Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT (for A25B-FXS) › 2019.02–2020.08
RM3620E _58 Vehicle Interior _076130 HEATING / AIR CONDITIONING _0388773 AIR CONDITIONING UNIT(for A25B-FXS) A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT(for A25B-FXS)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the air conditioning unit assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
Steering sensor (Including removal and installation) Steering angle setting Parking assist monitor system (Click here)
Adjust steering angle Panoramic view monitor system (for HV model) (Click here)
Steering angle neutral point Parking assist monitor system (Click here)
Parking support brake system (for HV model) (Click here)
Panoramic view monitor system (for HV model) (Click here)

CAUTION:
B521791

·

Wear protective gloves. Sharp areas on the parts may injure your hands.

·

There is risk of injury.



CAUTION:
B475753

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/o Occupant Classification System)>PRECAUTION


NOTICE:
·

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

Make sure to select face mode before disconnecting the cable from the negative (-) auxiliary battery terminal.


Hide 2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 3.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 4.DRAIN ENGINE COOLANT (for Engine)

Hide 5.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55752 6.REMOVE COWL VENTILATOR SPLASH SHIELD

HINT:

Remove using the same procedure that is performed when replacement of the cowl ventilator splash shield is necessary.

Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL


Hide 55704B 7.REMOVE COWL VENTILATOR PANEL SUB-ASSEMBLY

a.

Detach the clamp.

E409428C01
0,0 0,0 false
V100135

Bolt
V100136

Nut



b.

Remove the 4 bolts, 4 nuts and cowl ventilator panel sub-assembly.


Hide 88710E 10.DISCONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY

Hide 14.REMOVE FRONT SEAT ASSEMBLY LH

Hide 15.REMOVE FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 16.REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY

Hide 45250 17.REMOVE STEERING COLUMN ASSEMBLY

Hide 18.REMOVE NAVIGATION ECU WITH BRACKET (w/ Dummy Case)

HINT:

Use the same procedure described as for the navigation ECU with bracket.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ECU>REMOVAL


Hide 73233 19.REMOVE OUTER LAP BELT ANCHOR COVER

Hide 67918E 20.REMOVE REAR DOOR SCUFF PLATE LH

Hide 73220 21.REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH

Hide 62414A 22.REMOVE LOWER CENTER PILLAR GARNISH LH

a.

Remove the rear side of the front door opening trim weatherstrip LH so that the lower center pillar garnish LH can be removed.

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR OPENING TRIM WEATHERSTRIP>REMOVAL


b.

Remove the front side of the rear door opening trim weatherstrip LH so that the lower center pillar garnish LH can be removed.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR OPENING TRIM WEATHERSTRIP>REMOVAL


c.

Remove the lower center pillar garnish LH.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 67917C 23.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure described as for the rear door scuff plate LH.


Hide 73210 24.REMOVE FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure described as for the front seat outer belt assembly LH.


Hide 62413A 25.REMOVE LOWER CENTER PILLAR GARNISH RH

HINT:

Use the same procedure described as for the lower center pillar garnish LH.


Hide 78010F 27.REMOVE ACCELERATOR PEDAL ASSEMBLY

Hide 58569D 28.REMOVE FRONT FLOOR CAUTION PLATE COVER

Hide 58510C 29.REMOVE FRONT FLOOR FRONT CARPET ASSEMBLY

a.

Remove the clip.

E405752C01
0,0 0,0 false
V113147

Fold Back
V100155

Fastener



b.

Detach the guide.


c.

Detach each fastener and fold back the front floor front carpet assembly as shown in the illustration.


d.

Remove the clip.

E405753C01
0,0 0,0 false
V113147

Fold Back - -



e.

Detach the guide and fold back the front floor front carpet assembly as shown in the illustration.


Hide 55215D 30.REMOVE NO. 3 DASH PANEL INSULATOR PAD

Hide 87212F 33.REMOVE REAR NO. 2 AIR DUCT

HINT:

Use the same procedure described as for the rear No. 4 air duct.


Hide 87212 34.REMOVE REAR NO. 1 AIR DUCT

HINT:

Use the same procedure described as for the rear No. 3 air duct.


Hide 55085 36.REMOVE NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY

Hide 55308B 37.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY

Hide 38.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU

Hide 39.DISCONNECT INSTRUMENT PANEL WIRE

a.
E405761C01
1.594,1.365 1.76,1.552 0.167,0.188 10 true *a 2.177,1.063 2.344,1.25 0.167,0.188 10 true *b
*a Clamp
*b Guide


Disconnect the 2 connectors.


b.

Detach the clamp and guide.


c.

Remove the 3 bolts.

E405762C01
1.927,3.49 2.26,3.49 true 2.094,3.646 2.427,3.646 true 2.135,4.948 2.313,5.135 0.177,0.188 10 true *a 2.135,1.656 2.313,1.844 0.177,0.188 10 true *a 1.75,3.385 1.927,3.573 0.177,0.188 10 true *a 2.771,2.51 2.948,2.698 0.177,0.188 10 true *a 3.208,2.76 3.385,2.948 0.177,0.188 10 true *a 4.458,1.094 4.635,1.281 0.177,0.188 10 true *a 1.865,4.865 2.042,5.052 0.177,0.188 10 true *b 1.927,3.552 2.104,3.74 0.177,0.188 10 true *b 4.917,4.344 5.094,4.531 0.177,0.188 10 true *b
*a Clamp *b Guide



d.

Detach the guide and disconnect the 3 ground wires.


e.

Detach the clamp.


f.

Remove the nut.

E410040C01
1.26,2.24 1.427,2.427 0.167,0.188 10 true *a 3.438,1.729 3.604,1.917 0.167,0.188 10 true *a 3.615,2.719 3.781,2.906 0.167,0.188 10 true *a 3.813,2.167 3.979,2.354 0.167,0.188 10 true *b 4.292,3.354 4.458,3.542 0.167,0.188 10 true *a 4.313,4.26 4.479,4.448 0.167,0.188 10 true *a 4.344,4.875 4.51,5.063 0.167,0.188 10 true *a
*a Clamp *b Guide
V100135

Bolt
V100136

Nut
V100137

Connector
V100138

Lever Connector



g.

Remove the bolt.


h.

Detach the guide and disconnect the ground wire.


i.

Disconnect the connector.


j.

Detach the clamp.



Hide 82877 40.REMOVE ECU INTEGRATION BOX RH

Hide 41.DISCONNECT INSTRUMENT PANEL WIRE

a.

Remove the 2 bolts.

E405766C01
3.042,5.979 3.208,6.167 0.167,0.188 10 true *a 3.979,4.094 4.146,4.281 0.167,0.188 10 true *a 1.448,4.323 1.615,4.51 0.167,0.188 10 true *a 1.354,5.396 1.521,5.583 0.167,0.188 10 true *a 4.208,1.073 4.375,1.26 0.167,0.188 10 true *a 2.729,0.729 2.896,0.917 0.167,0.188 10 true *a 3.01,0.833 3.177,1.021 0.167,0.188 10 true *a 5.365,1.823 5.531,2.01 0.167,0.188 10 true *a 4.115,3.042 4.281,3.229 0.167,0.188 10 true *a 5.031,3.292 5.198,3.479 0.167,0.188 10 true *a 5.135,4.656 5.302,4.844 0.167,0.188 10 true *a 2.323,0.354 2.49,0.542 0.167,0.188 10 true *a 1.677,0.396 1.844,0.583 0.167,0.188 10 true *b 5.042,5.604 5.208,5.792 0.167,0.188 10 true *b
*a Clamp *b Guide
V100135

Bolt
V100136

Connector



b.

Detach the guide and disconnect the 2 ground wires.


c.

Disconnect the connector.


d.

Detach the clamp.


Hide 55306A 42.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

Hide 55307C 43.REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

Hide 45.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT ASSEMBLY

Hide 88650N 46.REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY

Hide 47.DISCONNECT INSTRUMENT PANEL WIRE

a.

Disconnect the connector.

E405775


b.

Detach the clamp.


Hide 88539G 50.REMOVE COOLER UNIT DRAIN HOSE GROMMET