Home › Drivetrain › Q610 (HYBRID TRANSMISSION / TRANSAXLE) › REAR TRACTION MOTOR › 2019.02–2020.05
RM3620E _52 Drivetrain _080124 Q610 HYBRID TRANSMISSION / TRANSAXLE _0388721 REAR TRACTION MOTOR A

Q610 HYBRID TRANSMISSION / TRANSAXLE  REAR TRACTION MOTOR  INSTALLATION  


PROCEDURE

Hide G1050C 1.INSTALL REAR TRACTION MOTOR FILLER PLUG

HINT:

There is no need to remove this unless the rear traction motor filler plug is replaced.


a.

Using a 10 mm hexagon socket wrench, install the rear traction motor filler plug and a new gasket to the rear traction motor with transaxle assembly.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)


Hide 52380F 2.TEMPORARILY INSTALL FRONT DIFFERENTIAL SUPPORT ASSEMBLY

a.

Temporarily install the front differential support assembly to the rear traction motor with transaxle assembly with 2 new bolts.

HINT:

Bolt Length: 55 mm (2.17 in.)



Hide 3.INSTALL WIRE HARNESS CLAMP BRACKET

a.
C407285C01
0,0 0,0 false
V100135

Bolt A
V100136

Bolt B


Install the 3 wire harness clamp brackets to the rear traction motor with transaxle assembly with the 4 bolts.

Torque:
for bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for bolt B : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide G1050 4.INSTALL REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY

a.

Using an engine sling device and chain block, hold the rear traction motor with transaxle assembly.

CAUTION:
·

Do not lift the rear traction motor with transaxle assembly more than necessary.

·

Check the center of gravity while lifting the rear traction motor with transaxle assembly.



NOTICE:
·

Do not drop the rear traction motor with transaxle assembly.

·

Do not damage the installation surface of the rear traction motor with transaxle assembly.




b.
C407298C01
0.375,2.875 0.521,2.875 0.521,2.875 0.573,3.042 false 0.26,4.177 0.26,4.083 0.26,4.083 0.438,3.969 false 0.198,2.802 0.385,3.031 0.188,0.229 10 false *1 0.177,4.198 0.396,4.406 0.219,0.208 10 false *2
*1 Upper Differential Mount Stopper
*2 Lower Differential Mount Stopper
V100135

Bolt A
V100136

Bolt B


Temporarily install the 2 upper differential mount stoppers and 2 lower differential mount stoppers, rear traction motor with transaxle assembly to the rear suspension member sub-assembly with 3 new bolts.

HINT:
Bolt Bolt Length
A 110 mm (4.33 in.)
B 45 mm (1.77 in.)



c.
C407303C01
1.25,2.375 1.479,2.375 1.479,2.375 1.979,2.792 true 2.021,3.021 2.729,2.802 2.729,2.802 2.917,2.802 true 1.052,2.271 1.271,2.521 0.219,0.25 10 false *a 2.938,2.719 3.188,2.969 0.25,0.25 10 false *b
*a Inner Cylinder Mark
*b Rubber Part Mark
V100135

Bolt A
V100136

Bolt B
V100137

Bolt C


Tighten the 5 bolts.

Torque:
for bolt A : 86 N*m (877 kgf*cm, 63 ft.*lbf)
for bolt B : 130 N*m (1326 kgf*cm, 96 ft.*lbf)
for bolt C : 55 N*m (561 kgf*cm, 41 ft.*lbf)

NOTICE:

After tightening bolt B, make sure that the inner cylinder mark and rubber part mark are positioned as shown in the illustration.


HINT:

Tightening order: Tighten bolt (C) → Tighten bolt (B) → Tighten bolt (A)



d.

Remove the engine sling device and chain block.


Hide 5.CONNECT WIRE HARNESS

a.
C402458C01
1,0.146 1.188,0.146 1.188,0.146 2.188,0.375 true 1.656,1.01 1.938,1.01 1.938,1.01 2.323,0.844 true 0.792,0.052 1.01,0.292 0.219,0.24 10 true *a 1.427,0.917 1.646,1.135 0.219,0.219 10 true *b
*a Temperature Sensor Connector
*b Resolver Sensor Connector


Attach the 4 clamps to connect the wire harness to the rear traction motor with transaxle assembly and rear suspension member sub-assembly.


b.

Connect the resolver sensor connector.


c.

Connect the temperature sensor connector.


Hide 51206A 6.INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY

Hide 10.INSPECT FOR HYBRID TRANSAXLE FLUID LEAK

Hide 58441J 12.INSTALL BATTERY SERVICE HOLE COVER

Hide 13.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 65351A 14.INSTALL BATTERY HOLE COVER

Hide 58416K 15.INSTALL REAR NO. 2 FLOOR BOARD

Hide 58410B 16.INSTALL DECK BOARD ASSEMBLY

Hide 17. PERFORM RESOLVER LEARNING

NOTICE:

If the rear traction motor with transaxle assembly has been replaced, make sure to perform resolver learning.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>UTILITY