Signals are input into the position control ECU assembly driver seat. The built-in ECU manages the signals received from the position control ECU assembly (driver seat) and operates each motor. If the position control ECU assembly (driver seat) receives 2 or more operation signals for the same motor, the motor will be stopped. Manual operation resumes when the position control ECU assembly (driver seat) receives only 1 signal.
Initializing the position control ECU assembly (driver seat) will clear the seat position memory.
Make sure to initialize the position control ECU assembly (driver seat) after replacing the seat assembly or any related parts (including removal and installation).
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for HV Model with Memory)>REGISTRATION
Check that each function of the power seat operates normally by using the front power seat switch (driver seat).
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for HV Model with Memory)>OPERATION CHECK
| Result | Proceed to |
|---|---|
| One or more power seat functions do not operate | A |
| All power seat functions do not operate | B |
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Driver Seat / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Reclining Rear | Reclining switch signal (Rearward) | ON or OFF | ON: Reclining switch (Rearward) on
OFF: Reclining switch (Rearward) off |
- |
| Reclining Front | Reclining switch signal (Forward) | ON or OFF | ON: Reclining switch (Forward) on
OFF: Reclining switch (Forward) off |
- |
| Front Vertical Down | Front vertical switch signal (Downward) | ON or OFF | ON: Front vertical switch (Downward) on
OFF: Front vertical switch (Downward) off |
- |
| Front Vertical Up | Front vertical switch signal (Upward) | ON or OFF | ON: Front vertical switch (Upward) on
OFF: Front vertical switch (Upward) off |
- |
| Lifter Switch Down | Rear lifter switch signal (Downward) | ON or OFF | ON: Rear lifter switch (Downward) on
OFF: Rear lifter switch (Downward) off |
- |
| Lifter Switch Up | Rear lifter switch signal (Upward) | ON or OFF | ON: Rear lifter switch (Upward) on
OFF: Rear lifter switch (Upward) off |
- |
| Slide Rear | Slide switch signal (Rearward) | ON or OFF | ON: Slide switch (Rearward) on
OFF: Slide switch (Rearward) off |
- |
| Slide Front | Slide switch signal (Forward) | ON or OFF | ON: Slide switch (Forward) on
OFF: Slide switch (Forward) off |
- |
| Lumbar Switch Front | Lumbar support adjuster switch signal (Forward) | ON or OFF | ON: Lumbar support adjuster switch (Forward) on
OFF: Lumbar support adjuster switch (Forward) off |
- |
| Lumbar Switch Rear | Lumbar support adjuster switch signal (Rearward) | ON or OFF | ON: Lumbar support adjuster switch (Rearward) on
OFF: Lumbar support adjuster switch (Rearward) off |
- |
| Tester Display |
|---|
| Reclining Rear |
| Reclining Front |
| Front Vertical Down |
| Front Vertical Up |
| Lifter Switch Down |
| Lifter Switch Up |
| Slide Rear |
| Slide Front |
| Lumbar Switch Front |
| Lumbar Switch Rear |
On the GTS screen, ON or OFF is displayed accordingly
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Enter the following menus: Body Electrical / Driver Seat / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Seat Reclining | Seat reclining operation | OFF/Rear/Front | - |
| Front Vertical Operation | Seat front vertical operation | OFF/Down/Up | - |
| Lifter Operation | Seat lifter operation | OFF/Down/Up | - |
| Seat Slide Operation | Seat slide operation | OFF/Rear/Front | - |
| Lumbar Slide | Lumbar support operation | OFF/Rear/Front | - |
| Tester Display |
|---|
| Seat Reclining |
| Tester Display |
|---|
| Front Vertical Operation |
| Tester Display |
|---|
| Lifter Operation |
| Tester Display |
|---|
| Seat Slide Operation |
| Tester Display |
|---|
| Lumbar Slide |
| Result | Proceed to |
|---|---|
| Slide function does not operate normally | A |
| Front vertical function does not operate normally | B |
| Lifter function does not operate normally | C |
| Reclining function does not operate normally | D |
| Lumbar support adjustment function does not operate normally | E |
A
B
C
D
E
Remove the slide motor (front seat adjuster assembly [driver seat]).
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY
Inspect the slide motor (front seat adjuster assembly [driver seat]).
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the T7*1 or S7*2 position control ECU assembly (driver seat) connector.
