Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
A bolt without a torque specification is shown in the standard bolt chart.
Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS
65351A
1.INSTALL BATTERY HOLE COVER (for HV Model)
Attach the claw to install the battery hole cover.
64783C
2.INSTALL DECK TRIM POCKET COVER PLATE (except Partition Net)
| *A | for HV Model |
| *B | for Gasoline Model |
Attach the guide and claw to install the deck trim pocket cover plate.
64230A
3.INSTALL ROOM PARTITION NET ASSEMBLY (w/ Partition Net)
| *A | for HV Model |
| *B | for Gasoline Model |
Attach the guide and claw to install the room partition net assembly.
66425B
4.INSTALL REAR NO. 2 SIDE RAIL SPACER LH
Attach the claw to install the rear No. 2 side rail spacer LH.
66415B
5.INSTALL REAR NO. 2 SIDE RAIL SPACER RH
Use the same procedure described for the LH side.
6.INSTALL ROOF HEADLINING ASSEMBLY (for Normal Roof)
|
Install in this Direction |
Insert the roof headlining assembly into the cabin from the back door.
Installation of the roof headlining assembly must be performed by multiple people to prevent deformation of the roof headlining assembly.
Check that the corners of the roof headlining are not folded, twisted or otherwise deformed and that none of the mounted parts have fallen off.
Make sure that the roof headlining does not get caught on anything as it may become bent or damaged.
Do not damage the roof headlining or vehicle interior.
Attach the claw to install the visor holder base.
Use the same procedure for the opposite side.
Install 5 new clips.
for LHD:
| *A | w/ Rain Sensor |
w/o EC Mirror, w/o Pre-collision System:
Connect the connector.
| *A | w/ Rain Sensor |
w/o EC Mirror, w/ Pre-collision System:
Connect each connector.
| *A | w/ Rain Sensor |
w/ EC Mirror, w/o Pre-collision System:
Connect each connector.
| *A | w/ Rain Sensor |
w/ EC Mirror, w/ Pre-collision System:
Connect each connector.
| *A | w/ Rain Sensor |
w/ Digital Inner Mirror, w/ Pre-collision System:
Connect each connector.
for RHD:
| *A | w/ Rain Sensor |
w/o EC Mirror, w/o Pre-collision System:
Connect the connector.
| *A | w/ Rain Sensor |
w/o EC Mirror, w/ Pre-collision System:
Connect each connector.
| *A | w/ Rain Sensor |
w/ EC Mirror, w/o Pre-collision System:
Connect each connector.
| *A | w/ Rain Sensor |
w/ EC Mirror, w/ Pre-collision System:
Connect each connector.
| *A | w/ Rain Sensor |
w/ Digital Inner Mirror, w/ Pre-collision System:
Connect each connector.
for Rear Pillar LH Side:
Connect the connector.
for Rear Pillar RH Side:
Connect the connector.
for Front Pillar LH Side:
Remove the protective cover installed to the front pillar LH.
Attach the wire harness clamp.
Connect the 2 connectors.
Install the protective cover to the front pillar LH.
for Front Pillar RH Side:
Remove the protective cover installed to the front pillar RH.
Attach the wire harness clamp.
Connect the connector.
Install the protective cover to the front pillar RH.
7.INSTALL ROOF HEADLINING ASSEMBLY (for Moon Roof)
|
Install in this Direction |
Insert the roof headlining assembly into the cabin from the back door.
Installation of the roof headlining assembly must be performed by multiple people to prevent deformation of the roof headlining assembly.
Check that the corners of the roof headlining are not folded, twisted or otherwise deformed and that none of the mounted parts have fallen off.
Make sure that the roof headlining does not get caught on anything as it may become bent or damaged.
Do not damage the roof headlining or vehicle interior.
Attach the claw to install the visor holder base.
Use the same procedure for the opposite side.
Install 3 new clips.
