) or R18-24 (OSE) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG