PRECAUTION FOR OPERATION CHECK
Use the correct procedure to replace the airbag parts.
CHECK SRS WARNING LIGHT
Primary check
Turn the ignition switch to ON and check that the SRS warning light turns on.
Turn the ignition switch off. Wait for at least 2 seconds, and then turn the ignition switch to ON. The SRS warning light comes on for approximately 6 seconds and diagnosis of the airbag system (including the seat belt pretensioners) is performed.
Turn the ignition switch off when the auxiliary battery is connected.
If the warning light remains on for approximately 6 seconds or more after the ignition switch has been turned to ON, there may be a malfunction with the SRS airbag system.
If the warning light occasionally turns on approximately 6 seconds or more after the ignition switch has been turned to ON, there may be a short to +B, short to ground or an open in the SRS warning light circuit.
If the warning light illuminates after turning the ignition switch off or ACC, there may be a malfunction in the power source circuit or combination meter assembly.
The SRS warning light turns off, and then turns on. This blinking pattern indicates a source voltage drop. The SRS warning light turns off 10 seconds after the source voltage returns to normal.
FUNCTION OF PASSENGER AIRBAG ON/OFF INDICATOR (w/ Airbag Cutoff Switch)
Initial check
Turn the ignition switch to ON.
The passenger airbag ON/OFF indicator comes on for approximately 4 seconds, and then goes off for approximately 2 seconds.
Approximately 6 seconds after the ignition switch is turned to ON, the passenger airbag ON/OFF indicator will indicate ON/OFF according to the airbag cutoff switch cylinder sub-assembly condition as listed below.
| Airbag Cutoff Switch Cylinder Sub-assembly Condition | Passenger Airbag ON/OFF Indicator | SRS Warning Light | |
|---|---|---|---|
| ON Indicator | OFF Indicator | ||
| ON | ON | OFF | OFF |
| OFF | OFF | ON | OFF |
| Switch failure | OFF | ON | ON |
If the passenger airbag ON/OFF indicator does not operate as specified in the table according to the airbag cutoff switch cylinder sub-assembly status and the SRS warning light is not illuminated, no DTC will be output. Therefore, perform troubleshooting for trouble in passenger airbag ON/OFF indicator.
CHECK PASSENGER AIRBAG ON/OFF INDICATOR (w/ Airbag Cutoff Switch)
Turn the ignition switch to ON.
Check that the passenger airbag ON/OFF indicator ("ON" and "OFF") comes on for approximately 4 seconds, and then goes off for approximately 2 seconds.
In order to check the operation of the passenger airbag ON/OFF indicator when approximately 6 seconds have elapsed after turning the ignition switch to ON, refer to the table in the previous step.
CHECK HORN BUTTON ASSEMBLY
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>ON-VEHICLE INSPECTION
CHECK INSTRUMENT PANEL PASSENGER WITHOUT DOOR AIRBAG ASSEMBLY
CHECK LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>KNEE AIRBAG ASSEMBLY>ON-VEHICLE INSPECTION
CHECK FRONT SEAT AIRBAG ASSEMBLY
for Manual Seat:
for Power Seat:
CHECK CURTAIN SHIELD AIRBAG ASSEMBLY
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CURTAIN SHIELD AIRBAG ASSEMBLY>ON-VEHICLE INSPECTION
CHECK FRONT SEAT OUTER BELT ASSEMBLY
Click hereVehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY>ON-VEHICLE INSPECTION
CHECK REAR SEAT OUTER BELT ASSEMBLY (w/ Rear Pretensioner)
Click hereVehicle Interior>SEAT BELT>REAR SEAT OUTER BELT ASSEMBLY>ON-VEHICLE INSPECTION
CHECK AIRBAG SENSOR ASSEMBLY
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>ON-VEHICLE INSPECTION
CHECK FRONT AIRBAG SENSOR
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>FRONT AIRBAG SENSOR>ON-VEHICLE INSPECTION
CHECK FLOOR SIDE AIRBAG SENSOR
CHECK NO. 2 SIDE AIRBAG SENSOR ASSEMBLY (w/ Rear Airbag Sensor)
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>REAR AIRBAG SENSOR>ON-VEHICLE INSPECTION
CHECK SIDE AIRBAG PRESSURE SENSOR
CHECK HARNESS AND CONNECTOR
for Vehicle not Involved in Collision
Perform a diagnostic system check.
for Vehicle Involved in Collision and Airbag not Deployed
Perform a diagnostic system check.
for Vehicle Involved in Collision and Airbag is Deployed
Perform a diagnostic system check.
Check any of the wire harnesses in exposed contact with the airbag wire harness for damage.
Check the connector of the airbag wire harness for scratches, cracks or damage.