This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
17169A
1.INSTALL NO. 3 EXHAUST MANIFOLD HEAT INSULATOR
Install the No. 3 exhaust manifold heat insulator to the cylinder block sub-assembly with the bolt.
11452
2.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
Apply a light coat of engine oil to a new O-ring.
Install the O-ring to the engine oil level dipstick guide.
Using an 8 mm socket wrench, install the engine oil level dipstick guide to the cylinder head sub-assembly with the bolt.
Install the engine oil level dipstick.
19500
3.INSTALL IGNITION COIL ASSEMBLY
23255A
4.INSTALL FUEL INJECTOR SEAL
23250E
5.INSTALL DIRECT FUEL INJECTOR ASSEMBLY
23814B
6.INSTALL FUEL DELIVERY PIPE
23250F
7.INSTALL PORT FUEL INJECTOR ASSEMBLY
82125N
8.INSTALL NO. 5 ENGINE WIRE
23291
9.INSTALL INJECTOR VIBRATION INSULATOR
23807V
10.INSTALL NO. 1 DELIVERY PIPE SPACER
23807
11.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY
12.INSTALL WIRE HARNESS CLAMP BRACKET
Using an 8 mm socket wrench, install the wire harness clamp bracket to the No. 1 ventilation case with the 2 bolts.
82126A
13.INSTALL NO. 6 ENGINE WIRE
Install the No. 6 engine wire to the wire harness clamp bracket with the 2 nuts.
Attach the 2 clamps.
Connect the 4 connectors.
82219A
14.INSTALL SENSOR WIRE
Using an 8 mm socket wrench, install the sensor wire to the water inlet with thermostat sub-assembly with the bolt.
Attach the 3 clamps.
Connect the 4 connectors.
16295
15.INSTALL NO. 7 WATER BY-PASS HOSE
Install the No. 7 water by-pass hose and slide the 2 clips to secure them.
23100X
16.TEMPORARILY INSTALL FUEL PUMP ASSEMBLY (for High Pressure)
23801P
17.TEMPORARILY INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY
23100X
18.INSTALL FUEL PUMP ASSEMBLY (for High Pressure)
23801P
19.INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY
| *a | 17 mm Union Nut Wrench |
| *b | Torque Wrench Fulcrum Length |
|
Union Nut |
|
Bolt |
Using a 17 mm union nut wrench, tighten the union nut on the fuel delivery pipe side of the No. 1 fuel pipe sub-assembly.
Do not adjust the torque in the loosening direction.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)
Using a 17 mm union nut wrench, tighten the union nut on the fuel pump assembly side of the No. 1 fuel pipe sub-assembly.
Do not adjust the torque in the loosening direction.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)
Connect the No. 1 fuel pipe sub-assembly to the cylinder head sub-assembly with the bolt.
23901
20.CONNECT FUEL TUBE SUB-ASSEMBLY
17177
21.INSTALL NO. 1 INTAKE MANIFOLD TO HEAD GASKET
17111
22.INSTALL INTAKE MANIFOLD
16278
23.INSTALL NO. 2 WATER BY-PASS PIPE
Install the bolt (A).
Using an 8 mm socket wrench, install the No. 2 water by-pass pipe with the 2 bolts (B) in the order shown in the illustration.
16279
24.INSTALL NO. 3 WATER BY-PASS PIPE
Connect the No. 3 water by-pass pipe to the water outlet and slide the clip to secure it.
Using an 8 mm socket wrench, install the No. 3 water by-pass pipe to the intake manifold with the bolt.
25620
25.INSTALL EGR VALVE ASSEMBLY
Using an 8 mm socket wrench, install the EGR valve bracket with the bolt.
| *a | Pin |
| *b | Hole |
Align and fit the hole of the EGR valve bracket to the pin of the camshaft housing sub-assembly.
Using the 8 mm socket wrench, install the EGR valve assembly with the EGR valve bracket to the camshaft housing sub-assembly with the bolt.
Connect the No. 8 water by-pass hose to the EGR valve assembly and slide the clip to secure it.
26.INSTALL WATER HOSE
Connect the water hose to the EGR valve assembly and slide the clip to secure it.
25601
27.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY
25680
28.INSTALL EGR COOLER ASSEMBLY
Install the EGR cooler assembly, a new EGR cooler gasket and a new EGR valve gasket with the 5 bolts.
Connect the No. 3 water by-pass hose to the EGR cooler assembly and slide the clip to secure it.
Connect the water hose to the EGR cooler assembly and slide the clip to secure it.
22030
29.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY
17141
30.INSTALL EXHAUST MANIFOLD
17118
31.INSTALL MANIFOLD STAY
17167
32.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
w/o GPF:
Install the No. 1 exhaust manifold heat insulator to the exhaust manifold with the 3 bolts.
w/ GPF:
Install the No. 1 exhaust manifold heat insulator to the exhaust manifold with the 3 bolts.
25706
33.INSTALL NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/ GPF)
25760
34.INSTALL VACUUM TRANSMITTING HOSE ASSEMBLY (w/ GPF)
89481B
35.INSTALL DIFFERENTIAL PRESSURE SENSOR (w/ GPF)
16260
36.INSTALL FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY)
Install the water hose clamp bracket with the 2 bolts as shown in the illustration.
Temporarily install the bolt (A), and then tighten the 2 bolts in the order of (B) and (A).
| *a | Paint Mark |
| *b | 90° (Claw of Clip Location) |
Connect the flow shutting valve (water by-pass hose assembly) to the water by-pass outlet sub-assembly and slide the clip to secure it.
Make sure to slide the flow shutting valve (water by-pass hose assembly) until it contacts the hose stopper of the water by-pass outlet sub-assembly.
Make sure that the claws of the clip are within the location shown in the illustration.
Connect the flow shutting valve (water by-pass hose assembly) with the bolt.
16207
37.INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY
Connect the No. 2 water by-pass pipe sub-assembly with the bolt.
Connect the No. 2 water by-pass pipe sub-assembly to the outlet water by-pass sub-assembly and slide the clip to secure it.
88310
38.INSTALL COMPRESSOR ASSEMBLY WITH PULLEY
Using an E8 "TORX" socket wrench, temporarily install the compressor with motor assembly with the 2 stud bolts.
|
Bolt |
|
Nut |
Install the compressor with motor assembly with the bolt and 2 nuts.
Tighten the bolt and nuts in the order shown in the illustration.
43457
39.INSTALL DRIVE SHAFT BEARING BRACKET
Install the drive shaft bearing bracket with the 3 bolts.