Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2020.08
RM3620E _58 Vehicle Interior _076051 METER / GAUGE / DISPLAY _0374621 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speed Signal Circuit  


DESCRIPTION

The combination meter assembly receives the vehicle speed signal from this circuit. The wheel speed sensors produce an output that varies according to the vehicle speed. The wheel speed sensor output is received by the skid control ECU which uses this information to create the vehicle speed signal*a. The vehicle speed signal consists of pulses sent to the combination meter assembly from the skid control ECU. To create this signal, 12 V is output from IG2 which is behind a resistor in the combination meter assembly. This voltage is sent to the skid control ECU. The pulse signal is created by switching the transistor in the skid control ECU on and off, making the voltage on the wire drop to 0 V. A similar system is used for the output of this signal from the combination meter assembly via terminal +S. A voltage of 12 V or 5 V is applied to terminal +S from each ECU or relay that is connected to this terminal. The transistor in the combination meter assembly is controlled by the signal from the skid control ECU. When this transistor is turned on, this transistor makes the voltage supplied by the various ECUs (via their respective internal resistors) drop to 0 V. Each ECU connected to terminal +S of the combination meter assembly controls its respective system based on this pulse signal.

*a: This vehicle speed signal is created by the skid control ECU. There is no actual component that is referred to as the vehicle speed sensor. In addition, for some systems, vehicle speed information may be received via CAN communication.


HINT:

This circuit is used for the systems connected to terminal +S. This signal is not used for combination meter assembly operation. Combination meter assembly components such as the speedometer operate using data received via CAN communication.


WIRING DIAGRAM

for HV Model:
C448907E02
0.542,1.25 2.229,1.448 1.688,0.198 10 false A42 0.552,1.396 3.385,1.729 2.833,0.333 10 false Brake Booster with Master Cylinder Assembly (Skid Control ECU) 1.813,0.479 3.5,0.677 1.688,0.198 10 false 11 1.406,0.479 1.865,0.677 0.458,0.198 10 false SP1 5.479,0.604 5.938,0.802 0.458,0.198 10 false SI 5.177,0.479 5.635,0.677 0.458,0.198 10 false 20 5.469,2.552 5.927,2.75 0.458,0.198 10 false +S 5.188,2.438 5.646,2.635 0.458,0.198 10 false 36 1.813,2.438 2.271,2.635 0.458,0.198 10 false 19 1.417,2.438 1.875,2.635 0.458,0.198 10 false SPD 0.448,2.865 0.906,3.063 0.458,0.198 10 false G54 0.438,3.031 3.51,3.604 3.073,0.573 10 false Certification ECU (Smart Key ECU Assembly) 0.438,4.479 0.896,4.677 0.458,0.198 10 false M3 0.427,4.677 3.5,5.167 3.073,0.49 10 false Stereo Component Amplifier Assembly*1 5.396,4.49 5.854,4.688 0.458,0.198 10 false H7 5.396,4.615 6.854,5.125 1.458,0.51 10 false Navigation ECU*2 1.406,4.052 1.865,4.25 0.458,0.198 10 false SPD 5.458,4.052 5.917,4.25 0.458,0.198 10 false SPD 5.302,4.042 5.76,4.24 0.458,0.198 10 false 9 1.802,4.042 2.26,4.24 0.458,0.198 10 false 11 1.427,5.625 1.885,5.823 0.458,0.198 10 false SPD 1.844,5.604 2.302,5.802 0.458,0.198 10 false 27 0.49,6.042 2.208,6.563 1.719,0.521 10 false G3 5.146,2.896 5.604,3.094 0.458,0.198 10 false G18 5.146,3.083 7.073,3.552 1.927,0.469 10 false Combination Meter Assembly 0.313,7.188 3.083,7.563 2.771,0.375 10 false *1: for 9 Speakers 0.302,7.677 3.073,8.052 2.771,0.375 10 false *2: w/ Navigation System 0.302,8.198 3.073,8.573 2.771,0.375 10 false *3: for Radio and Display Type 0.49,6.26 2.208,6.781 1.719,0.521 10 false Radio and Display Receiver Assembly*3

for Gasoline Model:
C429439E08
0.573,1.135 2.26,1.333 1.688,0.198 10 false A39 1.813,0.385 3.5,0.583 1.688,0.198 10 false 34 1.406,0.385 1.865,0.573 0.458,0.188 10 false SP1 5.479,0.479 5.938,0.677 0.458,0.198 10 false SI 5.177,0.375 5.635,0.573 0.458,0.198 10 false 20 5.469,2.406 5.927,2.604 0.458,0.198 10 false +S 5.188,2.344 5.646,2.542 0.458,0.198 10 false 36 1.813,2.333 2.271,2.531 0.458,0.198 10 false 19 1.417,2.354 1.875,2.552 0.458,0.198 10 false SPD 0.448,2.729 0.906,2.927 0.458,0.198 10 false G54 0.438,2.885 3.51,3.458 3.073,0.573 10 false Certification ECU (Smart Key ECU Assembly)*1 0.438,4.333 0.896,4.531 0.458,0.198 10 false M3 0.438,4.479 3.51,4.969 3.073,0.49 10 false Stereo Component Amplifier Assembly*2 0.635,5.896 1.094,6.094 0.458,0.198 10 false H7 0.635,6.052 2.094,6.563 1.458,0.51 10 false Navigation ECU*3 1.406,3.969 1.865,4.167 0.458,0.198 10 false SPD 1.417,5.521 1.875,5.719 0.458,0.198 10 false SPD 1.823,5.521 2.281,5.719 0.458,0.198 10 false 9 1.802,3.948 2.26,4.146 0.458,0.198 10 false 11 5.219,3.948 6,4.146 0.781,0.198 10 false 42 5.458,3.958 5.917,4.156 0.458,0.198 10 false SPD 5.458,5.51 5.917,5.708 0.458,0.198 10 false SPD 5.448,7.094 5.938,7.292 0.49,0.198 10 false SPDP 5.198,5.521 5.656,5.719 0.458,0.198 10 false 27 5.177,7.063 5.635,7.26 0.458,0.198 10 false 10 4.917,7.427 5.375,7.625 0.458,0.198 10 false H6 4.896,7.615 7.146,8.042 2.25,0.427 10 false Telephone Transceiver Assembly*6 4.656,5.885 5.115,6.083 0.458,0.198 10 false G3 4.635,6.042 7.146,6.552 2.51,0.51 10 false Radio and Display Receiver Assembly*4 5.531,4.344 6.594,4.542 1.063,0.198 10 false A24 5.531,4.5 6.406,4.74 0.875,0.24 10 false ECM 5.146,2.698 5.604,2.896 0.458,0.198 10 false G18 5.146,2.844 7.073,3.313 1.927,0.469 10 false Combination Meter Assembly 0.344,7.604 3.115,7.979 2.771,0.375 10 false Transmission Control ECU*5 0.354,7.458 0.813,7.656 0.458,0.198 10 false C33 1.427,7.073 1.885,7.271 0.458,0.198 10 false SPD 1.813,7.063 2.594,7.26 0.781,0.198 10 false 42 2.875,8.198 5.563,8.625 2.688,0.427 10 false *4: for Radio and Display Type 2.854,9.177 6.167,9.563 3.313,0.385 10 false *6: w/ Telematics System (for ERA-GLONASS) 0.177,8.229 2.167,8.625 1.99,0.396 10 false *1: w/ Entry and Start System 0.177,8.667 2.167,9.063 1.99,0.396 10 false *2: for 9 Speakers 0.177,9.135 2.167,9.531 1.99,0.396 10 false *3: w/ Navigation System 2.844,8.688 6.063,8.865 3.219,0.177 10 false *5: for Continuously Variable Transaxle 0.563,1.302 2.198,1.667 1.635,0.365 10 false Brake Actuator Assembly (Skid Control ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the ECM or certification ECU (smart key ECU assembly) refer to Service Bulletin.

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.CHECK ECU TERMINAL VOLTAGE (INPUT VOLTAGE)
C406366C02
1.5,0.125 1.885,0.385 0.385,0.26 2.552,1.385 2.917,1.792 2.917,1.792 3.083,1.792 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.583,0.188 1.896,0.344 0.313,0.156 10 false G18 3.146,1.677 3.417,1.906 0.271,0.229 10 false +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


a.

Disconnect the combination meter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G18-36 (+S) - Body ground Ignition switch ON 11 to 14 V


HINT:

If any of the ECUs specified in the wiring diagram supplies power to the combination meter assembly, the combination meter assembly will output a waveform.



Result:
Result Proceed to
OK (for Gasoline Model) A
OK (for HV Model) B
NG C



A

2.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

B

5.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

C

8.CHECK HARNESS AND CONNECTOR (EACH ECU - COMBINATION METER ASSEMBLY)
2.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
E376462C04
1.51,0.177 1.927,0.427 0.417,0.25 0.646,0.333 0.771,0.333 0.771,0.333 1.25,0.906 true 1.604,0.198 2.063,0.396 0.458,0.198 10 false A39 0.344,0.229 0.802,0.427 0.458,0.198 10 false SP1 0.115,0.063 0.573,0.26 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


a.

Disconnect the brake actuator assembly (skid control ECU) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A39-34 (SP1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (INPUT WAVEFORM)

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])
3.CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (INPUT WAVEFORM)
E391284C07
1.448,0.438 1.865,0.667 0.417,0.229 1.031,1.323 0.521,1.042 0.521,1.042 0.344,1.042 true 1.542,0.469 1.854,0.667 0.313,0.198 10 false G18 0.146,0.927 0.458,1.125 0.313,0.198 10 false SI 2.948,3.698 3.406,3.896 0.458,0.198 10 false GND 1.281,3.979 1.438,4.177 0.156,0.198 10 false A 0.177,0.24 0.49,0.438 0.313,0.198 10 false *a 0.448,2.458 0.76,2.656 0.313,0.198 10 false *b
*a Component with harness connected
(Combination Meter Assembly)
*b Waveform


a.

Check the input waveform.

i.

Remove the combination meter assembly with the connector(s) still connected.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


ii.

Connect an oscilloscope to terminal G18-20 (SI) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tester connection G18-20 (SI) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Condition Ignition switch ON, wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])
a.

Disconnect the G18 combination meter assembly connector.


b.

Disconnect the A39 brake actuator assembly (skid control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G18-20 (SI) - A39-34 (SP1) Always Below 1 Ω
G18-20 (SI) or A39-34 (SP1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
E292914C03
0.979,0.094 1.479,0.344 0.5,0.25 2.073,0.906 2.458,0.302 2.458,0.302 2.615,0.302 true 2.677,0.135 3.021,0.323 0.344,0.188 10 false SP1 1.094,0.115 1.552,0.313 0.458,0.198 10 false A42 0.146,0.094 0.458,0.292 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly [Skid Control ECU])


a.

Disconnect the brake booster with master cylinder assembly (skid control ECU) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A42-11 (SP1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU) (INPUT WAVEFORM)

NG

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [SKID CONTROL ECU])
6.CHECK BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU) (INPUT WAVEFORM)
E391284C07
1.448,0.438 1.865,0.667 0.417,0.229 1.031,1.323 0.521,1.042 0.521,1.042 0.344,1.042 true 1.542,0.469 1.854,0.667 0.313,0.198 10 false G18 0.146,0.927 0.458,1.125 0.313,0.198 10 false SI 2.948,3.698 3.406,3.896 0.458,0.198 10 false GND 1.281,3.979 1.438,4.177 0.156,0.198 10 false A 0.177,0.24 0.49,0.438 0.313,0.198 10 false *a 0.448,2.458 0.76,2.656 0.313,0.198 10 false *b
*a Component with harness connected
(Combination Meter Assembly)
*b Waveform


a.

Check the input waveform.

i.

Remove the combination meter assembly with the connector(s) still connected.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


ii.

