Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (for HV Model with Memory)
RM3620E _58 Vehicle Interior _076405 SEAT _0374972 FRONT POWER SEAT CONTROL SYSTEM(for HV Model with Memory) U

SEAT  FRONT POWER SEAT CONTROL SYSTEM(for HV Model with Memory)  TERMINALS OF ECU  


CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)


E360013C05
5.365,0.333 5.781,0.583 0.417,0.25 2.365,0.333 2.781,0.583 0.417,0.25 1.5,0.333 1.917,0.583 0.417,0.25 0.792,0.333 1.208,0.583 0.417,0.25 3.021,0.333 3.438,0.583 0.417,0.25 4.552,0.333 4.969,0.583 0.417,0.25 5.49,0.385 5.802,0.583 0.313,0.198 10 false S8 3.146,0.385 3.458,0.583 0.313,0.198 10 false S6 1.625,0.385 1.938,0.583 0.313,0.198 10 false S7 0.927,0.385 1.385,0.583 0.458,0.198 10 false T7 1.25,0.333 1.563,0.531 0.313,0.198 10 false *A 1.958,0.344 2.271,0.542 0.313,0.198 10 false *B 3.479,0.344 3.792,0.542 0.313,0.198 10 false *B 2.813,0.344 3.125,0.542 0.313,0.198 10 false *A 2.5,0.385 2.958,0.583 0.458,0.198 10 false T6 5.01,0.354 5.323,0.552 0.313,0.198 10 false *A 5.833,0.354 6.146,0.552 0.313,0.198 10 false *B 4.677,0.385 5.135,0.583 0.458,0.198 10 false T8
*A for LHD *B for RHD


a.

for LHD

i.

Disconnect the T7 and T8 position control ECU assembly (driver seat) connectors.


ii.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
T7-2 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
T7-3 (+B) - Body ground W - Body ground Battery power supply Power switch off 11 to 14 V
T8-1 (IG) - Body ground P - Body ground Ignition power supply Power switch off Below 1 V
Power switch on (IG) 11 to 14 V
T8-15 (SYSB) - Body ground G - Body ground System power source Power switch off 11 to 14 V


iii.

Reconnect the T7 and T8 position control ECU assembly (driver seat) connectors.


iv.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
T7-1 (SLD+) - Body ground L - Body ground Slide motor signal (forward) Slide switch off Below 1 V
Slide switch on (Forward) 11 to 14 V
T7-5 (SLD-) - Body ground GR - Body ground Slide motor signal (rearward) Slide switch off Below 1 V
Slide switch on (Rearward) 11 to 14 V
T7-6 (LFT+) - Body ground V - Body ground Rear lifter motor signal (upward) Rear lifter switch off Below 1 V
Rear lifter switch on (Upward) 11 to 14 V
T7-7 (FRV+) - Body ground B - Body ground Front vertical motor signal (upward) Front vertical switch off Below 1 V
Front vertical switch on (Upward) 11 to 14 V
T7-9 (L+) - Body ground V - Body ground Lumbar support adjuster motor signal (forward) Lumbar support adjuster switch off Below 1 V
Lumbar support adjuster switch on (Forward) 11 to 14 V
T7-10 (RCL+) - Body ground P - Body ground Reclining motor signal (forward) Reclining switch off Below 1 V
Reclining switch on (Forward) 11 to 14 V
T6-3 (L-) - Body ground L - Body ground Lumbar support adjuster motor signal (rearward) Lumbar support adjuster switch off Below 1 V
Lumbar support adjuster switch on (Rearward) 11 to 14 V
T6-4 (FRV-) - Body ground R - Body ground Front vertical motor signal (downward) Front vertical switch off Below 1 V
Front vertical switch on (Downward) 11 to 14 V
T6-5 (LFT-) - Body ground G - Body ground Lifter motor signal (downward) Rear lifter switch off Below 1 V
Rear lifter switch on (Downward) 11 to 14 V
T6-6 (RCL-) - Body ground LG - Body ground Reclining motor signal (rearward) Reclining switch off Below 1 V
Reclining switch on (Rearward) 11 to 14 V
T8-4 (LFLF) - Body ground W - Body ground Lumbar support adjuster switch (forward) signal Lumbar support adjuster switch off 11 to 14 V
Lumbar support adjuster switch on (Forward) Below 1 V
T8-6 (FRVU) - Body ground L - Body ground Front vertical switch (upward) signal Front vertical switch off 11 to 14 V
Front vertical switch on (Upward) Below 1 V
T8-7 (LFTU) - Body ground BR - Body ground Rear lifter switch (upward) signal Rear lifter switch off 11 to 14 V
Rear lifter switch on (Upward) Below 1 V
T8-8 (RCLF) - Body ground R - Body ground Reclining switch (forward) signal Reclining switch off 11 to 14 V
Reclining switch on (Forward) Below 1 V
T8-9 (SLDF) - Body ground B - Body ground Slide switch (forward) signal Slide switch off 11 to 14 V
Slide switch on (Forward) Below 1 V
T8-12 (SGND) - Body ground BR - Body ground Sensor ground Always Below 1 Ω
T8-18 (LFLR) - Body ground L - Body ground Lumbar support adjuster switch (rearward) signal Lumbar support adjuster switch off 11 to 14 V
Lumbar support adjuster switch on (Rearward) Below 1 Ω
T8-20 (FRVD) - Body ground V - Body ground Front vertical switch (downward) signal Front vertical switch off 11 to 14 V
Front vertical switch on (Downward) Below 1 V
T8-21 (LFTD) - Body ground LG - Body ground Rear lifter switch (downward) signal Rear lifter switch off 11 to 14 V
Rear lifter switch on (Downward) Below 1 V
T8-22 (RCLR) - Body ground G - Body ground Reclining switch (rearward) signal Reclining switch off 11 to 14 V
Reclining switch on (Rearward) Below 1 V
T8-23 (SLDR) - Body ground GR - Body ground Slide switch (rearward) signal Slide switch off 11 to 14 V
Slide switch on (Rearward) Below 1 V


v.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
T8-10 (SSFV) - Body ground L - Body ground Front vertical position signal Front vertical function operating Pulse generation
T8-11 (SSRR) - Body ground V - Body ground Reclining position signal Reclining function operating Pulse generation
T8-25 (SSRL) - Body ground B - Body ground Rear lifter position signal Rear lifter function operating Pulse generation
T8-26 (SSRS) - Body ground G - Body ground Slide position signal Slide function operating Pulse generation



b.

for RHD

i.

Disconnect the S7 and S8 position control ECU assembly (driver seat) connectors.


ii.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
S7-2 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
S7-3 (+B) - Body ground W - Body ground Battery power supply Power switch off 11 to 14 V
S8-1 (IG) - Body ground P - Body ground Ignition power supply Power switch off Below 1 V
Power switch on (IG) 11 to 14 V
S8-15 (SYSB) - Body ground G - Body ground System power source Power switch off 11 to 14 V


iii.

Reconnect the S7 and S8 position control ECU assembly (driver seat) connectors.


