Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY) › 2018.10–2020.05
RM3620E _51 Engine / Hybrid System _076333 HYBRID / BATTERY CONTROL _0374955 HYBRID CONTROL SYSTEM(for 2WD with NICKEL METAL HYDRIDE BATTERY) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 2WD with NICKEL METAL HYDRIDE BATTERY)  P0A8111  Hybrid/EV Battery Cooling Fan 1 Circuit Short to Ground  P0A814B  Hybrid/EV Battery Cooling Fan 1 Over Temperature  


DESCRIPTION

The battery cooling blower assembly speed is controlled by the hybrid vehicle control ECU assembly. Power is supplied to the battery cooling blower assembly when the MREL terminal of the hybrid vehicle control ECU assembly turns on the IGCT relay. The hybrid vehicle control ECU assembly sends command signals (SI0) to the battery cooling blower assembly to adjust the fan speed to an appropriate speed for the HV battery temperature. The frequency (FP0) of the battery cooling blower assembly is sent to the hybrid vehicle control ECU assembly via the battery voltage sensor as a monitor signal using serial communication.

A260101E39
0.521,0.208 2.594,0.646 2.073,0.438 10 false Battery Cooling Blower Assembly 2.792,0.958 4.417,1.323 1.625,0.365 10 false SI0 (Command Signal) 2.865,3.198 4.531,3.521 1.667,0.323 10 false FP0 (Monitor Signal) 4.875,0.385 5.792,1.021 0.917,0.635 10 false Hybrid Vehicle Control ECU Assembly 4.833,2.354 5.813,2.802 0.979,0.448 10 false Battery Voltage Sensor 3.896,1.729 5.281,2.01 1.385,0.281 10 false Serial Communication

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A8111 Hybrid/EV Battery Cooling Fan 1 Circuit Short to Ground Both of the following conditions are met:
·

The speed calculated based on the battery cooling blower assembly output frequency is not within the target control speed range.

·

The battery cooling blower assembly speed is excessively low when a certain level of speed is requested (possibility of an open or short to ground in connected circuits, or motor locking).


(2 trip detection logic)
·

Battery voltage sensor

·

Hybrid vehicle control ECU assembly

·

Battery cooling blower assembly

·

BATT FAN fuse

·

Wire harness or connector


Comes on Master Warning:
Comes on
P0A814B Hybrid/EV Battery Cooling Fan 1 Over Temperature Both of the following conditions are met:
·

The HV battery temperature is high and the speed calculated based on the battery cooling blower assembly output frequency is not within the target control speed range.

·

The HV battery temperature is high and the battery cooling blower assembly speed is excessively low when a certain level of speed is requested (possibility of an open or short to ground in connected circuits, or motor locking).


(1 trip detection logic)
·

Battery voltage sensor

·

Hybrid vehicle control ECU assembly

·

Battery cooling blower assembly

·

BATT FAN fuse

·

Wire harness or connector


Comes on Master Warning:
Comes on

Related Data List
DTC No. Data List
P0A8111
·

Hybrid Battery Cooling Fan 1 Drive Request

·

Hybrid Battery Cooling Fan 1 Drive Status

·

Hybrid Battery Cooling Fan 1 Frequency


P0A814B

The following items can be helpful when performing repairs:

Data List
·

Hybrid Battery Temperature 1 to 3

·

BATT Voltage


HINT:

"Hybrid Battery Cooling Fan 1 Frequency" is detected when the battery cooling blower assembly is operating and its value changes in proportion to the battery cooling blower assembly speed.


CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Control the Hybrid Battery Cooling Fan.

7.

Select fan mode 1 and operate the battery cooling blower assembly and wait for 60 seconds or more.

HINT:

Operation of the battery cooling blower assembly can be confirmed by checking if air is sucked into the air intake port of the intake duct.


