Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY › 2019.02–2020.08
RM3620E _55 Steering _076852 STEERING COLUMN _0377454 STEERING COLUMN ASSEMBLY A

STEERING COLUMN  STEERING COLUMN ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during steering column assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
Steering sensor (Including removal and installation) Steering angle setting Parking assist monitor system (Click here)
Adjust steering angle Panoramic view monitor system (for HV model) (Click here)
Steering angle neutral point Parking assist monitor system (Click here)
Parking support brake system (for HV model) (Click here)
Panoramic view monitor system (for HV model) (Click here)

CAUTION / NOTICE / HINT

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system for A25A-FKS:(Click here)
for M20A-FKS:(Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
Steering sensor (Including removal and installation) Steering angle setting Parking assist monitor system (Click here)
Adjust steering angle Panoramic view monitor system (for Gasoline model) (Click here)
Steering angle neutral point Parking assist monitor system (Click here)
Parking support brake system (for Gasoline model) (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B475753

Be sure to read precaution thoroughly before servicing.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.


Hide 2.PLACE FRONT WHEELS FACING STRAIGHT AHEAD

Hide 58410B 3.REMOVE DECK BOARD ASSEMBLY (for HV Model)

Hide 58416K 4.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 65351A 5.REMOVE BATTERY HOLE COVER (for HV Model)

Hide 6.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


CAUTION:
·
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 67914B 7.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 62112 8.REMOVE COWL SIDE TRIM BOARD LH

Hide 55606 9.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 55474B 10.REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH

Hide 55480D 12.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

Hide 73900 13.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 45100 14.REMOVE STEERING WHEEL ASSEMBLY

Hide 55410C 15.REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

Hide 45287 16.REMOVE STEERING COLUMN LOWER COVER

a.
C406848

Remove the 3 screws.


b.
C406850C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


While pressing the push area shown in the illustration to detach the 2 claws, slightly lower the lower steering column cover sub-assembly.


Hide 45286B 17.REMOVE STEERING COLUMN UPPER COVER

C406852C01
0,0 0,0 false
V113147

Remove in this Direction


a.

Detach the claw and separate the upper steering column cover.


b.
C406854

Detach the 2 claws and 4 clips to remove the upper steering column cover.


Hide 18.REMOVE COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

Do not replace the spiral cable with sensor sub-assembly with the battery connected and the ignition switch ON.

·

Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the battery connected and the ignition switch ON.

·

Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.



a.

Disconnect each connector from the turn signal switch assembly with spiral cable sub-assembly.


b.
C406856

Using pliers, support the band clamp while loosened.


c.
C406858

Detach the claw to remove the turn signal switch assembly with spiral cable sub-assembly from the steering column assembly.


Hide 87211A 19.REMOVE NO. 2 AIR DUCT (for LHD)

a.
C406862C01
1.729,0.198 1.99,0.406 0.26,0.208 10 false *a
*a View A
V100137

Front


Remove the 2 bolts.


b.

Detach the 3 claws to remove the No. 2 air duct.

NOTICE:

Be careful not to deform or damage the lower heater case of the air conditioner unit assembly when removing the No. 2 air duct.



Hide 87211A 20.REMOVE NO. 2 AIR DUCT (for RHD)

a.
C406863C01
2.5,0.198 2.813,0.396 0.313,0.198 10 false *a
*a View A
V100137

Front


Remove the 2 bolts.


b.

Detach the 3 claws to remove the No. 2 air duct.

NOTICE:

Be careful not to deform or damage the lower heater case of the air conditioner unit assembly when removing the No. 2 air duct.



Hide 21.REMOVE FRONT WHEEL LH (for LHD)

Hide 22.REMOVE FRONT WHEEL RH (for RHD)

Hide 45220 23.DISCONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45253 24.REMOVE STEERING COLUMN HOLE COVER

a.

Turn back the floor carpet.


b.
C406864

Remove the clip.


c.

Detach the 2 clips to remove the steering column hole cover.


Hide 45220 25.REMOVE STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C406866

Using a screwdriver, loosen the clamp as shown in the illustration.


b.
C406868C01
1.625,0.594 0.885,0.333 0.885,0.333 1.625,0.51 true 0.552,0.24 0.854,0.448 0.302,0.208 10 true *a
*a Matchmark


Remove the bolt and slide the steering intermediate shaft assembly.

NOTICE:

Do not remove the steering intermediate shaft assembly from the steering column assembly.



c.

Put matchmarks on the steering intermediate shaft assembly and steering column assembly.


d.

Remove the steering intermediate shaft assembly from the steering column assembly.


Hide 45250 26.REMOVE STEERING COLUMN ASSEMBLY

a.

Disconnect each connector and disengage each wire harness clamp from the steering column assembly.


b.
C406870

Remove the bolt, 2 nuts and steering column assembly.