Disconnect the T1*1 or S1*2 slide motor (front seat adjuster assembly [driver seat]) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
Check the wire harness and connector between the position control ECU assembly (driver seat) and applicable motor.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T7-1 (SLD+) - T1-4 | Always | Below 1 Ω |
| T7-1 (SLD+) or T1-4 - Other terminals and body ground | Always | 10 kΩ or higher |
| T7-5 (SLD-) - T1-1 | Always | Below 1 Ω |
| T7-5 (SLD-) or T1-1 - Other terminals and body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S7-1 (SLD+) - S1-4 | Always | Below 1 Ω |
| S7-1 (SLD+) or S1-4 - Other terminals and body ground | Always | 10 kΩ or higher |
| S7-5 (SLD-) - S1-1 | Always | Below 1 Ω |
| S7-5 (SLD-) or S1-1 - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the power seat tilt motor assembly (driver seat).
Click hereVehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>REMOVAL
Inspect the power seat tilt motor assembly (driver seat).
Click hereVehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the T7*1 and T6*1 or S7*2 and S6*2 position control ECU assembly (driver seat) connectors.
Disconnect the T9*1 or S9*2 power seat tilt motor assembly (driver seat) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
Check the wire harness and connector between the position control ECU assembly (driver seat) and applicable motor.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T7-7 (FRV+) - T9-1 | Always | Below 1 Ω |
| T7-7 (FRV+) or T9-1 - Other terminals and body ground | Always | 10 kΩ or higher |
| T6-4 (FRV-) - T9-4 | Always | Below 1 Ω |
| T6-4 (FRV-) or T9-4 - Other terminals and body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S7-7 (FRV+) - S9-1 | Always | Below 1 Ω |
| S7-7 (FRV+) or S9-1 - Other terminals and body ground | Always | 10 kΩ or higher |
| S6-4 (FRV-) - S9-4 | Always | Below 1 Ω |
| S6-4 (FRV-) or S9-4 - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the power seat lifter motor assembly (driver seat).
Click hereVehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>REMOVAL
Inspect the power seat lifter motor assembly (driver seat).
Click hereVehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the T7*1 and T6*1 or S7*2 and S6*2 position control ECU assembly (driver seat) connectors.
Disconnect the T12*1 or S12*2 power seat lifter motor assembly (driver seat) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
Check the wire harness and connector between the position control ECU assembly (driver seat) and applicable motor.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T7-6 (LFT+) - T12-1 | Always | Below 1 Ω |
| T7-6 (LFT+) or T12-1 - Other terminals and body ground | Always | 10 kΩ or higher |
| T6-5 (LFT-) - T12-4 | Always | Below 1 Ω |
| T6-5 (LFT-) or T12-4 - Other terminals and body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S7-6 (LFT+) - S12-1 | Always | Below 1 Ω |
| S7-6 (LFT+) or S12-1 - Other terminals and body ground | Always | 10 kΩ or higher |
| S6-5 (LFT-) - S12-4 | Always | Below 1 Ω |
| S6-5 (LFT-) or S12-4 - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the reclining motor (front seatback frame sub-assembly [driver seat]).
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY
Inspect the reclining motor (front seatback frame sub-assembly [driver seat]).
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the T7*1 and T6*1 or S7*2 and S6*2 position control ECU assembly (driver seat) connectors.
Disconnect the T23*1 or S23*2 reclining motor (front seatback frame sub-assembly [driver seat]) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
Check the wire harness and connector between the position control ECU assembly (driver seat) and applicable motor.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T7-10 (RCL+) - T23-1 | Always | Below 1 Ω |
| T7-10 (RCL+) or T23-1 - Other terminals and body ground | Always | 10 kΩ or higher |
| T6-6 (RCL-) - T23-4 | Always | Below 1 Ω |
| T6-6 (RCL-) or T23-4 - Other terminals and body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S7-10 (RCL+) - S23-1 | Always | Below 1 Ω |
| S7-10 (RCL+) or S23-1 - Other terminals and body ground | Always | 10 kΩ or higher |
| S6-6 (RCL-) - S23-4 | Always | Below 1 Ω |
| S6-6 (RCL-) or S23-4 - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the lumbar support adjuster assembly (driver seat).
Click hereVehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>REMOVAL
Inspect the lumbar support adjuster assembly (driver seat).
Click hereVehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the T7*1 and T6*1 or S7*2 and S6*2 position control ECU assembly (driver seat) connectors.
Disconnect the T24*1 or S24*2 lumbar support adjuster assembly (driver seat) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
Check the wire harness and connector between the position control ECU assembly (driver seat) and applicable motor.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T7-9 (L+) - T24-1 | Always | Below 1 Ω |
| T7-9 (L+) or T24-1 - Other terminals and body ground | Always | 10 kΩ or higher |
| T6-3 (L-) - T24-2 | Always | Below 1 Ω |
| T6-3 (L-) or T24-2 - Other terminals and body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S7-9 (L+) - S24-1 | Always | Below 1 Ω |
| S7-9 (L+) or S24-1 - Other terminals and body ground | Always | 10 kΩ or higher |
| S6-3 (L-) - S24-2 | Always | Below 1 Ω |
| S6-3 (L-) or S24-2 - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front power seat switch (driver seat).