8.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

9.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

for LHD:
A412342E10
1.073,0.146 3.292,0.635 2.219,0.49 10 false Auxiliary Battery 2.948,0.333 3.542,0.615 0.594,0.281 10 false IGCT 3.979,0.688 4.573,0.969 0.594,0.281 10 false IGCT 3.802,0.063 4.396,0.344 0.594,0.281 10 false 3 3.802,0.313 4.396,0.594 0.594,0.281 10 false 1 4.365,0.063 4.958,0.344 0.594,0.281 10 false 5 4.375,0.313 4.969,0.594 0.594,0.281 10 false 2 4.896,0.073 5.49,0.354 0.594,0.281 10 false 1 5.323,0.083 5.917,0.365 0.594,0.281 10 false 2 4.823,0.323 5.677,0.677 0.854,0.354 10 false BATT FAN 1.698,1.063 2.292,1.344 0.594,0.281 10 false MREL 1.854,1.5 2.448,1.781 0.594,0.281 10 false SI0 1.688,3.385 2.281,3.667 0.594,0.281 10 false BTH+ 1.698,3.719 2.292,4 0.594,0.281 10 false BTH- 1.25,4.417 1.844,4.698 0.594,0.281 10 false E01 1.25,4.771 1.844,5.052 0.594,0.281 10 false E02 0.885,4.427 1.479,4.708 0.594,0.281 10 false A31 0.917,4.24 1.51,4.521 0.594,0.281 10 false 12 0.906,4.604 1.5,4.885 0.594,0.281 10 false 11 0.875,4.771 1.469,5.052 0.594,0.281 10 false A31 2.177,3.375 2.771,3.656 0.594,0.281 10 false A31 2.229,3.542 2.823,3.823 0.594,0.281 10 false 42 2.229,3.198 2.823,3.479 0.594,0.281 10 false 41 2.188,3.719 2.781,4 0.594,0.281 10 false A31 0.792,5.219 3.406,5.573 2.615,0.354 10 false Hybrid Vehicle Control ECU Assembly 2.167,1.198 2.76,1.479 0.594,0.281 10 false A29 2.177,1.604 2.771,1.885 0.594,0.281 10 false A31 2.26,1.01 2.854,1.292 0.594,0.281 10 false 5 2.219,1.417 2.813,1.698 0.594,0.281 10 false 38 3.521,1.49 4.115,1.771 0.594,0.281 10 false SI0 3.323,1.5 3.917,1.781 0.594,0.281 10 false 4 4.417,1.49 5.01,1.771 0.594,0.281 10 false IG0 4.719,1.5 5.313,1.781 0.594,0.281 10 false 2 3.49,1.823 4.083,2.104 0.594,0.281 10 false GND0 3.344,1.823 3.938,2.104 0.594,0.281 10 false 3 4.375,1.823 4.969,2.104 0.594,0.281 10 false FP0 4.698,1.833 5.292,2.115 0.594,0.281 10 false 1 3.042,2.281 5.427,2.5 2.385,0.219 10 false M34 Battery Cooling Blower Assembly 5.885,1.823 6.479,2.104 0.594,0.281 10 false FP0 5.698,1.823 6.292,2.104 0.594,0.281 10 false 8 5.885,3.354 6.479,3.635 0.594,0.281 10 false BTH+ 5.688,3.26 6.281,3.542 0.594,0.281 10 false 2 5.688,3.604 6.281,3.885 0.594,0.281 10 false 3 5.906,3.698 6.5,3.979 0.594,0.281 10 false BTH- 5.635,5.271 6.083,5.438 0.448,0.167 10 false N17 5.646,5.438 7.156,5.635 1.51,0.198 10 false Battery Voltage Sensor 5.875,4.406 6.469,4.688 0.594,0.281 10 false GND 5.708,4.333 6.302,4.615 0.594,0.281 10 false 5

for RHD:
A412342E13
1.073,0.146 3.292,0.635 2.219,0.49 10 false Auxiliary Battery 2.948,0.333 3.542,0.615 0.594,0.281 10 false IGCT 3.979,0.688 4.573,0.969 0.594,0.281 10 false IGCT 3.802,0.063 4.396,0.344 0.594,0.281 10 false 3 3.802,0.313 4.396,0.594 0.594,0.281 10 false 1 4.365,0.063 4.958,0.344 0.594,0.281 10 false 5 4.375,0.313 4.969,0.594 0.594,0.281 10 false 2 4.896,0.073 5.49,0.354 0.594,0.281 10 false 1 5.323,0.083 5.917,0.365 0.594,0.281 10 false 2 4.823,0.323 5.677,0.677 0.854,0.354 10 false BATT FAN 1.698,1.063 2.292,1.344 0.594,0.281 10 false MREL 1.854,1.5 2.448,1.781 0.594,0.281 10 false SI0 1.688,3.385 2.281,3.667 0.594,0.281 10 false BTH+ 1.698,3.719 2.292,4 0.594,0.281 10 false BTH- 1.25,4.417 1.844,4.698 0.594,0.281 10 false E01 1.25,4.771 1.844,5.052 0.594,0.281 10 false E02 0.844,4.427 1.438,4.708 0.594,0.281 10 false G64 0.917,4.24 1.51,4.521 0.594,0.281 10 false 12 0.906,4.604 1.5,4.885 0.594,0.281 10 false 11 0.854,4.781 1.448,5.063 0.594,0.281 10 false G64 2.156,3.375 2.75,3.656 0.594,0.281 10 false G64 2.229,3.552 2.823,3.833 0.594,0.281 10 false 42 2.229,3.198 2.823,3.479 0.594,0.281 10 false 41 2.167,3.729 2.76,4.01 0.594,0.281 10 false G64 0.792,5.219 3.406,5.573 2.615,0.354 10 false Hybrid Vehicle Control ECU Assembly 2.167,1.198 2.76,1.479 0.594,0.281 10 false A29 2.177,1.604 2.771,1.885 0.594,0.281 10 false G64 2.26,1.01 2.854,1.292 0.594,0.281 10 false 5 2.219,1.417 2.813,1.698 0.594,0.281 10 false 38 3.521,1.49 4.115,1.771 0.594,0.281 10 false SI0 3.323,1.5 3.917,1.781 0.594,0.281 10 false 4 4.417,1.49 5.01,1.771 0.594,0.281 10 false IG0 4.719,1.5 5.313,1.781 0.594,0.281 10 false 2 3.49,1.823 4.083,2.104 0.594,0.281 10 false GND0 3.344,1.823 3.938,2.104 0.594,0.281 10 false 3 4.375,1.823 4.969,2.104 0.594,0.281 10 false FP0 4.698,1.833 5.292,2.115 0.594,0.281 10 false 1 3.042,2.281 5.427,2.5 2.385,0.219 10 false M34 Battery Cooling Blower Assembly 5.885,1.823 6.479,2.104 0.594,0.281 10 false FP0 5.698,1.823 6.292,2.104 0.594,0.281 10 false 8 5.885,3.354 6.479,3.635 0.594,0.281 10 false BTH+ 5.688,3.26 6.281,3.542 0.594,0.281 10 false 2 5.688,3.604 6.281,3.885 0.594,0.281 10 false 3 5.906,3.698 6.5,3.979 0.594,0.281 10 false BTH- 5.635,5.271 6.083,5.438 0.448,0.167 10 false N17 5.646,5.438 7.156,5.635 1.51,0.198 10 false Battery Voltage Sensor 5.875,4.406 6.469,4.688 0.594,0.281 10 false GND 5.708,4.333 6.302,4.615 0.594,0.281 10 false 5

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:

As the battery cooling blower assembly speed is excessively low, there is a possibility of an open or short to ground in connected circuits, or motor locking.


