Home › Drivetrain › Q610 (HYBRID TRANSMISSION / TRANSAXLE) › HYBRID TRANSAXLE SIDE GEAR OIL SEAL › from 2019.09
RM3620E _52 Drivetrain _080124 Q610 HYBRID TRANSMISSION / TRANSAXLE _0388723 HYBRID TRANSAXLE SIDE GEAR OIL SEAL A

Q610 HYBRID TRANSMISSION / TRANSAXLE  HYBRID TRANSAXLE SIDE GEAR OIL SEAL  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear drive shaft oil seal LH or rear drive shaft oil seal RH removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Rear wheel alignment adjustment
·

Clear zero point calibration data.

·

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (for HV model) (Click here)
Television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (for HV model) (Click here)
Perform headlight ECU sub-assembly LH initialization Lighting System (EXT) (Click here)

NOTICE:

For the hybrid transaxle fluid, use Toyota Genuine ATF WS.

Using transmission fluid other than the above type may cause abnormal noise or vibration, or ultimately damage the transmission of your vehicle.


PROCEDURE

Hide 58398F 1.REMOVE NO. 1 FLOOR UNDER COVER (w/ No. 1 Floor Under Cover)

Hide 42340D 4.REMOVE REAR DRIVE SHAFT OIL SEAL LH

a.
C407238N01
0.896,1.292 1.073,0.51 1.073,0.51 1.208,0.51 true 1.25,0.427 1.646,0.667 0.396,0.24 10 true SST

Using SST, remove the rear drive shaft oil seal LH from the rear traction motor with transaxle assembly.

SST
09308-00010  

NOTICE:

Be careful not to damage the rear traction motor with transaxle assembly.



Hide 42330G 5.REMOVE REAR DRIVE SHAFT OIL SEAL RH

a.
C407254C01
1.583,2.667 1.76,3.146 1.76,3.146 1.979,3.146 true 2.021,3.052 2.396,3.271 0.375,0.219 10 true SST 0.833,3.063 1.115,3.302 0.281,0.24 10 true *a
*a Hold
V113147

Turn


Using SST, remove the rear drive shaft oil seal RH from the rear traction motor with transaxle assembly.

SST
09612-65014  (09612-01020)

NOTICE:

Be careful not to damage the rear traction motor with transaxle assembly.



Hide 42330G 6.INSTALL REAR DRIVE SHAFT OIL SEAL RH

a.

Apply MP grease to the lip of a new rear drive shaft oil seal RH.


b.
C407252C01
2.635,1.063 2.635,0.938 2.635,0.938 2.594,0.823 false 2.365,1.073 2.365,0.885 2.365,0.885 2.417,0.75 false 0.948,2.708 0.948,2.302 0.948,2.302 1.115,2.021 true 2,2.823 2.219,3.083 2.219,3.083 2.365,3.083 true 2.719,0.115 2.969,0.354 0.25,0.24 10 false *a 2.552,1.073 2.74,1.281 0.188,0.208 10 false *b 2.281,1.063 2.5,1.281 0.219,0.219 10 false *c 0.813,2.729 1.135,2.958 0.323,0.229 10 true SST 2.406,3 2.74,3.219 0.333,0.219 10 true SST
*a Depth
*b Inner Lip
*c Outer Lip


Using SST and a hammer, install the rear drive shaft oil seal RH to the rear traction motor with transaxle assembly.

SST
09316-20011  
09517-30010  

Standard Depth:

-0.5 to 0.5 mm (-0.0196 to 0.0196 in.)


NOTICE:
C381409C01
2.292,1.073 2.427,1.073 2.427,1.073 2.427,1.406 false 1.323,1.26 1.552,1.26 false 2.219,0.75 2.583,0.75 false 0.729,0.75 1.094,0.75 false 1.052,0.281 1.333,0.51 0.281,0.229 10 false *a 2.542,0.281 2.823,0.51 0.281,0.229 10 false *b 2.125,0.979 2.406,1.208 0.281,0.229 10 false *c 1.594,1.156 1.875,1.385 0.281,0.229 10 false *c 0.427,0.677 0.885,0.875 0.458,0.198 10 false SST 1.917,0.677 2.375,0.875 0.458,0.198 10 false SST
*a Correct
*b Incorrect
*c Outer Lip


·

Make sure that the outer lip of the rear drive shaft oil seal RH is not pinched by SST.

·

Do not allow foreign matter to attach to the inner lip and outer lip of the rear drive shaft oil seal RH.

·

Do not install the rear drive shaft oil seal RH at an angle.

·

Do not remove the grease from the inner lip and outer lip of the rear drive shaft oil seal RH.




Hide 42340D 7.INSTALL REAR DRIVE SHAFT OIL SEAL LH

a.

Apply MP grease to the lip of a new rear drive shaft oil seal LH.


b.
C407251C01
2.906,2.458 2.906,2.198 2.906,2.198 2.552,1.958 true 1.813,3.01 1.813,2.823 1.813,2.823 2.063,2.656 true 1.073,1.063 1.073,0.896 1.073,0.896 1.031,0.75 false 0.792,1 0.792,0.896 0.792,0.896 0.865,0.802 false 1.667,3.021 2.031,3.25 0.365,0.229 10 true SST 2.76,2.469 3.104,2.688 0.344,0.219 10 true SST 1.156,0.156 1.406,0.375 0.25,0.219 10 false *a 0.719,1 0.938,1.25 0.219,0.25 10 false *b 1,1.052 1.24,1.271 0.24,0.219 10 false *c
*a Depth
*b Inner Lip
*c Outer Lip


Using SST and a hammer, install the rear drive shaft oil seal LH to the rear traction motor with transaxle assembly.

SST
09316-20011  
09517-30010  

Standard Depth:

-0.5 to 0.5 mm (-0.0196 to 0.0196 in.)


NOTICE:
C381409C01
2.292,1.073 2.427,1.073 2.427,1.073 2.427,1.406 false 1.323,1.26 1.552,1.26 false 2.219,0.75 2.583,0.75 false 0.729,0.75 1.094,0.75 false 1.052,0.281 1.333,0.51 0.281,0.229 10 false *a 2.542,0.281 2.823,0.51 0.281,0.229 10 false *b 2.125,0.979 2.406,1.208 0.281,0.229 10 false *c 1.594,1.156 1.875,1.385 0.281,0.229 10 false *c 0.427,0.677 0.885,0.875 0.458,0.198 10 false SST 1.917,0.677 2.375,0.875 0.458,0.198 10 false SST
*a Correct
*b Incorrect
*c Outer Lip


·

Make sure that the outer lip of the rear drive shaft oil seal LH is not pinched by SST.

·

Do not allow foreign matter to attach to the inner lip and outer lip of the rear drive shaft oil seal LH.

·

Do not install the rear drive shaft oil seal LH seal at an angle.

·

Do not remove the grease from the inner lip and outer lip of the rear drive shaft oil seal LH.




Hide 11.INSPECT FOR HYBRID TRANSAXLE FLUID LEAK

Hide 58398F 12.INSTALL NO. 1 FLOOR UNDER COVER (w/ No. 1 Floor Under Cover)