Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2019.02
RM3620E _58 Vehicle Interior _076051 METER / GAUGE / DISPLAY _0374621 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Engine Oil Level Sensor Circuit  


DESCRIPTION

The combination meter assembly and engine oil level sensor are connected via direct line. The combination meter assembly determines the engine oil level based on the engine oil level sensor signal.

HINT:

As the engine oil level may be unstable when the engine is cold or running at high speeds, the combination meter assembly receives the engine coolant temperature signal and engine speed signal from the ECM via CAN communication in order to prevent the oil level warnings from being output erroneously.


WIRING DIAGRAM

E399085E05
2.156,1.344 4.604,1.542 2.448,0.198 10 false ECM 2.615,2.854 4.604,3.052 1.99,0.198 10 false Engine Oil Level Sensor 2.615,2.698 3.073,2.896 0.458,0.198 10 false C20 4.833,3.094 5.146,3.292 0.313,0.198 10 false G19 4.833,3.25 7.125,3.448 2.292,0.198 10 false Combination Meter Assembly 4.958,2.271 5.573,2.469 0.615,0.198 10 false OILW 4.667,2.271 4.979,2.469 0.313,0.198 10 false 31 5.656,1.938 6.271,2.135 0.615,0.198 10 false 12 V 3.49,2.292 3.802,2.49 0.313,0.198 10 false 1 0.563,3.448 2.802,3.688 2.24,0.24 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

The following troubleshooting procedure is based on the assumption that the SFI system is normal. Confirm that the SFI system is not malfunctioning before performing the following procedure.

for A25A-FKS with Canister Pump Module:

Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>HOW TO PROCEED WITH TROUBLESHOOTING

for A25A-FKS without Canister Pump Module:

Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>HOW TO PROCEED WITH TROUBLESHOOTING

for M20A-FKS:

Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

for A25A-FXS with Canister Pump Module:

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>HOW TO PROCEED WITH TROUBLESHOOTING

for A25A-FXS without Canister Pump Module:

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>HOW TO PROCEED WITH TROUBLESHOOTING

for A25B-FXS:

Click hereEngine / Hybrid System>A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ENGINE OIL LEVEL SENSOR)
a.

Disconnect the G19 combination meter assembly connector.


b.

Disconnect the C20 engine oil level sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G19-31 (OILW) - C20-1 Always Below 1 Ω
G19-31 (OILW) or C20-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR