64910N
1.REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
Remove the tonneau cover assembly.
58410B
2.REMOVE DECK BOARD ASSEMBLY
Remove the deck board assembly.
58416K
3.REMOVE REAR NO. 2 FLOOR BOARD
Detach the clip and guide and remove the rear No. 2 floor board.
58417H
4.REMOVE REAR NO. 3 FLOOR BOARD
Detach the clip and guide and remove the rear No. 3 floor board.
64993
5.REMOVE REAR DECK FLOOR BOX (w/o Spare Tire)
Remove the clip and rear deck floor box.
64779K
6.REMOVE SPARE WHEEL COVER STOPPER (w/ Spare Tire)
Remove the spare wheel cover stopper.
7.REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY
72693
8.REMOVE REAR SEAT CUSHION LOCK HOOK
67918E
9.REMOVE REAR DOOR SCUFF PLATE LH
for Gasoline Model:
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the removal direction to detach the claw and guide.
|
Place Hands Here |
|
Remove in this Direction |
Place both hands at the position shown in the illustration and lift in the direction indicated by the arrow to detach the claw and guide and remove the rear door scuff plate LH.
for HV Model:
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the removal direction to detach the claw and guide.
|
Place Hands Here |
|
Remove in this Direction |
Place both hands at the position shown in the illustration and lift in the direction indicated by the arrow to detach the claw, clip and guide and remove the rear door scuff plate LH.
67917C
10.REMOVE REAR DOOR SCUFF PLATE RH
Use the same procedure described for the LH side.
58386
11.REMOVE REAR FLOOR FINISH PLATE
Detach the claw and clip and remove the rear floor finish plate.
12.REMOVE REAR SEATBACK ASSEMBLY LH
73350C
13.REMOVE REAR CENTER SEAT OUTER BELT ASSEMBLY (FLOOR ANCHOR)
14.REMOVE REAR SEATBACK ASSEMBLY RH
58466J
15.REMOVE NO. 2 BATTERY SERVICE COVER BOARD (for HV Model)
58467H
16.REMOVE NO. 3 BATTERY SERVICE COVER BOARD (for HV Model)
58464D
17.REMOVE BATTERY SERVICE COVER BOARD (for HV Model)
71304C
18.REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY LH
71303C
19.REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
73706
20.REMOVE CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH
73705
21.REMOVE CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
Click hereVehicle Interior>SEAT BELT>CHILD RESTRAINT SEAT ANCHOR BRACKET>REMOVAL
58577E
22.REMOVE REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE
Remove the 2 screws.
Detach the clip and claw and remove the rear No. 1 floor mat support side plate.
62332C
23.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
62331C
24.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure described for the LH side.
67914B
25.REMOVE FRONT DOOR SCUFF PLATE LH
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the removal direction to detach the claw and guide.
|
Place Hands Here |
|
Remove in this Direction |
Place both hands at the position shown in the illustration and lift in the direction indicated by the arrow to detach the claw and guide and remove the front door scuff plate LH.
67913B
26.REMOVE FRONT DOOR SCUFF PLATE RH
Use the same procedure described for the LH side.
62112
27.REMOVE COWL SIDE TRIM BOARD LH
62111C
28.REMOVE COWL SIDE TRIM BOARD RH
Use the same procedure described for the LH side.
62312B
29.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
62311B
30.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure described for the LH side.
62212
31.REMOVE FRONT PILLAR GARNISH LH
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the front pillar garnish clip.
| *a | Release Lever |
|
Push |
Push in the release lever with your finger and remove the front pillar garnish clip from the vehicle.
When the front pillar garnish clip cannot be detached by pressing the knobs with the fingers:
|
Direction (A) |
|
Push |
Lift up the front pillar garnish clip in the direction (A) while pressing the portion indicated by the arrow in the illustration with your fingers.
|
Direction (B) |
|
Release Lever |
|
Push |
Push in the portion indicated by the arrow in the illustration with the screwdriver end while pulling the front pillar garnish clip with your fingers in the direction (B) to detach the front pillar garnish clip.
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the front pillar garnish clip.
| *a | Release Lever |
|
Push |
Push in the release lever with your finger and remove the front pillar garnish clip from the vehicle.
When the front pillar garnish clip cannot be detached by pressing the knobs with the fingers:
|
Direction (A) |
|
Push |
Lift up the front pillar garnish clip in the direction (A) while pressing the portion indicated by the arrow in the illustration with your fingers.
|
Direction (B) |
|
Release Lever |
|
Push |
Push in the portion indicated by the arrow in the illustration with the screwdriver end while pulling the front pillar garnish clip with your fingers in the direction (B) to detach the front pillar garnish clip.
|
Remove in this Direction |
Pull in the direction of the arrow shown in the illustration to detach the guide and remove the front pillar garnish LH.
for 9 Speakers:
Disconnect the connector.
| *a | Protective Cover |
|
Adhesive Tape |
Protect curtain shield airbag assembly:
Cover the airbag with a cloth or piece of nylon and secure both ends of the cover with adhesive tape as shown in the illustration.
Cover the curtain shield airbag assembly with a protective cover as soon as the front pillar garnish assembly LH is removed.
62211
32.REMOVE FRONT PILLAR GARNISH RH
Use the same procedure described for the LH side.
73233
33.REMOVE OUTER LAP BELT ANCHOR COVER
Use the same procedure for both outer lap belt anchor covers.
Detach the claw and guide and remove the outer lap belt anchor cover.
73220
34.REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH
Remove the bolt and remove the front seat outer belt assembly LH.
73210
35.REMOVE FRONT SEAT OUTER BELT ASSEMBLY RH
Use the same procedure described for the LH side.
62414A
36.REMOVE LOWER CENTER PILLAR GARNISH LH
|
Place Hands Here |
|
Remove in this Direction |
Pull both sides of the lower center pillar garnish LH outward to detach the claw as shown in the illustration.
Detach the clip and remove the lower center pillar garnish LH.
62413A
37.REMOVE LOWER CENTER PILLAR GARNISH RH
Use the same procedure described for the LH side.
62412
38.REMOVE CENTER PILLAR GARNISH LH
|
Place Hands Here |
|
Remove in this Direction |
Remove the 2 clips.
Place both hands at the position shown in the illustration, detach the clip and remove the center pillar garnish LH.
When reusing the center pillar garnish LH:
Remove the clip.
62411
39.REMOVE CENTER PILLAR GARNISH RH
Use the same procedure described for the LH side.
62552F
40.REMOVE REAR SEAT SIDE GARNISH LH
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration, and detach the claw.
|
Remove in this Direction |
Detach the clip and claw and remove the rear seat side garnish LH as shown in the illustration.
62551F
41.REMOVE REAR SEAT SIDE GARNISH RH
Use the same procedure described for the LH side.
73708A
42.REMOVE TETHER ANCHOR BRACKET SET
Use the same procedure for the opposite side.
|
Turn Up in this Direction |
Detach the claw and turn the cover up as shown in the illustration.
Loosen the bolt and remove the tether anchor bracket set.
58460D
43.REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY
Use the same procedure for the opposite side.
Remove the bolt.
Detach the guide and remove the luggage hold belt striker assembly.
64740E
44.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
Remove the clip.
except "TORX" Type:
Remove the screw.
for "TORX" Type:
Using a T30 "TORX" socket wrench, remove the "TORX" screw.
Detach the clip, claw and guide and remove the deck trim side panel assembly LH.
|
Clip |
|
Screw or "TORX" Screw |
64730J
45.REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH
Remove the clip.
except "TORX" Type:
Remove the screw.
for "TORX" Type:
Using a T30 "TORX" socket wrench, remove the "TORX" screw.
Detach the clip, claw and guide and remove the deck trim side panel assembly RH.
|
Clip |
|
Screw or "TORX" Screw |
Disconnect each connector.
62480A
46.REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH
Detach the clip and remove the inner roof side garnish assembly LH.
| *a | Clip A | *b | Clip B |
| *c | Clip C | - | - |
When reusing the inner roof side garnish assembly LH:
Remove the 8 clips.
| *a | Clip A | *b | Clip B |
| *c | Clip C | - | - |
62470A
47.REMOVE INNER ROOF SIDE GARNISH ASSEMBLY RH
Use the same procedure described for the LH side.
74320
48.REMOVE VISOR ASSEMBLY LH
except "TORX" Type:
Remove the 2 screws.
for "TORX" Type:
Using a T25 "TORX" socket wrench, remove the 2 "TORX" screws.
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Pull in the direction of the arrow shown in the illustration (1) to detach the visor assembly LH from the visor holder LH.
Pull in the direction of the arrow shown in the illustration (2) and remove the visor assembly LH.
Do not twist or remove the visor assembly in any direction other than downwards as the connector may become damaged.
74310
49.REMOVE VISOR ASSEMBLY RH
Use the same procedure described for the LH side.
74348
50.REMOVE VISOR HOLDER
Use the same procedure for the opposite side.
| *a | 45° |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Turn the visor holder end approximately 45° in the direction (1) indicated by the arrow shown in the illustration, and pull it out in the direction (2) indicated by the arrow.
Detach the claw and remove the visor holder base.
74610U
51.REMOVE ASSIST GRIP ASSEMBLY
Use the same procedure for all assist grip assemblies.
| *a | Cutout |
Insert SST into the cutout of the assist grip cover LH as shown in the illustration.
To prevent the assist grip assembly from being damaged, make sure to insert SST straight into the cutout.
| *a | 30 to 45° |
|
Remove in this Direction |
Pull SST as shown in the illustration to detach the claw.
To prevent the assist grip assembly from being damaged, make sure to only pull SST as shown in the illustration.
Use the same procedure for the claw on the other side of the assist grip cover LH.
Remove the assist grip cover LH.
Use the same procedure for the LH side and RH side.
Pinch the clip with needle-nose pliers.
Use the same procedure for both clips.
|
Remove in this Direction |
Hold the handle and pull in the direction indicated by the arrow shown in the illustration to remove the assist grip assembly.
Using needle-nose pliers, remove the clip.
74630E
52.REMOVE REAR ASSIST GRIP ASSEMBLY LH
Use the same procedure as for the assist grip assembly.
74620C
53.REMOVE REAR ASSIST GRIP ASSEMBLY RH
Use the same procedure as for the assist grip assembly.
54.REMOVE MAP LIGHT ASSEMBLY
81240
55.REMOVE NO. 1 ROOM LIGHT ASSEMBLY
89943
56.REMOVE RAIN SENSOR COVER (w/ Rain Sensor)
86466E
57.REMOVE NO. 2 FORWARD RECOGNITION COVER (w/ Pre-collision System)
86466D
58.REMOVE NO. 1 FORWARD RECOGNITION COVER (w/ Pre-collision System)
87834
59.REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror, w/o Pre-collision System)
63318C
60.REMOVE SUN ROOF OPENING TRIM MOULDING (for Moon Roof)
Remove the sun roof opening trim moulding.
61.REMOVE ROOF HEADLINING ASSEMBLY (for Normal Roof)
for Front Pillar LH Side:
Remove the protective cover installed to the front pillar LH.
Disconnect the 2 connectors.
Using a clip remover, detach the wire harness clamp.
Install the protective cover to the front pillar LH.
for Front Pillar RH Side:
Remove the protective cover installed to the front pillar RH.
Disconnect the connector.
Using a clip remover, detach the wire harness clamp.
Install the protective cover to the front pillar RH.
for Rear Pillar LH Side:
Disconnect the connector.
for Rear Pillar RH Side:
Disconnect the connector.
for LHD:
| *A | w/ Rain Sensor |
w/o EC Mirror, w/o Pre-collision System:
Disconnect the connector.
| *A | w/ Rain Sensor |
w/o EC Mirror, w/ Pre-collision System:
Disconnect each connector.
| *A | w/ Rain Sensor |
w/ EC Mirror, w/o Pre-collision System:
Disconnect each connector.
| *A | w/ Rain Sensor |
w/ EC Mirror, w/ Pre-collision System:
Disconnect each connector.
| *A | w/ Rain Sensor |
w/ Digital Inner Mirror, w/ Pre-collision System:
Disconnect each connector.
for RHD:
| *A | w/ Rain Sensor |
w/o EC Mirror, w/o Pre-collision System:
Disconnect the connector.
| *A | w/ Rain Sensor |
w/o EC Mirror, w/ Pre-collision System:
Disconnect each connector.
| *A | w/ Rain Sensor |
w/ EC Mirror, w/o Pre-collision System:
Disconnect each connector.
| *A | w/ Rain Sensor |
w/ EC Mirror, w/ Pre-collision System:
Disconnect each connector.
| *A | w/ Rain Sensor |
w/ Digital Inner Mirror, w/ Pre-collision System:
Disconnect each connector.
Remove the 5 clips.
|
Remove in this Direction |
Turn the roof headlining assembly diagonally and bend slightly to remove it from the back door.
Make sure that wrinkles do not form in the roof headlining assembly during removal.
Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.
Do not damage the roof headlining assembly or vehicle interior.
2 or more people are required when carrying the roof headlining assembly out of the vehicle, as it may become deformed.
62.REMOVE ROOF HEADLINING ASSEMBLY (for Moon Roof)
for Front Pillar LH Side:
Remove the protective cover installed to the front pillar LH.
Disconnect the 2 connectors.
Using a clip remover, detach the wire harness clamp.
Install the protective cover to the front pillar LH.
for Front Pillar RH Side:
Remove the protective cover installed to the front pillar RH.
Disconnect the connector.
Using a clip remover, detach the wire harness clamp.
Install the protective cover to the front pillar RH.
for Rear Pillar LH Side:
Disconnect the connector.
for Rear Pillar RH Side:
Disconnect the connector.
for LHD:
| *A | w/ Rain Sensor |
w/o EC Mirror, w/o Pre-collision System:
Disconnect the connector.
| *A | w/ Rain Sensor |
w/o EC Mirror, w/ Pre-collision System:
Disconnect each connector.
| *A | w/ Rain Sensor |
w/ EC Mirror, w/o Pre-collision System:
Disconnect each connector.
| *A | w/ Rain Sensor |
w/ EC Mirror, w/ Pre-collision System:
Disconnect each connector.
| *A | w/ Rain Sensor |
w/ Digital Inner Mirror, w/ Pre-collision System:
Disconnect each connector.
for RHD:
| *A | w/ Rain Sensor |
w/o EC Mirror, w/o Pre-collision System:
Disconnect the connector.
| *A | w/ Rain Sensor |
w/o EC Mirror, w/ Pre-collision System:
Disconnect each connector.
| *A | w/ Rain Sensor |
w/ EC Mirror, w/o Pre-collision System:
Disconnect each connector.
| *A | w/ Rain Sensor |
w/ EC Mirror, w/ Pre-collision System:
Disconnect each connector.
| *A | w/ Rain Sensor |
w/ Digital Inner Mirror, w/ Pre-collision System:
Disconnect each connector.
Disconnect the connector.
Remove the 3 clips.
|
Remove in this Direction |
Turn the roof headlining assembly diagonally and bend slightly to remove it from the back door.
Make sure that wrinkles do not form in the roof headlining assembly during removal.
Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.
Do not damage the roof headlining assembly or vehicle interior.
2 or more people are required when carrying the roof headlining assembly out of the vehicle, as it may become deformed.
63.REMOVE ROOF HEADLINING ASSEMBLY (for Panoramic Moon Roof)
for Front Pillar LH Side:
Remove the protective cover installed to the front pillar LH.
Disconnect the 2 connectors.
Using a clip remover, detach the wire harness clamp.
Install the protective cover to the front pillar LH.
for Front Pillar RH Side:
Remove the protective cover installed to the front pillar RH.
Disconnect the connector.
Using a clip remover, detach the wire harness clamp.
Install the protective cover to the front pillar RH.
for Rear Pillar LH Side:
Disconnect the connector.
for Rear Pillar RH Side:
Disconnect the connector.
for LHD:
| *A | w/ Rain Sensor |
w/o EC Mirror, w/o Pre-collision System:
Disconnect the connector.
| *A | w/ Rain Sensor |
w/o EC Mirror, w/ Pre-collision System:
Disconnect each connector.
| *A | w/ Rain Sensor |
w/ EC Mirror, w/o Pre-collision System:
Disconnect each connector.
| *A | w/ Rain Sensor |
w/ EC Mirror, w/ Pre-collision System:
Disconnect each connector.
| *A | w/ Rain Sensor |
w/ Digital Inner Mirror, w/ Lane Departure Alert System:
Disconnect each connector.
for RHD:
| *A | w/ Rain Sensor |
w/o EC Mirror, w/o Pre-collision System:
Disconnect the connector.
| *A | w/ Rain Sensor |
w/o EC Mirror, w/ Pre-collision System:
Disconnect each connector.
| *A | w/ Rain Sensor |
w/ EC Mirror, w/o Pre-collision System:
Disconnect each connector.
| *A | w/ Rain Sensor |
w/ EC Mirror, w/ Pre-collision System:
Disconnect each connector.
| *A | w/ Rain Sensor |
w/ Digital Inner Mirror, w/ Pre-collision System:
Disconnect each connector.
Disconnect the 2 connectors.
Remove the 3 clips.
Detach the fastener and guide.
| *a | Fastener | *b | Guide |
|
Remove in this Direction |
Turn the roof headlining assembly diagonally and bend slightly to remove it from the back door.
Make sure that wrinkles do not form in the roof headlining assembly during removal.
Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.
Do not damage the roof headlining assembly or vehicle interior.
2 or more people are required when carrying the roof headlining assembly out of the vehicle, as it may become deformed.
66425B
64.REMOVE REAR NO. 2 SIDE RAIL SPACER LH
Perform this procedure only when replacing the rear No. 2 side rail spacer LH.
Detach the claw and remove the rear No. 2 side rail spacer LH.
66415B
65.REMOVE REAR NO. 2 SIDE RAIL SPACER RH
Perform this procedure only when replacing the rear No. 2 side rail spacer RH.
Use the same procedure described for the LH side.
64230A
66.REMOVE ROOM PARTITION NET ASSEMBLY (w/ Partition Net)
Perform this procedure only when replacing the room partition net assembly.
| *A | for HV Model |
| *B | for Gasoline Model |
Detach the claw and guide and remove the room partition net assembly.
64783C
67.REMOVE DECK TRIM POCKET COVER PLATE (except Partition Net)
Perform this procedure only when replacing the deck trim pocket cover plate.
| *A | for HV Model |
| *B | for Gasoline Model |
Detach the claw and guide and remove the deck trim pocket cover plate.
65351A
68.REMOVE BATTERY HOLE COVER (for HV Model)
Perform this procedure only when replacing the battery hole cover.
Detach the claw and remove the battery hole cover.