iv.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
S7-1 (SLD+) - Body ground L - Body ground Slide motor signal (forward) Slide switch off Below 1 V
Slide switch on (Forward) 11 to 14 V
S7-5 (SLD-) - Body ground GR - Body ground Slide motor signal (rearward) Slide switch off Below 1 V
Slide switch on (Rearward) 11 to 14 V
S7-6 (LFT+) - Body ground V - Body ground Rear lifter motor signal (upward) Rear lifter switch off Below 1 V
Rear lifter switch on (Upward) 11 to 14 V
S7-7 (FRV+) - Body ground B - Body ground Front vertical motor signal (upward) Front vertical switch off Below 1 V
Front vertical switch on (Upward) 11 to 14 V
S7-9 (L+) - Body ground V - Body ground Lumbar support adjuster motor signal (forward) Lumbar support adjuster switch off Below 1 V
Lumbar support adjuster switch on (Forward) 11 to 14 V
S7-10 (RCL+) - Body ground P - Body ground Reclining motor signal (forward) Reclining switch off Below 1 V
Reclining switch on (Forward) 11 to 14 V
S6-3 (L-) - Body ground L - Body ground Lumbar support adjuster motor signal (rearward) Lumbar support adjuster switch off Below 1 V
Lumbar support adjuster switch on (Rearward) 11 to 14 V
S6-4 (FRV-) - Body ground R - Body ground Front vertical motor signal (downward) Front vertical switch off Below 1 V
Front vertical switch on (Downward) 11 to 14 V
S6-5 (LFT-) - Body ground G - Body ground Lifter motor signal (downward) Rear lifter switch off Below 1 V
Rear lifter switch on (Downward) 11 to 14 V
S6-6 (RCL-) - Body ground LG - Body ground Reclining motor signal (rearward) Reclining switch off Below 1 V
Reclining switch on (Rearward) 11 to 14 V
S8-4 (LFLF) - Body ground W - Body ground Lumbar support adjuster switch (forward) signal Lumbar support adjuster switch off 11 to 14 V
Lumbar support adjuster switch on (Forward) Below 1 V
S8-6 (FRVU) - Body ground L - Body ground Front vertical switch (upward) signal Front vertical switch off 11 to 14 V
Front vertical switch on (Upward) Below 1 V
S8-7 (LFTU) - Body ground BR - Body ground Rear lifter switch (upward) signal Rear lifter switch off 11 to 14 V
Rear lifter switch on (Upward) Below 1 V
S8-8 (RCLF) - Body ground R - Body ground Reclining switch (forward) signal Reclining switch off 11 to 14 V
Reclining switch on (Forward) Below 1 V
S8-9 (SLDF) - Body ground B - Body ground Slide switch (forward) signal Slide switch off 11 to 14 V
Slide switch on (Forward) Below 1 V
S8-12 (SGND) - Body ground BR - Body ground Sensor ground Always Below 1 Ω
S8-18 (LFLR) - Body ground L - Body ground Lumbar support adjuster switch (rearward) signal Lumbar support adjuster switch off 11 to 14 V
Lumbar support adjuster switch on (Rearward) Below 1 Ω
S8-20 (FRVD) - Body ground V - Body ground Front vertical switch (downward) signal Front vertical switch off 11 to 14 V
Front vertical switch on (Downward) Below 1 V
S8-21 (LFTD) - Body ground LG - Body ground Rear lifter switch (downward) signal Rear lifter switch off 11 to 14 V
Rear lifter switch on (Downward) Below 1 V
S8-22 (RCLR) - Body ground G - Body ground Reclining switch (rearward) signal Reclining switch off 11 to 14 V
Reclining switch on (Rearward) Below 1 V
S8-23 (SLDR) - Body ground GR - Body ground Slide switch (rearward) signal Slide switch off 11 to 14 V
Slide switch on (Rearward) Below 1 V


v.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
S8-10 (SSFV) - Body ground L - Body ground Front vertical position signal Front vertical function operating Pulse generation
S8-11 (SSRR) - Body ground V - Body ground Reclining position signal Reclining function operating Pulse generation
S8-25 (SSRL) - Body ground B - Body ground Rear lifter position signal Rear lifter function operating Pulse generation
S8-26 (SSRS) - Body ground G - Body ground Slide position signal Slide function operating Pulse generation




CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


B472410C60
1.125,3.25 1.563,3.5 0.438,0.25 3.156,3.219 3.594,3.469 0.438,0.25 5.448,3.208 5.885,3.458 0.438,0.25 1.698,4.573 2.135,4.823 0.438,0.25 1.104,6.167 1.542,6.417 0.438,0.25 3.667,6.125 4.104,6.375 0.438,0.25 5.302,6.208 5.74,6.458 0.438,0.25 6.313,6.198 6.75,6.448 0.438,0.25 3.365,7.646 3.802,7.896 0.438,0.25 5.385,4.615 5.823,4.865 0.438,0.25 1.656,1.208 1.958,1.208 true 1.667,1.552 1.969,1.552 true 1.667,1.875 1.969,1.875 true 1.625,0.667 1.833,0.313 1.833,0.313 1.979,0.313 true 3.531,7.688 3.688,7.865 0.156,0.177 10 false A 3.74,0.969 3.896,1.135 0.156,0.167 10 false A 2.042,1.135 2.354,1.333 0.313,0.198 10 false G43 2.052,1.479 2.365,1.677 0.313,0.198 10 false G44 2.052,1.802 2.365,2 0.313,0.198 10 false G45 0.875,1.073 1.188,1.271 0.313,0.198 10 false 4H 0.875,1.656 1.188,1.854 0.313,0.198 10 false 4F 0.875,2.021 1.188,2.219 0.313,0.198 10 false 4L 5.854,1.146 6.167,1.344 0.313,0.198 10 false 4D 5.854,1.76 6.167,1.958 0.313,0.198 10 false 4A 1.208,3.292 1.521,3.49 0.313,0.198 10 false G45 3.25,3.26 3.563,3.458 0.313,0.198 10 false G44 5.542,3.26 5.854,3.458 0.313,0.198 10 false G43 1.833,4.615 2.146,4.813 0.313,0.198 10 false 4A 1.25,6.219 1.563,6.417 0.313,0.198 10 false 4F 3.802,6.177 4.115,6.375 0.313,0.198 10 false 4H 5.427,6.24 5.74,6.438 0.313,0.198 10 false 4K 6.448,6.24 6.76,6.438 0.313,0.198 10 false 4L 5.521,4.667 5.833,4.865 0.313,0.198 10 false 4D 0.896,2.25 1.156,2.417 0.26,0.167 10 false 4K 2.021,0.24 2.24,0.385 0.219,0.146 10 false *1
*1 Main Body ECU (Multiplex Network Body ECU) - -


a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL

for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL


b.

Connect the instrument panel junction block assembly connectors.


c.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A-32 (IG) - Body ground None - Body ground Ignition power supply Power switch on (IG) 11 to 14 V
Power switch off Below 1 V
A-31 (BECU) - Body ground None - Body ground Battery power supply Power switch off 11 to 14 V
A-30 (ACC) - Body ground None - Body ground ACC power supply Power switch on (ACC) 11 to 14 V
Power switch off Below 1 V
A-11 (GND1) - Body ground None - Body ground Ground Always Below 1 Ω



e.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G44-1 (FLCY) - Body ground*1 R - Body ground Front door courtesy light switch assembly (driver door) input Front door (driver door) open Below 1 V
Front door (driver door) closed 4.7 to 5.3 V
G44-6 (FRCY) - Body ground*2 BE - Body ground Front door courtesy light switch assembly (driver door) input Front door (driver door) open Below 1 V
Front door (driver door) closed 4.7 to 5.3 V
G43-7 (MM) - Body ground L - Body ground SET switch signal for seat memory switch (driver door) SET switch on Below 1 V
SET switch off 11 to 14 V
G43-9 (M2) - Body ground R - Body ground*1
BR - Body ground*2
M2 switch signal for seat memory switch (driver door) M2 switch on Below 1 V
M2 switch off 11 to 14 V
G43-10 (M1) - Body ground GR - Body ground M1 switch signal for seat memory switch (driver door) M1 switch on Below 1 V
M1 switch off 11 to 14 V

*1: for LHD

*2: for RHD