Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for HV Model) › from 2020.05
RM3620E _58 Vehicle Interior _076130 HEATING / AIR CONDITIONING _0370842 AIR CONDITIONING SYSTEM(for HV Model) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for HV Model)  P1C7C49  Hybrid/EV Battery Voltage System Isolation (A/C Area) Internal Electronic Failure  


DESCRIPTION

This DTC is stored if there is insulation malfunction in the high-voltage circuit in the air conditioning system. Possible causes are poor insulation in the compressor with motor assembly, or mixing of any oil other than ND-OIL 11 in the refrigerant cycle.

A high-voltage motor is built into the compressor with motor assembly and is cooled directly with refrigerant. Compressor oil (ND-OIL 11) with high insulation performance is used because a leakage of electrical power may occur if regular compressor oil (ND-OIL 8) is used.

CAUTION:
·

Wear insulated gloves and pull out the service plug grip before inspection as procedures may require disconnecting high-voltage connectors. Carry the removed service plug in your pocket to prevent other technicians from accidentally reconnecting it while you are servicing the vehicle.

·

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.



DTC No. Detection Item DTC Detection Condition Trouble Area Memory
P1C7C49 Hybrid/EV Battery Voltage System Isolation (A/C Area) Internal Electronic Failure High voltage system insulation malfunction
·

Compressor oil

·

Refrigerant pipe line

·

Compressor with motor assembly

·

CAN communication system


Memorized

WIRING DIAGRAM

E414323E02
3.51,0.781 4.125,0.979 0.615,0.198 10 false LIN3 3.281,0.615 3.896,0.813 0.615,0.198 10 false 8 2.969,1.229 3.583,1.427 0.615,0.198 10 false A29 2.958,1.406 4.719,1.823 1.76,0.417 10 false Hybrid Vehicle Control ECU Assembly 3.198,2.188 4.781,2.417 1.583,0.229 10 false from IG1 NO.1 Relay 5.5,1.302 7.083,1.698 1.583,0.396 10 false Air Conditioning Amplifier Assembly 1.958,2.344 3.083,2.563 1.125,0.219 10 false ECU-IG1 NO.3 1.542,0.792 2.156,0.99 0.615,0.198 10 false C52 1.625,0.563 2.24,0.76 0.615,0.198 10 false 3 1.552,2.208 2.167,2.406 0.615,0.198 10 false C52 1.615,1.979 2.229,2.177 0.615,0.198 10 false 1 1.552,2.615 2.167,2.813 0.615,0.198 10 false C52 1.625,2.427 2.24,2.625 0.615,0.198 10 false 2 1.604,3.042 2.219,3.24 0.615,0.198 10 false Z1 1.635,2.823 2.25,3.021 0.615,0.198 10 false 2 1.604,3.865 2.219,4.063 0.615,0.198 10 false Z1 1.625,3.656 2.24,3.854 0.615,0.198 10 false 1 1.031,0.802 1.646,1 0.615,0.198 10 false DOUT 1.177,2.198 1.792,2.396 0.615,0.198 10 false IG1 1.104,2.625 1.719,2.823 0.615,0.198 10 false GND 1.219,3.052 1.833,3.25 0.615,0.198 10 false PB 1.313,3.448 1.927,3.646 0.615,0.198 10 false E 1.292,4.26 1.906,4.458 0.615,0.198 10 false E 1.219,3.865 1.833,4.063 0.615,0.198 10 false PE 5.135,3.458 5.75,3.656 0.615,0.198 10 false E 5.135,4.292 5.75,4.49 0.615,0.198 10 false E 5.135,3.719 5.75,3.917 0.615,0.198 10 false ACPE 5.135,2.885 5.75,3.083 0.615,0.198 10 false ACPB 0.313,4.729 1.427,5.115 1.115,0.385 10 false Compressor with Motor Assembly 2.656,4.698 4.354,4.885 1.698,0.188 10 false HV Air Conditioning Wire 4.958,4.885 7.031,5.146 2.073,0.26 10 false Inverter with Converter Assembly 4.969,4.719 6.938,4.979 1.969,0.26 10 false Z2 0.76,5.406 2.99,5.604 2.229,0.198 10 false : CAN Communication Line 0.76,5.865 2.99,6.063 2.229,0.198 10 false : LIN Communication Line 0.771,6.333 3,6.531 2.229,0.198 10 false : High Voltage Line 3.229,3.542 3.844,3.74 0.615,0.198 10 false * 3.25,4.385 3.865,4.583 0.615,0.198 10 false * 2.792,5.385 3.781,5.583 0.99,0.198 10 false *: Shielded 4.938,2.885 5.552,3.083 0.615,0.198 10 false 1 4.927,3.719 5.542,3.917 0.615,0.198 10 false 2

CAUTION / NOTICE / HINT

CAUTION:
·

Wear insulated gloves and pull out the service plug grip before inspection as procedures may require disconnecting high-voltage connectors. Carry the removed service plug in your pocket to prevent other technicians from accidentally reconnecting it while you are servicing the vehicle.

·

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.



NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.


·

Electrical insulation performance may decrease significantly if even a small amount of oil other than ND-OIL 11 is used (or enters) in the refrigerant cycle, causing a DTC to be output.

·

If other oil is accidentally used and a DTC is output, collect as much oil in the refrigerant cycle into the compressor with motor assembly as possible and replace it with ND-OIL 11 to increase the ND-OIL 11 ratio amount.

·

Replace the main components of the air conditioning cycle (evaporator, condenser, and compressor) if a large amount of oil other than ND-OIL 11 enters the system. Failing to do so may cause electrical insulation performance to remain low, causing a DTC to be output.

·

The hybrid control system and air conditioning system output DTCs separately. Perform troubleshooting for the hybrid control system first if DTCs from these systems are output simultaneously.



HINT:

If it can be confirmed that any compressor oil other than ND-OIL 11 has been used in the vehicle, replace the main components of the air conditioning cycle.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Using the GTS, check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
Result Proceed to
CAN communication system DTCs are not output A
CAN communication system DTCs are output B



A

2.CLEAR DTC

B

2.CLEAR DTC
a.

Clear the DTCs.


Powertrain > Hybrid Control > Clear DTCs
50002 397
HINT:

When DTC P1C7C49 is output, the power switch cannot be turned on (READY), so use the GTS and clear DTC P1C7C49.



Result:
Proceed to
NEXT



NEXT

3.INSPECT COMPRESSOR WITH MOTOR ASSEMBLY
3.INSPECT COMPRESSOR WITH MOTOR ASSEMBLY
CAUTION:

Because the compressor with motor assembly has a high-voltage circuit, wear insulated gloves and pull out the service plug grip to cut off the high-voltage circuit before inspection.


a.

Turn the power switch on (READY).


b.

Prepare the vehicle according to the table below for 3 minutes.

Item Condition
Blower Speed HI
Set Temperature MAX COLD
A/C Switch On


c.

Turn the power switch off.



CAUTION:

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.


NOTICE:

After removing the service plug grip, turning the power switch on (READY) may cause a malfunction. Do not turn the power switch on (READY) with the service plug grip removed.


e.
E334624C07
1.479,0.385 1.979,0.635 0.5,0.25 1.552,1.302 1.354,1.75 1.354,1.75 1.104,1.75 true 1.938,1.281 2.25,1.75 2.25,1.75 2.5,1.75 true 0.385,0.375 0.698,0.573 0.313,0.198 10 false *a 0.875,1.677 1.188,1.875 0.313,0.198 10 false PB 2.552,1.677 2.865,1.875 0.313,0.198 10 false PE 1.656,0.417 1.969,0.615 0.313,0.198 10 false Z1
*a Component without harness connected
(Compressor with Motor Assembly)


Disconnect the compressor with motor assembly connector.


f.

Using a megohmmeter, measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z1-1 (PE) - Body ground Always 2 MΩ or higher
Z1-2 (PB) - Body ground Always 2 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT AIR CONDITIONING CYCLE

NG

4.INSPECT AIR CONDITIONING CYCLE
CAUTION:

Because the compressor with motor assembly has a high-voltage circuit, wear insulated gloves and pull out the service plug grip to cut off the high-voltage circuit before inspection.


a.

Reconnect the Z1 the compressor with motor assembly connector.



c.

Turn the power switch on (READY).


d.

Set the A/C temperature to 25°C (77°F) and blower switch to LO and then operate the compressor with motor assembly for 10 minutes to circulate the refrigerant and collect as much compressor oil as possible in the compressor with motor assembly.


e.

Turn the power switch off.


f.

Using a spot cooler or other tool, cool down the compressor with motor assembly for 30 minutes, or leave the vehicle overnight before inspection.

NOTICE:

Do not operate the compressor before inspection.



g.

Remove the service plug grip.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>SERVICE PLUG GRIP>REMOVAL

CAUTION:

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.


NOTICE:

After removing the service plug grip, turning the power switch on (READY) may cause a malfunction. Do not turn the power switch on (READY) with the service plug grip removed.



h.
E334624C07
1.479,0.385 1.979,0.635 0.5,0.25 1.552,1.302 1.354,1.75 1.354,1.75 1.104,1.75 true 1.938,1.281 2.25,1.75 2.25,1.75 2.5,1.75 true 0.385,0.375 0.698,0.573 0.313,0.198 10 false *a 0.875,1.677 1.188,1.875 0.313,0.198 10 false PB 2.552,1.677 2.865,1.875 0.313,0.198 10 false PE 1.656,0.417 1.969,0.615 0.313,0.198 10 false Z1
*a Component without harness connected
(Compressor with Motor Assembly)


Disconnect the compressor with motor assembly connector.


i.

Using a megohmmeter, measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z1-1 (PE) - Body ground Always 3 MΩ or higher
Z1-2 (PB) - Body ground Always 3 MΩ or higher


NOTICE:

If the results are out of the specified range, replace the compressor without operating it.



Result:
Proceed to
OK
NG



OK

NG

REPLACE AIR CONDITIONING CYCLE