The operation of the compressor with motor assembly is stopped and this DTC is stored if the rotation load is too large or too small while the compressor with motor assembly is operating.
Possible causes are refrigerant leaks, overcharged refrigerant, insufficient cooling due to a condenser fan circuit malfunction, or compressor lock.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory |
|---|---|---|---|---|
| B1476 | A/C Inverter Load System Malfunction | ·
Diagnosis condition: Compressor operation request ·
Malfunction status: Motor rotation load while the compressor is operating is too large or too small ·
Detection time: None |
·
Refrigerant volume ·
Compressor with motor assembly ·
Cooling fan system ·
CAN communication system |
Memorized |
Wear insulated gloves and pull out the service plug grip before inspection as procedures may require disconnecting high-voltage connectors. Carry the removed service plug in your pocket to prevent other technicians from accidentally reconnecting it while you are servicing the vehicle.
Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
for 2WD with NICKEL METAL HYDRIDE BATTERY:Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>PRECAUTION
for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY:Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>PRECAUTION
for 2WD with LITHIUM-ION BATTERY:Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with LITHIUM-ION BATTERY)>PRECAUTION
for 4WD/AWD with LITHIUM-ION BATTERY:Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with LITHIUM-ION BATTERY)>PRECAUTION
The hybrid control system and air conditioning system output DTCs separately. Perform troubleshooting for the hybrid control system first if DTCs from these systems are output simultaneously.
Using the GTS, check if the CAN communication system is functioning normally.
| Result | Proceed to |
|---|---|
| CAN communication system DTCs are not output | A |
| CAN communication system DTCs are output | B |
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test.
Check the operation by referring to the table below.
| Tester Display | Measurement Item | Control Range | Restrict Condition |
|---|---|---|---|
| Control the Engine Cooling Fan Duty Ratio | Electric cooling fan motor operation | 0 to 100 (%) | Perform this test when vehicle is stopped. |
| Tester Display |
|---|
| Control the Engine Cooling Fan Duty Ratio |
Electric cooling fan operates smoothly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Install a manifold gauge set.
Turn the power switch on (READY).
Read the manifold gauge pressure when the following conditions are met.
Prepare the vehicle according to the table below.
| Item | Condition |
|---|---|
| Vehicle Condition | Power switch on (READY) |
| Doors | Fully closed (windows also fully closed) |
| A/C Switch | On |
| Recirculation/fresh Control Switch | Recirculation |
| Set Temperature | MAX COLD |
| Blower Speed | HI |
| Air Conditioning Air Inlet Temperature | 25 to 35°C (77 to 95°F) |
150 to 250 kPa (1.5 to 2.5 kgf/cm2, 22 to 36 psi)
1370 to 1570 kPa (14 to 16 kgf/cm2, 199 to 228 psi)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for HFO-1234yf (R1234yf):Vehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFO-1234yf(R1234yf))>REPLACEMENT