Connect an oscilloscope to terminal G18-20 (SI) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tester connection G18-20 (SI) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Condition Ignition switch ON, wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [SKID CONTROL ECU])
a.

Disconnect the G18 combination meter assembly connector.


b.

Disconnect the A42 brake booster with master cylinder assembly (skid control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G18-20 (SI) - A42-11 (SP1) Always Below 1 Ω
G18-20 (SI) or A42-11 (SP1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (EACH ECU - COMBINATION METER ASSEMBLY)

*1: for Gasoline Model

*2: for Continuously Variable Transaxle

*3: w/ Telematics System (for ERA-GLONASS)

*4: for Radio and Display Type

*5: w/ Entry and Start System

*6: w/ Navigation System

*7: for 9 Speakers


a.
C406366C02
1.5,0.125 1.885,0.385 0.385,0.26 2.552,1.385 2.917,1.792 2.917,1.792 3.083,1.792 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.583,0.188 1.896,0.344 0.313,0.156 10 false G18 3.146,1.677 3.417,1.906 0.271,0.229 10 false +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the A24 ECM connector.*1


c.

Disconnect the C33 transmission control ECU connector.*2


d.

Disconnect the H6 telephone transceiver assembly connector.*3


e.

Disconnect the G3 radio and display receiver assembly connector.*4


f.

Disconnect the G54 certification ECU (smart key ECU assembly) connector.*5


g.

Disconnect the H7 navigation ECU connector.*6


h.

Disconnect the M3 stereo component amplifier assembly connector.*7


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G18-36 (+S) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for Gasoline Model) A
OK (for HV Model) B
NG C



A

9.CHECK VEHICLE TYPE

B

21.CHECK VEHICLE TYPE

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
w/ Entry and Start System A
w/o Entry and Start System B



A

10.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (SHORT CIRCUIT IN CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

B

11.CHECK VEHICLE TYPE
10.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (SHORT CIRCUIT IN CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
C406366C02
1.5,0.125 1.885,0.385 0.385,0.26 2.552,1.385 2.917,1.792 2.917,1.792 3.083,1.792 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.583,0.188 1.896,0.344 0.313,0.156 10 false G18 3.146,1.677 3.417,1.906 0.271,0.229 10 false +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


a.

Disconnect the combination meter assembly connector.


b.

Disconnect the G54 certification ECU (smart key ECU assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G18-36 (+S) - Body ground Ignition switch ON 11 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the certification ECU (smart key ECU assembly).



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

11.CHECK VEHICLE TYPE
11.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
w/ Telematics System (for ERA-GLONASS) A
w/o Telematics System (for ERA-GLONASS) B



A

12.CHECK TELEPHONE TRANSCEIVER ASSEMBLY

B

13.CHECK VEHICLE TYPE
12.CHECK TELEPHONE TRANSCEIVER ASSEMBLY
a.
C406366C02
1.5,0.125 1.885,0.385 0.385,0.26 2.552,1.385 2.917,1.792 2.917,1.792 3.083,1.792 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.583,0.188 1.896,0.344 0.313,0.156 10 false G18 3.146,1.677 3.417,1.906 0.271,0.229 10 false +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the H6 telephone transceiver assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G18-36 (+S) - Body ground Ignition switch ON 11 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the telephone transceiver assembly.



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

13.CHECK VEHICLE TYPE
13.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
w/ Navigation System A
w/o Navigation System B



A

14.CHECK NAVIGATION ECU

B

15.CHECK VEHICLE TYPE
14.CHECK NAVIGATION ECU
a.
C406366C02
1.5,0.125 1.885,0.385 0.385,0.26 2.552,1.385 2.917,1.792 2.917,1.792 3.083,1.792 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.583,0.188 1.896,0.344 0.313,0.156 10 false G18 3.146,1.677 3.417,1.906 0.271,0.229 10 false +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the H7 navigation ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G18-36 (+S) - Body ground Ignition switch ON 11 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the navigation ECU.