Inspect the front power seat switch (driver seat).
Click hereVehicle Interior>SEAT>POWER SEAT SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the T8*1 or S8*2 position control ECU assembly (driver seat) connector.
Disconnect the T14*1 or S14*2 front power seat switch (driver seat) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T14-6 (SLDR) - T8-23 (SLDR) | Always | Below 1 Ω |
| T14-6 (SLDR) or T8-23 (SLDR) - Other terminals and body ground | Always | 10 kΩ or higher |
| T14-7 (SLDF) - T8-9 (SLDF) | Always | Below 1 Ω |
| T14-7 (SLDF) or T8-9 (SLDF) - Other terminals and body ground | Always | 10 kΩ or higher |
| T14-1 (RCLR) - T8-22 (RCLR) | Always | Below 1 Ω |
| T14-1 (RCLR) or T8-22 (RCLR) - Other terminals and body ground | Always | 10 kΩ or higher |
| T14-2 (RCLF) - T8-8 (RCLF) | Always | Below 1 Ω |
| T14-2 (RCLF) or T8-8 (RCLF) - Other terminals and body ground | Always | 10 kΩ or higher |
| T14-4 (FUP) - T8-6 (FRVU) | Always | Below 1 Ω |
| T14-4 (FUP) or T8-6 (FRVU) - Other terminals and body ground | Always | 10 kΩ or higher |
| T14-5 (FDWN) - T8-20 (FRVD) | Always | Below 1 Ω |
| T14-5 (FDWN) or T8-20 (FRVD) - Other terminals and body ground | Always | 10 kΩ or higher |
| T14-3 (LUP) - T8-7 (LFTU) | Always | Below 1 Ω |
| T14-3 (LUP) or T8-7 (LFTU) - Other terminals and body ground | Always | 10 kΩ or higher |
| T14-8 (LDWN) - T8-21 (LFTD) | Always | Below 1 Ω |
| T14-8 (LDWN) or T8-21 (LFTD) - Other terminals and body ground | Always | 10 kΩ or higher |
| T14-14 (H) - T8-4 (LFLF) | Always | Below 1 Ω |
| T14-14 (H) or T8-4 (LFLF) - Other terminals and body ground | Always | 10 kΩ or higher |
| T14-17 (R) - T8-18 (LFLR) | Always | Below 1 Ω |
| T14-17 (R) or T8-18 (LFLR) - Other terminals and body ground | Always | 10 kΩ or higher |
| T14-20 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S14-5 (SLDR) - S8-23 (SLDR) | Always | Below 1 Ω |
| S14-5 (SLDR) or S8-23 (SLDR) - Other terminals and body ground | Always | 10 kΩ or higher |
| S14-4 (SLDF) - S8-9 (SLDF) | Always | Below 1 Ω |
| S14-4 (SLDF) or S8-9 (SLDF) - Other terminals and body ground | Always | 10 kΩ or higher |
| S14-10 (RCLR) - S8-22 (RCLR) | Always | Below 1 Ω |
| S14-10 (RCLR) or S8-22 (RCLR) - Other terminals and body ground | Always | 10 kΩ or higher |
| S14-9 (RCLF) - S8-8 (RCLF) | Always | Below 1 Ω |
| S14-9 (RCLF) or S8-8 (RCLF) - Other terminals and body ground | Always | 10 kΩ or higher |
| S14-7 (FUP) - S8-6 (FRVU) | Always | Below 1 Ω |
| S14-7 (FUP) or S8-6 (FRVU) - Other terminals and body ground | Always | 10 kΩ or higher |
| S14-6 (FDWN) - S8-20 (FRVD) | Always | Below 1 Ω |
| S14-6 (FDWN) or S8-20 (FRVD) - Other terminals and body ground | Always | 10 kΩ or higher |
| S14-8 (LUP) - S8-7 (LFTU) | Always | Below 1 Ω |
| S14-8 (LUP) or S8-7 (LFTU) - Other terminals and body ground | Always | 10 kΩ or higher |
| S14-3 (LDWN) - S8-21 (LFTD) | Always | Below 1 Ω |
| S14-3 (LDWN) or S8-21 (LFTD) - Other terminals and body ground | Always | 10 kΩ or higher |
| S14-17 (H) - S8-4 (LFLF) | Always | Below 1 Ω |
| S14-17 (H) or S8-4 (LFLF) - Other terminals and body ground | Always | 10 kΩ or higher |
| S14-14 (R) - S8-18 (LFLR) | Always | Below 1 Ω |
| S14-14 (R) or S8-18 (LFLR) - Other terminals and body ground | Always | 10 kΩ or higher |
| S14-11 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG