The main body ECU (multiplex network body ECU) controls the operation of the following lights:
Map light assembly
No. 1 room light assembly
Transponder key coil*1
No. 1 interior illumination light assembly (footwell light)*2
No. 2 interior illumination light assembly (footwell light)*2
No. 3 interior illumination light assembly (center tray light)*3
No. 4 interior illumination light assembly (driver side tray light)*3
No. 5 interior illumination light assembly (front passenger side tray light)*3
No. 6 interior illumination light assembly (cup holder light)*4
*1: w/o Entry and Start System
*2: w/ Footwell Light
*3: w/ Tray Light
*4: w/ Cup Holder Light
Inspect the fuses for circuits related to this system before performing the following procedure.
w/ Entry and Start System:
If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.
Check which interior illumination does not turn on.
| Result | Proceed to |
|---|---|
| Map light assembly, No. 1 room light assembly or transponder key coil (w/o Entry and Start System) does not turn on | A |
| Interior foot illumination (w/ Footwell Light), tray illumination (w/ Tray Light) or cup holder illumination (w/ Cup Holder Light) does not turn on | B |
A
B
Perform the Active Test according to the display on the GTS.
Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Illuminated Entry System | Turns on the lights that are controlled by the illuminated entry system* | OFF or ON | Perform the Active Test with the DOOR switch in the map light assembly, No. 1 room light assembly and transponder key coil (w/o Entry and Start System) turned on. |
| Tester Display |
|---|
| Illuminated Entry System |
*: Refer to Operation Check for the lights that are controlled by the illuminated entry system.
Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>OPERATION CHECK
Map light assembly, No. 1 room light assembly and transponder key coil (w/o Entry and Start System) turn on or off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for TMMR Made
*2: except TMMR Made
*3: w/o Entry and Start System
Disconnect the P14*1 or P20*2 map light assembly connector.
Disconnect the P15 No. 1 room light assembly connector.
Disconnect the G53 transponder key coil connector.*3
Disconnect the 4D instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| P14-1 (CTY) - 4D-29 | Always | Below 1 Ω |
| P14-1 (CTY) or 4D-29 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| P20-1 (CTY) - 4D-29 | Always | Below 1 Ω |
| P20-1 (CTY) or 4D-29 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4D-29 - A-1 (ILE) | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG (for LHD) | C |
| NG (for RHD) | D |
A
B
C
D
Perform the Active Test according to the display on the GTS.
Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Fr Foot Light | Operation of the following lights:
·
No. 1 interior illumination light assembly (footwell light) ·
No. 2 interior illumination light assembly (footwell light) ·
No. 3 interior illumination light assembly (center tray light)*1 ·
No. 4 interior illumination light assembly (driver side tray light)*1 ·
No. 5 interior illumination light assembly (front passenger side tray light)*1 ·
No. 6 interior illumination light assembly (cup holder light)*2 |
OFF or ON | - |
| Tester Display |
|---|
| Fr Foot Light |
*1: w/ Tray Light
*2: w/ Cup Holder Light
Connected light is turn on or off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: w/ Tray Light
*2: w/ Cup Holder Light
Disconnect the G77 No. 1 interior illumination light assembly (footwell light) connector.
Disconnect the G76 No. 2 interior illumination light assembly (footwell light) connector.
Disconnect the G87 No. 3 interior illumination light assembly (center tray light) connector.*1
Disconnect the G86 No. 4 interior illumination light assembly (driver side light) connector.*1
Disconnect the H3 No. 5 interior illumination light assembly (front passenger light) connector.*1
Disconnect the N48 No. 6 interior illumination light assembly (cup holder light) connector.*2
Disconnect the 4A instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4A-37 - G77-1 (L) | Always | Below 1 Ω |
| 4A-37 or G77-1 (L) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4A-37 - A-26 (FSPT) | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG (for LHD) | C |
| NG (for RHD) | D |
A
B
C
D