Result:
Proceed to
OK
NG



OK

NG

15.CHECK VEHICLE TYPE
15.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
for Continuously Variable Transaxle A
except Continuously Variable Transaxle B



A

16.CHECK TRANSMISSION CONTROL ECU

B

17.CHECK VEHICLE TYPE
16.CHECK TRANSMISSION CONTROL ECU
a.
C406366C02
1.5,0.125 1.885,0.385 0.385,0.26 2.552,1.385 2.917,1.792 2.917,1.792 3.083,1.792 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.583,0.188 1.896,0.344 0.313,0.156 10 false G18 3.146,1.677 3.417,1.906 0.271,0.229 10 false +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the C33 transmission control ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G18-36 (+S) - Body ground Ignition switch ON 11 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the transmission control ECU.



Result:
Proceed to
OK
NG



OK

REPLACE TRANSMISSION CONTROL ECU

NG

17.CHECK VEHICLE TYPE
17.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
for Radio and Display Type A
except Radio and Display Type B



A

18.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

B

19.CHECK VEHICLE TYPE
18.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
C406366C02
1.5,0.125 1.885,0.385 0.385,0.26 2.552,1.385 2.917,1.792 2.917,1.792 3.083,1.792 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.583,0.188 1.896,0.344 0.313,0.156 10 false G18 3.146,1.677 3.417,1.906 0.271,0.229 10 false +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the G3 radio and display receiver assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G18-36 (+S) - Body ground Ignition switch ON 11 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the radio and display receiver assembly.



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

19.CHECK VEHICLE TYPE
19.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
for 9 Speakers A
except 9 Speakers B



A

20.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY

B

20.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY
a.
C406366C02
1.5,0.125 1.885,0.385 0.385,0.26 2.552,1.385 2.917,1.792 2.917,1.792 3.083,1.792 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.583,0.188 1.896,0.344 0.313,0.156 10 false G18 3.146,1.677 3.417,1.906 0.271,0.229 10 false +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the M3 stereo component amplifier assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G18-36 (+S) - Body ground Ignition switch ON 11 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the stereo component amplifier assembly.



Result:
Proceed to
OK
NG



OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

21.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
w/ Navigation System A
w/o Navigation System B



A

22.CHECK NAVIGATION ECU

B

23.CHECK VEHICLE TYPE
22.CHECK NAVIGATION ECU
a.
C406366C02
1.5,0.125 1.885,0.385 0.385,0.26 2.552,1.385 2.917,1.792 2.917,1.792 3.083,1.792 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.583,0.188 1.896,0.344 0.313,0.156 10 false G18 3.146,1.677 3.417,1.906 0.271,0.229 10 false +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the H7 navigation ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G18-36 (+S) - Body ground Ignition switch ON 11 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the navigation ECU.



Result:
Proceed to
OK
NG



OK

NG

23.CHECK VEHICLE TYPE
23.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
for Radio and Display Type A
except Radio and Display Type B



A

24.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

B

25.CHECK VEHICLE TYPE
24.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
C406366C02
1.5,0.125 1.885,0.385 0.385,0.26 2.552,1.385 2.917,1.792 2.917,1.792 3.083,1.792 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.583,0.188 1.896,0.344 0.313,0.156 10 false G18 3.146,1.677 3.417,1.906 0.271,0.229 10 false +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the G3 radio and display receiver assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G18-36 (+S) - Body ground Ignition switch ON 11 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the radio and display receiver assembly.



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

25.CHECK VEHICLE TYPE
25.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
for 9 Speakers A
except 9 Speakers B



A

26.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

26.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY
a.
C406366C02
1.5,0.125 1.885,0.385 0.385,0.26 2.552,1.385 2.917,1.792 2.917,1.792 3.083,1.792 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.583,0.188 1.896,0.344 0.313,0.156 10 false G18 3.146,1.677 3.417,1.906 0.271,0.229 10 false +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the M3 stereo component amplifier assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G18-36 (+S) - Body ground Ignition switch ON 11 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the stereo component amplifier assembly.



Result:
Proceed to
OK
NG



OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)