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397

Result:
Result Proceed to
P0AFC00 or P0AFC96 is not output. A
P0AFC00 or P0AFC96 is output. B


e.

Turn the power switch off.



A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE HYBRID BATTERY COOLING FAN)

B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE HYBRID BATTERY COOLING FAN)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Clear the DTCs and freeze frame data.

Powertrain > Hybrid Control > Clear DTCs
50002 397

e.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Control the Hybrid Battery Cooling Fan.

Powertrain > Hybrid Control > Active Test
Tester Display Measurement Item Control Range Restrict Condition
Control the Hybrid Battery Cooling Fan Change the battery cooling blower assembly operation and blower volume. 0, 1, 2, 3, 4, 5, 6 Intake air temperature -10°C (14°F) or higher
Powertrain > Hybrid Control > Active Test
Tester Display
Control the Hybrid Battery Cooling Fan
50004 397 2

f.

Select fan mode 6 in the "Control the Hybrid Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.

NOTICE:

If the Active Test cannot be performed, skip it and proceed to the next step to check if the fan operates and air is sucked in. In accordance with fail-safe system operation, the hybrid vehicle control ECU assembly sends a command to operate the battery cooling blower assembly.



g.

Check that the battery cooling blower assembly operates, air is sucked into the inlet duct and the operation sound is normal.

HINT:

The battery cooling blower assembly may not stop even when turning the cooling fan off in the "Control the Hybrid Battery Cooling Fan" Active Test. This is due to HV system control and is not a malfunction.


OK:

The battery cooling blower assembly operates.



h.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - BATTERY COOLING BLOWER ASSEMBLY)

NG

7.CHECK FUSE (BATT FAN)
3.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - BATTERY COOLING BLOWER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.

Disconnect the N17 battery voltage sensor connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
C404092N01
1.094,0.521 1.542,0.792 0.448,0.271 1.198,0.563 1.521,0.771 0.323,0.208 10 true M34

Disconnect the M34 battery cooling blower assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



e.
A368047C17
1.448,2.125 1.906,2.396 0.458,0.271 0.781,3.542 1.24,3.813 0.458,0.271 1.896,3.51 2.354,3.281 true 1.906,2.635 2.365,2.406 true 0.135,0.115 0.594,0.604 0.458,0.49 10 false *a 0.24,3.021 0.604,3.323 0.365,0.302 10 false *b 0.865,3.594 1.385,3.896 0.521,0.302 10 false M34 1.563,2.188 2.083,2.49 0.521,0.302 10 false N17 2.427,3.156 2.792,3.458 0.365,0.302 10 false FP0 1.615,2.604 1.979,2.906 0.365,0.302 10 false FP0
*a Rear view of wire harness connector
(to Battery Voltage Sensor)
*b Front view of wire harness connector
(to Battery Cooling Blower Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N17-8 (FP0) - M34-1 (FP0) Power switch off Below 1 Ω
N17-8 (FP0) - Body ground and other terminals Power switch off 10 kΩ or higher



f.

Connect the cable to the negative (-) auxiliary battery terminal.


g.

Turn the power switch on (IG).


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
N17-8 (FP0) - Body ground Power switch on (IG) Below 1 V


NOTICE:
·

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.



HINT:

As there might be an intermittent malfunction, inspect the following items even if the measured voltage is as specified.

Check that each connector between the battery voltage sensor and battery cooling blower assembly is not loose or disconnected.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.


k.

Reconnect the M34 battery cooling blower assembly connector.


l.

Reconnect the N17 battery voltage sensor connector.


m.

Install the No. 1 hybrid battery exhaust duct.


Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (COOLING FAN FREQUENCY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (COOLING FAN FREQUENCY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Connect the GTS to the DLC3.


e.

Turn the power switch on (IG).


f.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


g.

Clear the DTCs and freeze frame data.

Powertrain > Hybrid Control > Clear DTCs
50002 397

h.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Control the Hybrid Battery Cooling Fan.

Powertrain > Hybrid Control > Active Test
Tester Display Measurement Item Control Range Restrict Condition
Control the Hybrid Battery Cooling Fan Change the battery cooling blower assembly operation and blower volume. 0, 1, 2, 3, 4, 5, 6 Intake air temperature -10°C (14°F) or higher
Powertrain > Hybrid Control > Active Test
Tester Display
Control the Hybrid Battery Cooling Fan
50004 397 2

i.

Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid Battery Cooling Fan 1 Frequency.

Powertrain > Hybrid Control > Data List
Tester Display
Hybrid Battery Cooling Fan 1 Frequency
50003 397 157

j.

Select each fan mode 1 to 6 in the "Control the Hybrid Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.

NOTICE:

If the Active Test cannot be performed, skip it and proceed to the next step to check the frequency value. In accordance with fail-safe system operation, the hybrid vehicle control ECU assembly sends a command to operate the battery cooling fan assembly.



k.
C408110C03
2.167,0.156 2.604,0.385 0.438,0.229 1.719,1.635 2.26,0.948 true 2.781,1.698 2.49,0.958 true 0.104,0.063 0.5,0.375 0.396,0.313 10 false *a 2.26,0.177 2.656,0.49 0.396,0.313 10 false N17 1.552,1.656 1.885,1.917 0.333,0.26 10 false FP0 2.688,1.719 3.021,1.979 0.333,0.26 10 false GND
*a Component with harness connected
(Battery Voltage Sensor)


While the cooling fan is operating, compare the value in the Data List (Hybrid Battery Cooling Fan 1 Frequency) with the frequency value that was actually measured at the battery voltage sensor connector.

