Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for HV Model) › from 2020.05
RM3620E _58 Vehicle Interior _076130 HEATING / AIR CONDITIONING _0370842 AIR CONDITIONING SYSTEM(for HV Model) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for HV Model)  B1498  Communication Malfunction (A/C Inverter Local)  


DESCRIPTION

The hybrid vehicle control ECU assembly and compressor with motor assembly communicate via a direct line. Compressor control is stopped and this DTC is stored if communication information is cut off or abnormal information occurs.

This DTC is also detected if high-voltage power supplied from the inverter with converter assembly to the compressor control circuit is shut off.

This DTC will be stored as a history DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1498 Communication Malfunction (A/C Inverter Local)
·

Diagnosis condition: Power switch on (READY)

·

Malfunction status: Error or open in communication line between the hybrid vehicle control ECU assembly and compressor with motor assembly or high-voltage power source shut off


·

Harness or connector

·

Hybrid vehicle control ECU assembly

·

Compressor with motor assembly

·

HV air conditioning wire

·

CAN communication system

·

Hybrid control system


Memorized

WIRING DIAGRAM

E414323E02
3.51,0.781 4.125,0.979 0.615,0.198 10 false LIN3 3.281,0.615 3.896,0.813 0.615,0.198 10 false 8 2.969,1.229 3.583,1.427 0.615,0.198 10 false A29 2.958,1.406 4.719,1.823 1.76,0.417 10 false Hybrid Vehicle Control ECU Assembly 3.198,2.188 4.781,2.417 1.583,0.229 10 false from IG1 NO.1 Relay 5.5,1.302 7.083,1.698 1.583,0.396 10 false Air Conditioning Amplifier Assembly 1.958,2.344 3.083,2.563 1.125,0.219 10 false ECU-IG1 NO.3 1.542,0.792 2.156,0.99 0.615,0.198 10 false C52 1.625,0.563 2.24,0.76 0.615,0.198 10 false 3 1.552,2.208 2.167,2.406 0.615,0.198 10 false C52 1.615,1.979 2.229,2.177 0.615,0.198 10 false 1 1.552,2.615 2.167,2.813 0.615,0.198 10 false C52 1.625,2.427 2.24,2.625 0.615,0.198 10 false 2 1.604,3.042 2.219,3.24 0.615,0.198 10 false Z1 1.635,2.823 2.25,3.021 0.615,0.198 10 false 2 1.604,3.865 2.219,4.063 0.615,0.198 10 false Z1 1.625,3.656 2.24,3.854 0.615,0.198 10 false 1 1.031,0.802 1.646,1 0.615,0.198 10 false DOUT 1.177,2.198 1.792,2.396 0.615,0.198 10 false IG1 1.104,2.625 1.719,2.823 0.615,0.198 10 false GND 1.219,3.052 1.833,3.25 0.615,0.198 10 false PB 1.313,3.448 1.927,3.646 0.615,0.198 10 false E 1.292,4.26 1.906,4.458 0.615,0.198 10 false E 1.219,3.865 1.833,4.063 0.615,0.198 10 false PE 5.135,3.458 5.75,3.656 0.615,0.198 10 false E 5.135,4.292 5.75,4.49 0.615,0.198 10 false E 5.135,3.719 5.75,3.917 0.615,0.198 10 false ACPE 5.135,2.885 5.75,3.083 0.615,0.198 10 false ACPB 0.313,4.729 1.427,5.115 1.115,0.385 10 false Compressor with Motor Assembly 2.656,4.698 4.354,4.885 1.698,0.188 10 false HV Air Conditioning Wire 4.958,4.885 7.031,5.146 2.073,0.26 10 false Inverter with Converter Assembly 4.969,4.719 6.938,4.979 1.969,0.26 10 false Z2 0.76,5.406 2.99,5.604 2.229,0.198 10 false : CAN Communication Line 0.76,5.865 2.99,6.063 2.229,0.198 10 false : LIN Communication Line 0.771,6.333 3,6.531 2.229,0.198 10 false : High Voltage Line 3.229,3.542 3.844,3.74 0.615,0.198 10 false * 3.25,4.385 3.865,4.583 0.615,0.198 10 false * 2.792,5.385 3.781,5.583 0.99,0.198 10 false *: Shielded 4.938,2.885 5.552,3.083 0.615,0.198 10 false 1 4.927,3.719 5.542,3.917 0.615,0.198 10 false 2

CAUTION / NOTICE / HINT

CAUTION:
·

Wear insulated gloves and pull out the service plug grip before inspection as procedures may require disconnecting high-voltage connectors. Carry the removed service plug in your pocket to prevent other technicians from accidentally reconnecting it while you are servicing the vehicle.

·

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.



NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.


·

The hybrid control system and air conditioning system output DTCs separately. Perform troubleshooting for the hybrid control system first if DTCs from these systems are output simultaneously.

·

Depending on the timing of the power supply to the 12 V power supply circuit and high-voltage circuit when the power switch is turned on (READY), an abnormal information signal may be output, causing this DTC to be stored. If the output DTC is a code that was memorized in the past, check the fuses and wire harnesses. If there is no malfunction, clear the DTC.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Using the GTS, check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
Result Proceed to
CAN communication system DTCs are not output A
CAN communication system DTCs are output B



A

2.CHECK FOR DTC (HYBRID CONTROL SYSTEM)

B

2.CHECK FOR DTC (HYBRID CONTROL SYSTEM)

A

3.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY - HYBRID VEHICLE CONTROL ECU ASSEMBLY)

B

3.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
a.

Disconnect the C52 compressor with motor assembly connector.


b.

Disconnect the A29 hybrid vehicle control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C52-3 (DOUT) - A29-8 (LIN3) Always Below 1 Ω
C52-3 (DOUT) - A29-8 (LIN3) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY - BATTERY AND BODY GROUND)
CAUTION:

Do not disconnect the connector on the high-voltage side.


a.
E366609C04
0.333,0.948 0.833,1.198 0.5,0.25 2.167,0.281 1.917,0.281 1.917,0.281 1.688,1.052 true 0.75,0.5 1,0.5 1,0.5 1.458,1.073 true 0.083,0.104 0.396,0.302 0.313,0.198 10 false *a 0.458,0.99 0.771,1.188 0.313,0.198 10 false C52 2.219,0.188 2.604,0.385 0.385,0.198 10 false GND 0.49,0.406 0.875,0.604 0.385,0.198 10 false IG1
*a Front view of wire harness connector
(to Compressor with Motor Assembly)


Disconnect the compressor with motor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C52-2 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C52-1 (IG1) - Body ground Power switch on (IG) 11 to 14 V
Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

5.CHECK HV AIR CONDITIONING WIRE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HV AIR CONDITIONING WIRE
CAUTION:

Be sure to wear insulated gloves.


a.

Disconnect the Z1 and Z2 HV air conditioning wire connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z1-2 (PB) - Z2-1 (ACPB) Always Below 1 Ω
Z1-1 (PE) - Z2-2 (ACPE) Always Below 1 Ω
Z1-2 (PB) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG