Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › STEERING PAD › from 2019.02
RM3620E _58 Vehicle Interior _076036 SUPPLEMENTAL RESTRAINT SYSTEMS _0371431 STEERING PAD A

SUPPLEMENTAL RESTRAINT SYSTEMS  STEERING PAD  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 45130 1.INSTALL HORN BUTTON ASSEMBLY

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




c.
B525326C01
2.333,3.083 2.667,2.833 true 2.219,3.063 2.531,3.219 0.313,0.156 10 false *a 2.281,0.688 2.49,0.854 0.208,0.167 10 true *b
*a Lock Button
*b Wire Harness Clamp
V100135

Airbag Connector
V100136

Horn Connector
V113147

Push


for Dual Type:

i.

Support the horn button assembly with one hand.


ii.

Connect the horn connector and attach the wire harness clamp.


iii.

Connect the 2 airbag connectors and push the lock button.

NOTICE:
·

When connecting any airbag connector, take care not to damage the airbag wire harness.

·

Be sure to connect the connectors to each corresponding color.

·

Make sure the lock button is securely locked.




iv.

Set the horn button assembly to the steering wheel assembly.


v.

Check that the airbag wire harness and horn wire harness are not pinched.



d.
B525325C01
2.073,2.948 2.427,2.635 true 1.948,2.927 2.26,3.083 0.313,0.156 10 false *a 2.281,0.688 2.49,0.854 0.208,0.167 10 true *b
*a Lock Button
*b Wire Harness Clamp
V100135

Airbag Connector
V100136

Horn Connector
V113147

Push


for Single Type:

i.

Support the horn button assembly with one hand.


ii.

Connect the horn connector and attach the wire harness clamp.


iii.

Connect the airbag connector and push the lock button.

NOTICE:
·

When connecting any airbag connector, take care not to damage the airbag wire harness.

·

Make sure the lock button is securely locked.




iv.

Set the horn button assembly to the steering wheel assembly.


v.

Check that the airbag wire harness and horn wire harness are not pinched.



e.
B525327C01
0.927,1.073 2.427,1.677 1.5,0.604 0.958,1.104 1.167,1.292 0.208,0.188 10 true *a 1.688,2.281 1.896,2.469 0.208,0.188 10 true *b
*a Upper Pin
*b Lower Pin


Press the horn button assembly with both hands to attach the upper pin to the upper spring.


f.

Press the horn button assembly with both hands to attach the lower pin to the lower spring.

NOTICE:

After installation, try to pull the horn button assembly and check that the horn button assembly is securely installed.



Hide 2.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 65351A 3.INSTALL BATTERY HOLE COVER (for HV Model)

Hide 58416K 4.INSTALL REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 58410B 5.INSTALL DECK BOARD ASSEMBLY (for HV Model)

Hide 45130 6.INSPECT HORN BUTTON ASSEMBLY

a.

Make sure that the horn sounds.

If the horn does not sound, inspect the horn system.

Click hereVehicle Exterior>HORN>HORN SYSTEM>PROBLEM SYMPTOMS TABLE


Hide 9.PERFORM SYSTEM INITIALIZATION AND CALIBRATION