Home › Engine / Hybrid System › M20A-FKS (ENGINE CONTROL) › SFI SYSTEM › from 2019.09
RM3620E _51 Engine / Hybrid System _076384 M20A-FKS ENGINE CONTROL _0372800 SFI SYSTEM J

M20A-FKS ENGINE CONTROL  SFI SYSTEM  Starter Signal Circuit  


DESCRIPTION

While the engine is being cranked, current flows from terminal ST1 of the ignition switch assembly*1 or terminal STAR of the certification ECU (smart key ECU assembly)*2 to the park/neutral position switch assembly*3 or clutch start switch assembly*4 and to terminal STA of the ECM (STA signal).

*1: w/o Entry and Start System

*2: w/ Entry and Start System

*3: for Continuously Variable Transaxle Models

*4: for Manual Transaxle Models

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK IF VEHICLE IS EQUIPPED WITH STOP AND START SYSTEM
a.

Confirm the vehicle specifications.

Result:
Result Proceed to
w/ Stop and Start System A
w/o Stop and Start System B




A

2.CHECK WHETHER ENGINE CAN BE CRANKED

B

30.CHECK WHETHER ENGINE CAN BE CRANKED
2.CHECK WHETHER ENGINE CAN BE CRANKED
a.

Check if the engine can be cranked.

Result:
Result Proceed to
Engine cannot be cranked A
Engine can be cranked B




A

3.READ VALUE USING GTS (STARTER SW)

B

29.READ VALUE USING GTS (STARTER SW)
3.READ VALUE USING GTS (STARTER SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Starter SW.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11

e.

Fully depress the clutch pedal (for Manual Transaxle Models with Clutch Start System).


f.

Check the value displayed on the GTS when the ignition switch is turned to ON and START positions.

OK:
Condition GTS Display (Starter SW)
Ignition switch ON OFF
Engine started ON



Result:
Result Proceed to
NG A
OK (for Continuously Variable Transaxle Models) B
OK (for Manual Transaxle Models) C



A

4.CHECK STOP AND START SYSTEM

B

18.INSPECT ST NO. 1 RELAY

C

44.INSPECT ST NO. 1 RELAY
4.CHECK STOP AND START SYSTEM

Result:
Result Proceed to
OK (for Continuously Variable Transaxle Models) A
OK (for Manual Transaxle Models) B
NG C



A

5.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ECM - ST NO. 2 RELAY)

B

12.INSPECT CLUTCH START SWITCH ASSEMBLY

C

REPAIR STOP AND START SYSTEM

5.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ECM - ST NO. 2 RELAY)
a.

Disconnect the engine stop and start ECU connector.


b.

Disconnect the ECM connector.


c.

Remove the ST NO. 2 relay from the No. 1 engine room relay block and junction block assembly.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A34-23 (STA2) - A24-30 (STA) Always Below 1 Ω
A34-23 (STA2), A24-30 (STA) or 2 (ST NO. 2 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

Result:
Result Proceed to
OK (w/ Entry and Start System) A
OK (w/o Entry and Start System) B
NG C



A

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ENGINE STOP AND START ECU - ST NO. 1 RELAY - CERTIFICATION ECU)

B

9.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ENGINE STOP AND START ECU - ST NO. 1 RELAY)

C

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ENGINE STOP AND START ECU - ST NO. 1 RELAY - CERTIFICATION ECU)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Disconnect the engine stop and start ECU connector.


c.

Disconnect the TCM connector.


d.

Remove the ST NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


e.

Disconnect the certification ECU (smart key ECU assembly) connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C31-5 (L) - A34-21 (STA) Always Below 1 Ω
C31-5 (L) - A15-20 (STA) Always Below 1 Ω
C31-5 (L), A34-21 (STA), 2 (ST NO. 1 relay), C33-28 (STA) or A15-20 (STA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM - ENGINE STOP AND START ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM - ENGINE STOP AND START ECU)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Disconnect the ECM connector.


d.

Disconnect the engine stop and start ECU connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A15-9 (STAR) - C31-4 (B) Always Below 1 Ω
A15-9 (STAR) - A24-23 (NSW) Always Below 1 Ω
A15-9 (STAR) - A34-17 (CLL) Always Below 1 Ω
A15-9 (STAR), C31-4 (B), A24-23 (NSW) or A34-17 (CLL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ENGINE STOP AND START ECU - ST NO. 1 RELAY)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Disconnect the engine stop and start ECU connector.


c.

Disconnect the TCM connector.


d.

Remove the ST NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C31-5 (L) - A34-21 (STA) Always Below 1 Ω
C31-5 (L), A34-21 (STA), C33-28 (STA) or 2 (ST NO. 1 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM - ENGINE STOP AND START ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM - ENGINE STOP AND START ECU)
a.

Disconnect the ignition switch assembly connector.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Disconnect the ECM connector.


d.

Disconnect the engine stop and start ECU connector.


e.

Disconnect the TCM connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G28-5 (ST1) - C31-4 (B) Always Below 1 Ω
G28-5 (ST1) - A24-23 (NSW) Always Below 1 Ω
G28-5 (ST1) - A34-17 (CLL) Always Below 1 Ω
G28-5 (ST1), C31-4 (B), A24-23 (NSW) or A34-17 (CLL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>M20A-FKS (STARTING)>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH ASSEMBLY)

NG

REPLACE IGNITION SWITCH ASSEMBLY

12.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Inspect the clutch start switch assembly.

for LHD: Click hereDrivetrain>CLUTCH>CLUTCH START SWITCH (for LHD)>INSPECTION

for RHD: Click hereDrivetrain>CLUTCH>CLUTCH START SWITCH (for RHD)>INSPECTION


Result:
Result Proceed to
OK (w/ Entry and Start System) A
OK (w/o Entry and Start System) B
NG C



A

13.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ECM - ST NO. 1 RELAY - CERTIFICATION ECU)

B

15.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ECM - ST NO. 1 RELAY)

C

REPLACE CLUTCH START SWITCH ASSEMBLY

13.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ECM - ST NO. 1 RELAY - CERTIFICATION ECU)
a.

Disconnect the engine stop and start ECU connector.


b.

Disconnect the ECM connector.


c.

Remove the ST NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


d.

Disconnect the clutch start switch assembly connector.


e.

Disconnect the certification ECU (smart key ECU assembly) connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A34-21 (STA) - A24-30 (STA) Always Below 1 Ω
A34-21 (STA) - A81-1 Always Below 1 Ω
A34-21 (STA), A24-30 (STA), A15-20 (STA), A81-1 or 2 (ST NO. 1 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - CLUTCH START SWITCH ASSEMBLY - ENGINE STOP AND START ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - CLUTCH START SWITCH ASSEMBLY - ENGINE STOP AND START ECU)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Disconnect the clutch start switch assembly connector.


c.

Disconnect the engine stop and start ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A15-9 (STAR) - A81-2 Always Below 1 Ω
A15-9 (STAR) - A34-17 (CLL) Always Below 1 Ω
A15-9 (STAR), A81-2 or A34-17 (CLL) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ECM - ST NO. 1 RELAY)
a.

Disconnect the engine stop and start ECU connector.


b.

Disconnect the ECM connector.


c.

Remove the ST NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


d.

Disconnect the clutch start switch assembly connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A34-21 (STA) - A24-30 (STA) Always Below 1 Ω
A34-21 (STA) - A81-1 Always Below 1 Ω
A34-21 (STA), A24-30 (STA), A81-1 or 2 (ST NO. 1 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY)
a.

Disconnect the ignition switch assembly connector.


b.

Disconnect the clutch start switch assembly connector.


c.

Disconnect the engine stop and start ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G28-5 (ST1) - A81-2 Always Below 1 Ω
G28-5 (ST1) - A34-17 (CLL) Always Below 1 Ω
G28-5 (ST1), A34-17 (CLL) or A81-2 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

17.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>M20A-FKS (STARTING)>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH ASSEMBLY)

NG

REPLACE IGNITION SWITCH ASSEMBLY

18.INSPECT ST NO. 1 RELAY
a.

Inspect the ST NO. 1 relay.

Click hereEngine / Hybrid System>M20A-FKS (STARTING)>RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

19.INSPECT ST NO. 2 RELAY

NG

REPLACE ST NO. 1 RELAY

19.INSPECT ST NO. 2 RELAY
a.

Inspect the ST NO. 2 relay.

Click hereEngine / Hybrid System>M20A-FKS (STARTING)>RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

20.INSPECT STARTER ASSEMBLY

NG

REPLACE ST NO. 2 RELAY

20.INSPECT STARTER ASSEMBLY

OK

21.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - STARTER ASSEMBLY)

NG

21.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - STARTER ASSEMBLY)
a.

Remove the ST NO. 2 relay from No. 1 engine room relay block and junction block assembly.


b.

Disconnect the starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (ST NO. 2 relay holder) - C43-1 (SL2) Always Below 1 Ω
3 (ST NO. 2 relay holder) or C43-1 (SL2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

22.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - ECM)
a.

Remove the ST NO. 2 relay from the No. 1 engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (ST NO. 2 relay) - A24-30 (STA) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

23.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - BODY GROUND)
a.

Remove the ST NO. 2 relay from the No. 1 engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (ST NO. 2 relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

24.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

24.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST NO. 2 RELAY)
A435793C01
0.094,0.063 0.406,0.219 0.313,0.156 10 false *1 2.188,0.958 2.5,1.115 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*2 ST NO. 2 Relay


a.

Remove the ST NO. 2 relay from the No. 1 engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (ST NO. 2 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

25.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ST NO. 2 RELAY)

25.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)
a.

Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.


b.

Disconnect the starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (ST NO. 1 relay) - C43-2 (SL1) Always Below 1 Ω
3 (ST NO. 1 relay) or C43-2 (SL1) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

26.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

26.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)
a.

Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (ST NO. 1 relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

27.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

27.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST NO. 1 RELAY)
A435792C01
0.094,0.063 0.406,0.219 0.313,0.156 10 false *1 2.125,1.188 2.438,1.344 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*2 ST NO. 1 Relay


a.

Remove the ST NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (ST NO. 1 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

28.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ST NO 1 RELAY)

28.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST NO. 1 RELAY)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C31-5 (L) - 2 (ST NO. 1 relay) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

29.READ VALUE USING GTS (STARTER SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Starter SW.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11

e.

Fully depress the clutch pedal (for Manual Transaxle Models with Clutch Start System).


f.

Check the value displayed on the GTS when the ignition switch is turned to ON and START positions.

OK:
Condition GTS Display (Starter SW)
Ignition switch ON OFF
Engine started ON



Result:
Result Proceed to
OK A
NG (for Continuously Variable Transaxle Models) B
NG (for Manual Transaxle Models) C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST NO. 2 RELAY - ECM)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST NO. 1 RELAY - ECM)

30.CHECK WHETHER ENGINE CAN BE CRANKED
a.

Check if the engine can be cranked.

Result:
Result Proceed to
Engine cannot be cranked A
Engine can be cranked B




A

31.READ VALUE USING GTS (STARTER SW)

B

52.READ VALUE USING GTS (STARTER SW)
31.READ VALUE USING GTS (STARTER SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Starter SW.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11

e.

Fully depress the clutch pedal (for Manual Transaxle Models with Clutch Start System).


f.

Check the value displayed on the GTS when the ignition switch is turned to ON and START positions.

OK:
Condition GTS Display (Starter SW)
Ignition switch ON OFF
Engine started ON



Result:
Result Proceed to
NG (for Continuously Variable Transaxle Models) A
NG (for Manual Transaxle Models) B
OK C



A

32.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

B

38.INSPECT CLUTCH START SWITCH ASSEMBLY

C

44.INSPECT ST NO. 1 RELAY
32.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

Result:
Result Proceed to
OK (w/ Entry and Start System) A
OK (w/o Entry and Start System) B
NG C



A

33.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)

B

35.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)

C

33.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.


c.

Disconnect the ECM connector.


d.

Disconnect the TCM connector.


e.

Disconnect the certification ECU (smart key ECU assembly) connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C31-5 (L) - 2 (ST NO. 1 relay) Always Below 1 Ω
A24-30 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
A15-20 (STA), 2 (ST NO. 1 relay), C31-5 (L), A24-30 (STA) or C33-28 (STA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

34.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

34.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A15-9 (STAR) - C31-4 (B) Always Below 1 Ω
A15-9 (STAR) - A24-23 (NSW) Always Below 1 Ω
A15-9 (STAR), C31-4 (B) or A24-23 (NSW) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

35.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.


c.

Disconnect the ECM connector.


d.

Disconnect the TCM connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C31-5 (L) - 2 (ST NO. 1 relay) Always Below 1 Ω
A24-30 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
C31-5 (L), 2 (ST NO. 1 relay), A24-30 (STA) or C33-28 (STA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

36.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

36.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
a.

Disconnect the ignition switch assembly connector.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G28-5 (ST1) - C31-4 (B) Always Below 1 Ω
G28-5 (ST1) - A24-23 (NSW) Always Below 1 Ω
G28-5 (ST1), C31-4 (B) or A24-23 (NSW) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

37.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

37.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>M20A-FKS (STARTING)>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH ASSEMBLY)

NG

REPLACE IGNITION SWITCH ASSEMBLY

38.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Inspect the clutch start switch assembly.

for LHD: Click hereDrivetrain>CLUTCH>CLUTCH START SWITCH (for LHD)>INSPECTION

for RHD: Click hereDrivetrain>CLUTCH>CLUTCH START SWITCH (for RHD)>INSPECTION


Result:
Result Proceed to
OK (w/ Entry and Start System) A
OK (w/o Entry and Start System) B
NG C



A

39.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)

B

41.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)

C

REPLACE CLUTCH START SWITCH ASSEMBLY

39.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)
a.

Disconnect the clutch start switch assembly connector.


b.

Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.


c.

Disconnect the ECM connector.


d.

Disconnect the certification ECU (smart key ECU assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A81-1 - 2 (ST NO. 1 relay) Always Below 1 Ω
A24-30 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
A15-20 (STA), 2 (ST NO. 1 relay), A81-1 or A24-30 (STA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

40.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - CLUTCH START SWITCH ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

40.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - CLUTCH START SWITCH ASSEMBLY - ECM)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Disconnect the clutch start switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A15-9 (STAR) - A81-2 Always Below 1 Ω
A15-9 (STAR) or A81-2 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

41.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)
a.

Disconnect the clutch start switch assembly connector.


b.

Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A81-1 - 2 (ST NO. 1 relay) Always Below 1 Ω
A24-30 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
A81-1, 2 (ST NO. 1 relay) or A24-30 (STA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

42.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

42.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY)
a.

Disconnect the ignition switch assembly connector.


b.

Disconnect the clutch start switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G28-5 (ST1) - A81-2 Always Below 1 Ω
G4-5 (ST1) or A81-2 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

43.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

43.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>M20A-FKS (STARTING)>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH ASSEMBLY)

NG

REPLACE IGNITION SWITCH ASSEMBLY

44.INSPECT ST NO. 1 RELAY
a.

Inspect the ST NO. 1 relay.

Click hereEngine / Hybrid System>M20A-FKS (STARTING)>RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

45.INSPECT STARTER ASSEMBLY

NG

REPLACE ST NO. 1 RELAY

45.INSPECT STARTER ASSEMBLY

OK

46.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)

NG

46.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)
a.

Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.


b.

Disconnect the starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Stop and Start System
Tester Connection Condition Specified Condition
3 (ST NO. 1 relay) - C43-2 (SL1) Always Below 1 Ω
3 (ST NO. 1 relay) or C43-2 (SL1) - Body ground and other terminals Always 10 kΩ or higher

w/o Stop and Start System
Tester Connection Condition Specified Condition
3 (ST NO. 1 relay) - C42-1 (ST) Always Below 1 Ω
3 (ST NO. 1 relay) or C42-1 (ST) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

47.CHECK TERMINAL VOLTAGE (BATTERY - STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

47.CHECK TERMINAL VOLTAGE (BATTERY - STARTER ASSEMBLY)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the cable from the positive (+) battery terminal.


c.

Disconnect the starter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Stop and Start System
Tester Connection Condition Specified Condition
Positive (+) battery terminal - D1-1 (B) Always Below 1 Ω

w/o Stop and Start System
Tester Connection Condition Specified Condition
Positive (+) battery terminal - D2-1 (B) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

48.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

48.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST NO. 1 RELAY)
A435792C01
0.094,0.063 0.406,0.219 0.313,0.156 10 false *1 2.125,1.188 2.438,1.344 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*2 ST NO. 1 Relay


a.

Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (ST NO. 1 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

49.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ST NO. 1 RELAY)

49.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)
a.

Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (ST NO. 1 relay) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (for Continuously Variable Transaxle Models) A
OK (for Manual Transaxle Models) B
NG C



A

50.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

B

51.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - CLUTCH START SWITCH ASSEMBLY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

50.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Remove the ST NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (ST NO. 1 relay) - C31-5 (L) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

51.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - CLUTCH START SWITCH ASSEMBLY)
a.

Remove the ST NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


b.

Disconnect the clutch start switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (ST NO. 1 relay) - A81-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

52.READ VALUE USING GTS (STARTER SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Starter SW.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11

e.

Fully depress the clutch pedal (for Manual Transaxle Models with Clutch Start System).


f.

Check the value displayed on the GTS when the ignition switch is turned to ON and START positions.

OK:
Condition GTS Display (Starter SW)
Ignition switch ON OFF
Engine started ON



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST NO. 1 RELAY - ECM)