Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR (for A25A-FXS) › 2020.05–2020.08
RM3620E _58 Vehicle Interior _076130 HEATING / AIR CONDITIONING _0374936 COMPRESSOR(for A25A-FXS) A

HEATING / AIR CONDITIONING  COMPRESSOR(for A25A-FXS)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the compressor with motor assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



NOTICE:
·

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



HINT:
·

Use the same procedure as for the LHD and RHD vehicles.

·

The procedure listed below is for the LHD vehicles.



PROCEDURE

Hide 1.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 4.REMOVE FRONT WHEEL RH

Hide 75601A 5.REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY RH

HINT:

Use the same procedure described as for the LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>WHEEL OPENING MOULDING (for Front)>REMOVAL


Hide 53896B 6.REMOVE FRONT FENDER FRONT SPLASH SHIELD LH

Hide 53895B 7.REMOVE FRONT FENDER FRONT SPLASH SHIELD RH

Hide 51441 8.REMOVE NO. 1 ENGINE UNDER COVER

Hide 76621D 9.REMOVE FRONT FENDER MUDGUARD RH (w/ Mudguard)

HINT:

Use the same procedure described as for the LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>MUDGUARD>REMOVAL


Hide 53736E 10.REMOVE FRONT FENDER APRON SEAL RH

Hide 53875A 11.REMOVE FRONT FENDER LINER RH

Hide 88704 12.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

a.
E408285

Remove the bolt and disconnect the suction hose sub-assembly.

NOTICE:

Do not apply excessive force to the suction hose sub-assembly.



b.

Remove the O-ring from the suction hose sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.



Hide 88711 13.DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

a.
E408286

Remove the bolt and disconnect the No. 1 cooler refrigerant discharge hose.

NOTICE:

Do not apply excessive force to the No. 1 cooler refrigerant discharge hose.



b.

Remove the O-ring from the No. 1 cooler refrigerant discharge hose.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.



Hide 88370 14.REMOVE COMPRESSOR WITH MOTOR ASSEMBLY

a.
E408287C01
0,0 0,0 false
V100135

Connector (A)


Disconnect the connector (A).


b.
E408288

Remove the 2 nuts.


c.
E408289C01
0,0 0,0 false
V100135

Bolt
V100136

Stud Bolt


Using an E8 "TORX" socket wrench, remove the 2 stud bolts and bolt.

NOTICE:

Do not drop or subject the parts to any impact.



d.
E408290C01
0,0 0,0 false
V100135

Connector (B)
V100136

Slide
V100155

Green-colored Lock


Slide the green-colored lock of the connector (B) as shown in the illustration to release it and disconnect the connector.

CAUTION:

Make sure to wear insulated gloves.


NOTICE:

Insulate the disconnected terminals and connector with insulating tape.



e.
E408291

Remove the compressor with motor assembly from the location shown in the illustration.

NOTICE:

Do not damage surrounding parts.