Specified Condition:
Tester Connection Condition
N17-8 (FP0) - N17-5 (GND) Battery cooling blower assembly is operating.


NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.


HINT:

Compare the values in each fan mode 1 to 6. If the Active Test cannot be performed, compare the values only in the current fan mode.



Result:
Result Proceed to
Both of the values in the Data List (Hybrid Battery Cooling Fan 1 Frequency) and the actual measured value at the battery voltage sensor connector are 0 Hz. A
Other than above B


l.

Turn the power switch off.


m.

Disconnect the cable from the negative (-) auxiliary battery terminal.


n.

Install the No. 1 hybrid battery exhaust duct.



A

5.CHECK BATTERY VOLTAGE SENSOR

B

6.CHECK BATTERY VOLTAGE SENSOR (FREQUENCY)
5.CHECK BATTERY VOLTAGE SENSOR
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the rear seat cushion leg sub-assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY BLOWER>REMOVAL


c.
C404092N01
1.094,0.521 1.542,0.792 0.448,0.271 1.198,0.563 1.521,0.771 0.323,0.208 10 true M34

Disconnect the M34 battery cooling blower assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).


f.
A369910C79
1.583,0.354 2.021,0.635 0.438,0.281 1.99,0.99 2.448,0.729 true 1.99,1.229 2.479,1.521 true 0.229,0.135 0.813,0.76 0.583,0.625 10 false *a 1.667,0.385 2.323,0.906 0.656,0.521 10 false M34 2.531,0.594 3.115,1.219 0.583,0.625 10 false FP0 2.552,1.531 3.104,1.844 0.552,0.313 10 false GND0
*a Front view of wire harness connector
(to Battery Cooling Blower Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M34-1 (FP0) - M34-3 (GND0) Power switch on (IG) 4.5 to 5.5 V


NOTICE:
·

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.




g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Reconnect the M34 battery cooling blower assembly connector.


j.

Install the rear seat cushion leg sub-assembly.


Result:
Proceed to
OK
NG



OK

REPLACE BATTERY COOLING BLOWER ASSEMBLY

NG

6.CHECK BATTERY VOLTAGE SENSOR (FREQUENCY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Connect the GTS to the DLC3.


e.

Turn the power switch on (IG).


f.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


g.

Clear the DTCs and freeze frame data.

Powertrain > Hybrid Control > Clear DTCs
50002 397

h.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Control the Hybrid Battery Cooling Fan.

Powertrain > Hybrid Control > Active Test
Tester Display Measurement Item Control Range Restrict Condition
Control the Hybrid Battery Cooling Fan Change the battery cooling blower assembly operation and blower volume. 0, 1, 2, 3, 4, 5, 6 Intake air temperature -10°C (14°F) or higher
Powertrain > Hybrid Control > Active Test
Tester Display
Control the Hybrid Battery Cooling Fan
50004 397 2

i.

Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid Battery Cooling Fan 1 Frequency.

Powertrain > Hybrid Control > Data List
Tester Display
Hybrid Battery Cooling Fan 1 Frequency
50003 397 157

j.

Select each fan mode 1 to 6 in the "Control the Hybrid Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.

NOTICE:

If the Active Test cannot be performed, skip it and proceed to the next step to check the frequency value. In accordance with fail-safe system operation, the hybrid vehicle control ECU assembly sends a command to operate the battery cooling blower assembly.



k.
C408110C04
2.167,0.156 2.604,0.385 0.438,0.229 1.719,1.635 2.26,0.948 true 2.781,1.698 2.49,0.958 true 0.104,0.063 0.5,0.375 0.396,0.313 10 false *a 2.26,0.177 2.656,0.49 0.396,0.313 10 false N17 1.552,1.656 1.885,1.917 0.333,0.26 10 false FP0 2.688,1.719 3.021,1.979 0.333,0.26 10 false GND
*a Component with harness connected
(Battery Voltage Sensor)


While the cooling fan is operating, compare the value in the Data List (Hybrid Battery Cooling Fan 1 Frequency) with the frequency value that was actually measured at the battery voltage sensor connector.

Specified Condition:
Tester Connection Condition Specified Condition
N17-8 (FP0) - N17-5 (GND) Battery cooling blower assembly is operating. Difference between the value in the Data List (Hybrid Battery Cooling Fan 1 Frequency) and the actual measured value at the battery voltage sensor connector is 10% or less.


NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.


HINT:

Compare the values in each fan mode 1 to 6. If the Active Test cannot be performed, compare the values only in the current fan mode.



Result:
Proceed to
OK
NG


l.

Turn the power switch off.


m.

Disconnect the cable from the negative (-) auxiliary battery terminal.


n.

Install the No. 1 hybrid battery exhaust duct.



OK

REPLACE BATTERY COOLING BLOWER ASSEMBLY

NG

7.CHECK FUSE (BATT FAN)
a.
C408044C01
1.073,2.438 1.521,2.646 true 0.156,0.146 0.469,0.344 0.313,0.198 10 false *1 0.885,2.292 1.198,2.49 0.313,0.198 10 false *2
*1 No. 3 Relay Block and Junction Block Assembly
*2 BATT FAN Fuse


Remove the BATT FAN fuse from the No. 3 relay block and junction block assembly.


b.

Measure the resistance of the BATT FAN fuse.

Standard Resistance:
Tester Connection Condition Specified Condition
BATT FAN fuse Power switch off Below 1 Ω



c.

Install the BATT FAN fuse.


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (IGCT RELAY - BATTERY COOLING BLOWER ASSEMBLY) (VOLTAGE)

NG

17.CHECK HARNESS AND CONNECTOR (BATT FAN FUSE - BATTERY COOLING BLOWER ASSEMBLY)
8.CHECK HARNESS AND CONNECTOR (IGCT RELAY - BATTERY COOLING BLOWER ASSEMBLY) (VOLTAGE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the rear seat cushion leg sub-assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY BLOWER>REMOVAL


c.
C404092N01
1.094,0.521 1.542,0.792 0.448,0.271 1.198,0.563 1.521,0.771 0.323,0.208 10 true M34

Disconnect the M34 battery cooling blower assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Connect the GTS to the DLC3.


f.

Turn the power switch on (IG).


g.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


h.

Clear the DTCs and freeze frame data.

Powertrain > Hybrid Control > Clear DTCs
50002 397

i.
A369910C80
1.583,0.354 2.021,0.635 0.438,0.281 1.042,0.781 1.583,1 true 2,1.188 2.542,1.406 true 0.229,0.135 0.813,0.76 0.583,0.625 10 false *a 1.635,0.406 2.292,0.927 0.656,0.521 10 false M34 0.729,0.688 1.313,1.313 0.583,0.625 10 false IG0 2.563,1.438 3.198,1.729 0.635,0.292 10 false GND0
*a Front view of wire harness connector
(to Battery Cooling Blower Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M34-2 (IG0) - M34-3 (GND0) Power switch on (IG) 11 to 14 V


NOTICE:
·

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.



HINT:

As there might be an intermittent malfunction, inspect the following items even if the measured voltage is as specified.

·

Installation condition of fuse(s) (before removing fuse(s)) (IG circuit)

·

Fuse condition (before and after removing fuse(s)) (IG circuit)

·

Connection condition of connectors (IG circuit)

·

Wire harness condition (IG circuit)

·

Wire harness condition (GND circuit)




j.

Turn the power switch off.


k.

Disconnect the cable from the negative (-) auxiliary battery terminal.


l.

Reconnect the M34 battery cooling blower assembly connector.


m.

Install the rear seat cushion leg sub-assembly.


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - BATTERY COOLING BLOWER ASSEMBLY)

NG

13.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER ASSEMBLY - BODY GROUND)
9.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - BATTERY COOLING BLOWER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A31*1, G64*2 hybrid vehicle control ECU assembly connector.

*1: for LHD

*2: for RHD


NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check that each connector between the hybrid vehicle control ECU assembly and battery cooling blower assembly is not loose or disconnected.




c.

Remove the rear seat cushion leg sub-assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY BLOWER>REMOVAL


d.
C404092N01
1.094,0.521 1.542,0.792 0.448,0.271 1.198,0.563 1.521,0.771 0.323,0.208 10 true M34

Disconnect the M34 battery cooling blower assembly connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check the terminals of the connector for deformation and corrosion.




e.
A369911C14
1.49,2.885 1.896,3.156 0.406,0.271 1.438,0.271 1.844,0.542 0.406,0.271 1,3.906 1.5,3.771 true 1.135,1.646 0.802,2.25 true 0.292,0.375 0.74,0.771 0.448,0.396 10 false *a 0.396,2.917 0.813,3.198 0.417,0.281 10 false *b 1.563,2.917 2.073,3.26 0.51,0.344 10 false M34 0.74,3.865 1.156,4.146 0.417,0.281 10 false SI0 1.531,0.302 2.042,0.646 0.51,0.344 10 false A31 0.667,2.313 1.083,2.594 0.417,0.281 10 false SI0 0.125,0.115 0.438,0.313 0.313,0.198 10 false *A
*A for LHD
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)
*b Front view of wire harness connector
(to Battery Cooling Blower Assembly)


for LHD:

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A31-38 (SI0) - M34-4 (SI0) Power switch off Below 1 Ω
M34-4 (SI0) - Body ground and other terminals Power switch off 10 kΩ or higher


NOTICE:

Make sure that each connector between the hybrid vehicle control ECU assembly and battery cooling blower assembly is not loose or disconnected and its terminals are not deformed or corroded.



f.
A369911C13
1.49,2.885 1.896,3.156 0.406,0.271 1.438,0.271 1.844,0.542 0.406,0.271 1,3.906 1.5,3.771 true 1.135,1.646 0.802,2.25 true 0.333,0.333 0.781,0.729 0.448,0.396 10 false *a 0.427,2.906 0.844,3.188 0.417,0.281 10 false *b 1.563,2.917 2.073,3.26 0.51,0.344 10 false M34 0.74,3.865 1.156,4.146 0.417,0.281 10 false SI0 1.531,0.302 2.042,0.646 0.51,0.344 10 false G64 0.667,2.313 1.083,2.594 0.417,0.281 10 false SI0 0.125,0.146 0.438,0.344 0.313,0.198 10 false *A
*A for RHD
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)
*b Front view of wire harness connector
(to Battery Cooling Blower Assembly)


for RHD:

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G64-38 (SI0) - M34-4 (SI0) Power switch off Below 1 Ω
M34-4 (SI0) - Body ground and other terminals Power switch off 10 kΩ or higher


NOTICE:

Make sure that each connector between the hybrid vehicle control ECU assembly and battery cooling blower assembly is not loose or disconnected and its terminals are not deformed or corroded.



g.

Connect the cable to the negative (-) auxiliary battery terminal.


h.

Turn the power switch on (IG).


i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M34-4 (SI0) - Body ground Power switch on (IG) Below 1 V


NOTICE:
·

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.



HINT:

As there might be an intermittent malfunction, inspect the following items even if the measured voltage is as specified.

Check that each connector between the hybrid vehicle control ECU assembly and battery cooling blower assembly is not loose or disconnected.



j.

Turn the power switch off.


k.

Disconnect the cable from the negative (-) auxiliary battery terminal.


l.

Reconnect the M34 battery cooling blower assembly connector.


m.

Install the rear seat cushion leg sub-assembly.


n.

Reconnect the A31*1, G64*2 hybrid vehicle control ECU assembly connector.

*1: for LHD

*2: for RHD



Result:
Proceed to
OK
NG



OK

10.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY
a.

Remove the hybrid vehicle control ECU assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID VEHICLE CONTROL ECU>REMOVAL


b.

for LHD:

Measure the resistance according to the value(s) in the table below.

A365590C35
3.417,0.354 3.771,0.604 0.354,0.25 2.865,1.281 1.906,0.521 true 4.042,1.604 3.667,2.375 true 0.094,0.083 0.406,0.281 0.313,0.198 10 false *A 3.469,0.385 4.021,0.865 0.552,0.479 10 false A31 1.594,0.417 2.208,0.615 0.615,0.198 10 false E01 3.542,2.417 4.083,2.698 0.542,0.281 10 false SI0 0.292,0.271 0.604,0.469 0.313,0.198 10 false *a
*A for LHD - -
*a Component without harness connected
(Hybrid Vehicle Control ECU Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
A31-38 (SI0) - A31-12 (E01) Power switch off 10 kΩ or higher



c.

for RHD:

Measure the resistance according to the value(s) in the table below.

A365590C32
3.417,0.354 3.771,0.604 0.354,0.25 2.865,1.281 1.906,0.521 true 4.042,1.604 3.667,2.375 true 0.333,0.229 0.646,0.427 0.313,0.198 10 false *a 3.469,0.385 4.021,0.865 0.552,0.479 10 false G64 1.594,0.417 2.208,0.615 0.615,0.198 10 false E01 3.542,2.417 4.083,2.698 0.542,0.281 10 false SI0 0.094,0.063 0.406,0.26 0.313,0.198 10 false *A
*A for RHD - -
*a Component without harness connected
(Hybrid Vehicle Control ECU Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
G64-38 (SI0) - G64-12 (E01) Power switch off 10 kΩ or higher



d.

Install the hybrid vehicle control ECU assembly.


Result:
Proceed to
OK
NG



OK

11.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (SI0 VOLTAGE)

NG

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

11.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (SI0 VOLTAGE)
a.

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

for LHD:

Measure the voltage according to the value(s) in the table below.

C407546C33
3.354,0.354 3.76,0.635 0.406,0.281 4.031,1.594 4.583,2.25 true 2.573,0.469 2.865,1.25 true 0.302,0.24 0.719,0.542 0.417,0.302 10 false *a 3.448,0.385 3.906,0.635 0.458,0.25 10 false A31 4.552,2.281 5.01,2.531 0.458,0.25 10 false SI0 2.396,0.24 2.771,0.469 0.375,0.229 10 false E01 0.094,0.083 0.51,0.385 0.417,0.302 10 false *A
*A for LHD - -
*a Component with harness connected
(Hybrid Vehicle Control ECU Assembly)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
A31-38 (SI0) - A31-12 (E01) Power switch on (IG) 4.5 to 5.5 V



d.

for RHD:

Measure the voltage according to the value(s) in the table below.

C407546C29
3.354,0.354 3.76,0.635 0.406,0.281 4.031,1.594 4.583,2.25 true 2.573,0.469 2.865,1.25 true 0.292,0.292 0.708,0.594 0.417,0.302 10 false *a 3.448,0.385 3.906,0.635 0.458,0.25 10 false G64 4.552,2.281 5.01,2.531 0.458,0.25 10 false SI0 2.396,0.24 2.771,0.469 0.375,0.229 10 false E01 0.115,0.094 0.531,0.396 0.417,0.302 10 false *A
*A for RHD - -
*a Component with harness connected
(Hybrid Vehicle Control ECU Assembly)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
G64-38 (SI0) - G64-12 (E01) Power switch on (IG) 4.5 to 5.5 V



e.

Turn the power switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.


Result:
Proceed to
OK
NG



OK

12.CHECK BATTERY COOLING BLOWER ASSEMBLY

NG

REPLACE BATTERY COOLING BLOWER ASSEMBLY

12.CHECK BATTERY COOLING BLOWER ASSEMBLY
a.

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


e.

Clear the DTCs and freeze frame data.

Powertrain > Hybrid Control > Clear DTCs
50002 397

f.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Control the Hybrid Battery Cooling Fan.

Powertrain > Hybrid Control > Active Test
Tester Display Measurement Item Control Range Restrict Condition
Control the Hybrid Battery Cooling Fan Change the battery cooling blower assembly operation and blower volume. 0, 1, 2, 3, 4, 5, 6 Intake air temperature -10°C (14°F) or higher
Powertrain > Hybrid Control > Active Test
Tester Display
Control the Hybrid Battery Cooling Fan
50004 397 2

g.

Select each fan mode 1 to 6 in the "Control the Hybrid Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.

NOTICE:

If the Active Test cannot be performed, skip it and proceed to the next step to check the waveform. In accordance with fail-safe system operation, the hybrid vehicle control ECU assembly sends a command to operate the battery cooling blower assembly.



h.

for LHD:

Connect an oscilloscope to the A31 hybrid vehicle control ECU assembly connector and check the waveform.

Item Content
Tester Connection A31-38 (SI0) - A31-12 (E01)
Equipment Setting 10 V/DIV., 1 ms./DIV.
Condition Power switch on (IG), during Active Test

HINT:
·

Perform this inspection with the hybrid vehicle control ECU assembly connector connected.

·

The wave length will vary with the operating speed of the battery cooling blower assembly.



C407546C34
3.354,0.354 3.76,0.635 0.406,0.281 4.031,1.594 4.583,2.25 true 2.573,0.469 2.865,1.25 true 0.271,0.26 0.688,0.563 0.417,0.302 10 false *a 3.448,0.385 3.906,0.635 0.458,0.25 10 false A31 4.552,2.281 5.01,2.531 0.458,0.25 10 false SI0 2.396,0.24 2.771,0.469 0.375,0.229 10 false E01 0.094,0.073 0.51,0.375 0.417,0.302 10 false *A
*A for LHD - -
*a Component with harness connected
(Hybrid Vehicle Control ECU Assembly)
- -



i.

for RHD:

Connect an oscilloscope to the G64 hybrid vehicle control ECU assembly connector and check the waveform.

Item Content
Tester Connection G64-38 (SI0) - G64-12 (E01)
Equipment Setting 10 V/DIV., 1 ms./DIV.
Condition Power switch on (IG), during Active Test

HINT:
·

Perform this inspection with the hybrid vehicle control ECU assembly connector connected.

·

The wave length will vary with the operating speed of the battery cooling blower assembly.



C407546C30
3.354,0.354 3.76,0.635 0.406,0.281 4.031,1.594 4.583,2.25 true 2.573,0.469 2.865,1.25 true 0.24,0.271 0.656,0.573 0.417,0.302 10 false *a 3.417,0.417 3.875,0.667 0.458,0.25 10 false G64 4.552,2.281 5.01,2.531 0.458,0.25 10 false SI0 2.396,0.24 2.771,0.469 0.375,0.229 10 false E01 0.104,0.083 0.521,0.385 0.417,0.302 10 false *A
*A for RHD - -
*a Component with harness connected
(Hybrid Vehicle Control ECU Assembly)
- -



j.

Turn the power switch off.


k.
A284431C04
2.938,1.031 3.396,1.229 0.458,0.198 10 false GND 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a
*a Waveform 1


Disconnect the cable from the negative (-) auxiliary battery terminal.


Result:
Result Proceed to
Normal (The pulse output of waveform 1) A
No pulse generation B



A

REPLACE BATTERY COOLING BLOWER ASSEMBLY

B

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

13.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER ASSEMBLY - BODY GROUND)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the rear seat cushion leg sub-assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY BLOWER>REMOVAL


c.
C404092N01
1.094,0.521 1.542,0.792 0.448,0.271 1.198,0.563 1.521,0.771 0.323,0.208 10 true M34

Disconnect the M34 battery cooling blower assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A369910C81
1.583,0.354 2.021,0.635 0.438,0.281 1.969,1.229 2.51,1.448 true 0.229,0.135 0.813,0.76 0.583,0.625 10 false *a 1.667,0.385 2.323,0.906 0.656,0.521 10 false M34 2.583,1.427 3.219,1.813 0.635,0.385 10 false GND0
*a Front view of wire harness connector
(to Battery Cooling Blower Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M34-3 (GND0) - Body ground Power switch off Below 1 Ω



e.

Connect the M34 battery cooling blower assembly connector.


f.

Install the rear seat cushion leg sub-assembly.


Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - BODY GROUND)
a.

Disconnect the A31*1, G64*2 hybrid vehicle control ECU assembly connector.

*1: for LHD

*2: for RHD


NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



b.
C411164C01
1.469,0.073 1.896,0.333 0.427,0.26 2.719,1.094 2.927,0.365 true 1.563,0.135 2.042,0.458 0.479,0.323 10 false A31 2.979,0.25 3.385,0.51 0.406,0.26 10 false E01 0.115,0.083 0.521,0.344 0.406,0.26 10 false *A 0.323,0.26 0.729,0.521 0.406,0.26 10 false *a
*A for LHD
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)


for LHD:

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A31-12 (E01) - Body ground Power switch off Below 1 Ω



c.
C411164C02
1.563,0.135 1.917,0.385 0.354,0.25 2.708,1.094 2.896,0.333 true 1.615,0.167 2.073,0.365 0.458,0.198 10 false G64 2.906,0.135 3.365,0.333 0.458,0.198 10 false E01 0.135,0.083 0.448,0.281 0.313,0.198 10 false *A 0.313,0.333 0.625,0.531 0.313,0.198 10 false *a
*A for RHD
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)


for RHD:

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G64-12 (E01) - Body ground Power switch off Below 1 Ω



d.

Reconnect the A31*1, G64*2 hybrid vehicle control ECU assembly connector.

*1: for LHD

*2: for RHD



Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - BODY GROUND)
a.

Disconnect the A31*1, G64*2 hybrid vehicle control ECU assembly connector.

*1: for LHD

*2: for RHD


NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



b.
C411164C04
1.469,0.073 1.896,0.333 0.427,0.26 2.573,1.083 2.823,0.365 true 1.542,0.115 2.021,0.438 0.479,0.323 10 false A31 2.875,0.25 3.281,0.51 0.406,0.26 10 false E02 0.365,0.229 0.677,0.427 0.313,0.198 10 false *a 0.094,0.063 0.406,0.26 0.313,0.198 10 false *A
*A for LHD
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)


for LHD:

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A31-11 (E02) - Body ground Power switch off Below 1 Ω



c.
C411164C05
1.51,0.125 1.896,0.365 0.385,0.24 2.552,1.083 2.844,0.427 true 1.573,0.156 2.031,0.354 0.458,0.198 10 false G64 2.885,0.208 3.344,0.406 0.458,0.198 10 false E02 0.135,0.104 0.448,0.302 0.313,0.198 10 false *A 0.406,0.271 0.719,0.469 0.313,0.198 10 false *a
*A for RHD
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)


for RHD:

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G64-11 (E02) - Body ground Power switch off Below 1 Ω



d.

Reconnect the A31*1, G64*2 hybrid vehicle control ECU assembly connector.

*1: for LHD

*2: for RHD



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (IGCT RELAY - BATTERY COOLING BLOWER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (IGCT RELAY - BATTERY COOLING BLOWER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the IGCT relay from the No. 3 relay block and junction block assembly.

NOTICE:

Check the terminals of the relay for deformation and corrosion.



c.

Remove the rear seat cushion leg sub-assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY BLOWER>REMOVAL


d.
C404092N01
1.094,0.521 1.542,0.792 0.448,0.271 1.198,0.563 1.521,0.771 0.323,0.208 10 true M34

Disconnect the M34 battery cooling blower assembly connector.

NOTICE:
·

Check that each connector between the IGCT relay and battery cooling blower assembly is not loose or disconnected.

·

Before disconnecting the connector, check that it is not loose or disconnected.




e.

Measure the resistance according to the value(s) in the table below.

C408045C01
0.635,1.781 1.01,2.01 0.375,0.229 1.698,1.677 1.385,1.333 true 0.479,0.365 0.792,0.563 0.313,0.198 10 false *a 3.708,0.323 4.021,0.521 0.313,0.198 10 false *1 5.646,1.854 5.958,2.052 0.313,0.198 10 false *2 0.708,1.813 1.167,2.01 0.458,0.198 10 false M34 1.146,1.177 1.604,1.375 0.458,0.198 10 false IG0
*1 No. 3 Relay Block and Junction Block Assembly *2 IGCT Relay Terminal
*a Front view of wire harness connector
(to Battery Cooling Blower Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
M34-2 (IG0) - 5 (IGCT relay) Power switch off Below 1 Ω


NOTICE:
·

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.

·

Check that each connector between the IGCT relay and battery cooling blower assembly is not loose or disconnected.




f.

Reconnect the M34 battery cooling blower assembly connector.


g.

Install the rear seat cushion leg sub-assembly.


h.

Install the IGCT relay to the No. 3 relay block and junction block assembly.


Result:
Proceed to
OK
NG



OK

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (BATT FAN FUSE - BATTERY COOLING BLOWER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the BATT FAN fuse from the No. 3 relay block and junction block assembly.


c.

Remove the rear seat cushion leg sub-assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY BLOWER>REMOVAL


d.
C404092N01
1.094,0.521 1.542,0.792 0.448,0.271 1.198,0.563 1.521,0.771 0.323,0.208 10 true M34

Disconnect the M34 battery cooling blower assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



e.

Measure the resistance according to the value(s) in the table below.

C408046C01
0.729,1.74 1.073,2 0.344,0.26 1.698,1.667 1.563,1.313 true 0.292,0.375 0.604,0.573 0.313,0.198 10 false *a 3.688,0.24 4,0.438 0.313,0.198 10 false *1 5.354,2.615 5.667,2.813 0.313,0.198 10 false *2 0.771,1.781 1.229,1.979 0.458,0.198 10 false M34 1.385,1.104 1.844,1.302 0.458,0.198 10 false IG0
*1 No. 3 Relay Block and Junction Block Assembly *2 BATT FAN Fuse Terminal
*a Front view of wire harness connector
(to Battery Cooling Blower Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
M34-2 (IG0) - Terminals other than 2 (BATT FAN fuse terminal) and body ground Power switch off 10 kΩ or higher


NOTICE:

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.



f.

Reconnect the M34 battery cooling blower assembly connector.


g.

Install the rear seat cushion leg sub-assembly.


h.

Install the BATT FAN fuse to the No. 3 relay block and junction block assembly.


Result:
Proceed to
OK
NG



OK

18.CHECK BATTERY COOLING BLOWER ASSEMBLY

NG

20.REPAIR OR REPLACE HARNESS OR CONNECTOR
18.CHECK BATTERY COOLING BLOWER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the rear seat cushion leg sub-assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY BLOWER>REMOVAL


c.
C404092N01
1.094,0.521 1.542,0.792 0.448,0.271 1.198,0.563 1.521,0.771 0.323,0.208 10 true M34

Disconnect the M34 battery cooling blower assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A369912C19
1.552,0.281 1.938,0.583 0.385,0.302 0.99,1.479 1.552,1.229 true 1.938,0.979 2.5,0.729 true 0.208,0.115 0.781,0.625 0.573,0.51 10 false *a 1.615,0.313 2.188,0.823 0.573,0.51 10 false M34 2.583,0.635 3.156,1.146 0.573,0.51 10 false IG0 0.531,1.396 1.104,1.906 0.573,0.51 10 false GND0
*a Component without harness connected
(Battery Cooling Blower Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M34-2 (IG0) - M34-3 (GND0) and Body ground Power switch off 10 kΩ or higher


NOTICE:

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.



e.

Reconnect the M34 battery cooling blower assembly connector.


f.

Install the rear seat cushion leg sub-assembly.


Result:
Proceed to
OK
NG



OK

REPLACE FUSE (BATT FAN)

NG

19.REPLACE BATTERY COOLING BLOWER ASSEMBLY
19.REPLACE BATTERY COOLING BLOWER ASSEMBLY

NEXT

REPLACE FUSE (BATT FAN)

20.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (BATT FAN)