Connect the connector.
for LHD:
| *A | w/ Rain Sensor |
w/o EC Mirror, w/o Pre-collision System:
Connect the connector.
| *A | w/ Rain Sensor |
w/o EC Mirror, w/ Pre-collision System:
Connect each connector.
| *A | w/ Rain Sensor |
w/ EC Mirror, w/o Pre-collision System:
Connect each connector.
| *A | w/ Rain Sensor |
w/ EC Mirror, w/ Pre-collision System:
Connect each connector.
| *A | w/ Rain Sensor |
w/ Digital Inner Mirror, w/ Pre-collision System:
Connect each connector.
for RHD:
| *A | w/ Rain Sensor |
w/o EC Mirror, w/o Pre-collision System:
Connect the connector.
| *A | w/ Rain Sensor |
w/o EC Mirror, w/ Pre-collision System:
Connect each connector.
| *A | w/ Rain Sensor |
w/ EC Mirror, w/o Pre-collision System:
Connect each connector.
| *A | w/ Rain Sensor |
w/ EC Mirror, w/ Pre-collision System:
Connect each connector.
| *A | w/ Rain Sensor |
w/ Digital Inner Mirror, w/ Pre-collision System:
Connect each connector.
for Rear Pillar LH Side:
Connect the connector.
for Rear Pillar RH Side:
Connect the connector.
for Front Pillar LH Side:
Remove the protective cover installed to the front pillar LH.
Attach the wire harness clamp.
Connect the 2 connectors.
Install the protective cover to the front pillar LH.
for Front Pillar RH Side:
Remove the protective cover installed to the front pillar RH.
Attach the wire harness clamp.
Connect the connector.
Install the protective cover to the front pillar RH.
8.INSTALL ROOF HEADLINING ASSEMBLY (for Panoramic Moon Roof)
|
Install in this Direction |
Insert the roof headlining assembly into the cabin from the back door.
Installation of the roof headlining assembly must be performed by multiple people to prevent deformation of the roof headlining assembly.
Check that the corners of the roof headlining are not folded, twisted or otherwise deformed and that none of the mounted parts have fallen off.
Make sure that the roof headlining does not get caught on anything as it may become bent or damaged.
Do not damage the roof headlining or vehicle interior.
Attach the claw to install the visor holder base.
Use the same procedure for the opposite side.
Attach the guide and fastener to install the roof headlining assembly.
| *a | Guide | *b | Fastener |
Install 3 new clips.
Connect the 2 connectors.
for LHD:
| *A | w/ Rain Sensor |
w/o EC Mirror, w/o Pre-collision System:
Connect the connector.
| *A | w/ Rain Sensor |
w/o EC Mirror, w/ Pre-collision System:
Connect each connector.
| *A | w/ Rain Sensor |
w/ EC Mirror, w/o Pre-collision System:
Connect each connector.
| *A | w/ Rain Sensor |
w/ EC Mirror, w/ Pre-collision System:
Connect each connector.
| *A | w/ Rain Sensor |
w/ Digital Inner Mirror, w/ Pre-collision System:
Connect each connector.
for RHD:
| *A | w/ Rain Sensor |
w/o EC Mirror, w/o Pre-collision System:
Connect the connector.
| *A | w/ Rain Sensor |
w/o EC Mirror, w/ Pre-collision System:
Connect each connector.
| *A | w/ Rain Sensor |
w/ EC Mirror, w/o Pre-collision System:
Connect each connector.
| *A | w/ Rain Sensor |
w/ EC Mirror, w/ Pre-collision System:
Connect each connector.
| *A | w/ Rain Sensor |
w/ Digital Inner Mirror, w/ Pre-collision System:
Connect each connector.
for Rear Pillar LH Side:
Connect the connector.
for Rear Pillar RH Side:
Connect the connector.
for Front Pillar LH Side:
Remove the protective cover installed to the front pillar LH.
Attach the wire harness clamp.
Connect the 2 connectors.
Install the protective cover to the front pillar LH.
for Front Pillar RH Side:
Remove the protective cover installed to the front pillar RH.
Attach the wire harness clamp.
Connect the connector.
Install the protective cover to the front pillar RH.
63318C
9.INSTALL SUN ROOF OPENING TRIM MOULDING (for Moon Roof)
| *a | Sun Roof Opening Trim Moulding Fabric Cover |
| *b | Cutout of the Roof Headlining Assembly |
Install the sun roof opening trim moulding as shown in the illustration.
87834
10.INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror, w/o Pre-collision System)
86466D
11.INSTALL NO. 1 FORWARD RECOGNITION COVER (w/ Pre-collision System)
86466E
12.INSTALL NO. 2 FORWARD RECOGNITION COVER (w/ Pre-collision System)
89943
13.INSTALL RAIN SENSOR COVER (w/ Rain Sensor)
81240
14.INSTALL NO. 1 ROOM LIGHT ASSEMBLY
15.INSTALL MAP LIGHT ASSEMBLY
74610U
16.INSTALL ASSIST GRIP ASSEMBLY
Use the same procedure for all assist grip assemblies.
Install the 2 clips to the assist grip assembly.
Temporarily install the 2 assist grip covers to the assist grip assembly as shown in the illustration.
Attach the clip to install the assist grip assembly.
Attach the claw to install the 2 assist grip covers.
Check that the 2 clips are securely attached.
74630E
17.INSTALL REAR ASSIST GRIP ASSEMBLY LH
Use the same procedure as for the assist grip assembly.
74620C
18.INSTALL REAR ASSIST GRIP ASSEMBLY RH
Use the same procedure as for the assist grip assembly.
74348
19.INSTALL VISOR HOLDER
Use the same procedure for the opposite side.
|
Install in this Direction |
Push in the end of the visor holder to install the visor holder.
74320
20.INSTALL VISOR ASSEMBLY LH
|
Install in this Direction |
Set the visor assembly LH into place by aligning it upward with the connector and screw fastening hole.
When setting the part into place, move it straight upward so as not to damage the connector.
Hold the visor assembly with one hand so that it does not drop.
Connect the visor assembly LH to the visor holder LH to set it into place.
except "TORX" Type:
Install the visor assembly LH with the 2 screws.
for "TORX" Type:
Using a T25 "TORX" socket wrench, install the visor assembly LH with the 2 "TORX" screws.
74310
21.INSTALL VISOR ASSEMBLY RH
Use the same procedure described for the LH side.
62480A
22.INSTALL INNER ROOF SIDE GARNISH ASSEMBLY LH
When reusing the inner roof side garnish assembly LH:
Install 8 new clips to the inner roof side garnish assembly LH.
| *a | Clip A | *b | Clip B |
| *c | Clip C | - | - |
Attach the clip to install the inner roof side garnish assembly LH.
| *a | Clip A | *b | Clip B |
| *c | Clip C | - | - |
62470A
23.INSTALL INNER ROOF SIDE GARNISH ASSEMBLY RH
Use the same procedure described for the LH side.
64740E
24.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
Attach the guide, claw and clip to install the deck trim side panel assembly LH.
except "TORX" Screw:
Install the screw.
for "TORX" Screw:
Using a T30 "TORX" socket wrench, install the "TORX" screw.
Install the clip.
|
Clip |
|
Screw or "TORX" Screw |
64730J
25.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
Connect each connector.
Attach the guide, claw and clip to install the deck trim side panel assembly RH.
except "TORX" Screw:
Install the screw.
for "TORX" Screw:
Using a T30 "TORX" socket wrench, install the "TORX" screw.
Install the clip.
|
Clip |
|
Screw or "TORX" Screw |
58460D
26.INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY
Use the same procedure for the opposite side.
Attach the guide to install the luggage hold belt striker assembly with the bolt.
73708A
27.INSTALL TETHER ANCHOR BRACKET SET
Use the same procedure for the opposite side.
Tighten the bolt to install the tether anchor bracket set.
|
Install in this Direction |
Attach the claw as shown in the illustration.
62552F
28.INSTALL REAR SEAT SIDE GARNISH LH
|
Install in this Direction |
Attach the claw and clip to install the rear seat side garnish LH as shown in the illustration.
|
Install in this Direction |
Attach the claw as shown in the illustration.
62551F
29.INSTALL REAR SEAT SIDE GARNISH RH
Use the same procedure described for the LH side.
62412
30.INSTALL CENTER PILLAR GARNISH LH
When reusing the center pillar garnish LH:
Install a new clip.
|
Install in this Direction |
Attach the clip to install the center pillar garnish LH as shown in the illustration.
Install the 2 clips.
62411
31.INSTALL CENTER PILLAR GARNISH RH
Use the same procedure described for the LH side.
62414A
32.INSTALL LOWER CENTER PILLAR GARNISH LH
|
Install in this Direction |
Attach the clip and claw to install the lower center pillar garnish LH as shown in the illustration.
62413A
33.INSTALL LOWER CENTER PILLAR GARNISH RH
Use the same procedure described for the LH side.
73220
34.INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH
Install the front seat outer belt assembly LH with the bolt.
73210
35.INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH
Use the same procedure described for the LH side.
73233
36.INSTALL OUTER LAP BELT ANCHOR COVER
Use the same procedure for both outer lap belt anchor covers.
Attach the guide and claw to install the outer lap belt anchor cover.
62212
37.INSTALL FRONT PILLAR GARNISH LH
Install new 2 front pillar garnish clips to the front pillar garnish LH.
Make sure that the position and direction of the front pillar garnish clip is correct when installing.
Peel off the adhesive tape and remove the protective cover.
|
Install in this Direction |
Insert the guide in the direction indicated by the arrow shown in the illustration.
|
Install in this Direction |
Push in the direction indicated by the arrow shown in the illustration to attach the clip to install the front pillar garnish LH.
62211
38.INSTALL FRONT PILLAR GARNISH RH
Use the same procedure described for the LH side.
62312B
39.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
62311B
40.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure described for the LH side.
62112
41.INSTALL COWL SIDE TRIM BOARD LH
62111C
42.INSTALL COWL SIDE TRIM BOARD RH
Use the same procedure described for the LH side.
67914B
43.INSTALL FRONT DOOR SCUFF PLATE LH
|
Install in this Direction |
Attach the claw and align the guide in the direction indicated by the arrow shown in the illustration.
|
Place Hand Here |
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Push in the installation direction (1) shown in the illustration to attach the claw on the vehicle exterior side and align the guide.
Place your hand at the position shown in the illustration and attach the claw while pulling in the installation direction (2) to install the front door scuff plate LH.
67913B
44.INSTALL FRONT DOOR SCUFF PLATE RH
Use the same procedure described for the LH side.
62332C
45.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
62331C
46.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure described for the LH side.
58577E
47.INSTALL REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE
Attach the claw and clip to install the rear No. 1 floor mat support side plate with the 2 screws.
73706
48.INSTALL CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH
73705
49.INSTALL CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
Click hereVehicle Interior>SEAT BELT>CHILD RESTRAINT SEAT ANCHOR BRACKET>INSTALLATION
71304C
50.INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY LH
71303C
51.INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>INSTALLATION
58464D
52.INSTALL BATTERY SERVICE COVER BOARD (for HV Model)
58467H
53.INSTALL NO. 3 BATTERY SERVICE COVER BOARD (for HV Model)
58466J
54.INSTALL NO. 2 BATTERY SERVICE COVER BOARD (for HV Model)
55.INSTALL REAR SEATBACK ASSEMBLY LH
56.INSTALL REAR SEATBACK ASSEMBLY RH
73350C
57.INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY (FLOOR ANCHOR)
58386
58.INSTALL REAR FLOOR FINISH PLATE
Attach the claw and clip to install the rear floor finish plate.
67918E
59.INSTALL REAR DOOR SCUFF PLATE LH
for Gasoline Model:
|
Install in this Direction |
Attach the claw and align the guide in the direction indicated by the arrow shown in the illustration.
|
Place Hand Here |
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Push in the installation direction (1) shown in the illustration to attach the claw on the vehicle exterior side and align the guide.
Place your hand at the position shown in the illustration and attach the claw while pulling in the installation direction (2) to install the rear door scuff plate LH.
for HV Model:
|
Install in this Direction |
Attach the claw and clip and align the guide in the direction indicated by the arrow shown in the illustration.
|
Place Hand Here |
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Push in the installation direction (1) shown in the illustration to attach the claw on the vehicle exterior side and align the guide.
Place your hand at the position shown in the illustration and attach the claw while pulling in the installation direction (2) to install the rear door scuff plate LH.
67917C
60.INSTALL REAR DOOR SCUFF PLATE RH
Use the same procedure described for the LH side.
72693
61.INSTALL REAR SEAT CUSHION LOCK HOOK
62.INSTALL BENCH TYPE REAR SEAT CUSHION ASSEMBLY
64779K
63.INSTALL SPARE WHEEL COVER STOPPER (w/ Spare Tire)
Install the spare wheel cover stopper.
64993
64.INSTALL REAR DECK FLOOR BOX (w/o Spare Tire)
Install the rear deck floor box with the clip.
58417H
65.INSTALL REAR NO. 3 FLOOR BOARD
Attach the guide and clip to install the rear No. 3 floor board.
58416K
66.INSTALL REAR NO. 2 FLOOR BOARD
Attach the guide and clip to install the rear No. 2 floor board.
58410B
67.INSTALL DECK BOARD ASSEMBLY
Install the deck board assembly.
64910N
68.INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
Install the tonneau cover assembly.
69.INSPECT SEAT BELT WARNING SYSTEM (w/ Occupant Detection Sensor)
70.INSPECT SEAT HEATER SYSTEM (w/ Seat Heater System)