Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › ULTRASONIC SENSOR (for Rear) › from 2020.08
RM3620E _56 Audio / Visual / Telematics _076129 PARK ASSIST / MONITORING _0370877 ULTRASONIC SENSOR(for Rear) A

PARK ASSIST / MONITORING  ULTRASONIC SENSOR(for Rear)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during ultrasonic sensor (for Rear) removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) auxiliary battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system for A25A-FKS:(Click here)
for M20A-FKS:(Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
Ultrasonic sensor (Including removal and installation)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

TOYOTA parking assist-sensor system (for Gasoline model with parking support brake system)

·

Parking support brake system (for Gasoline model)


(Click here)
Kick door control sensor Reset connection history There are cases where the connection history display differs from the vehicle condition (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) auxiliary battery terminal Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
Ultrasonic sensor (Including removal and installation)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

TOYOTA parking assist-sensor system (for HV model with parking support brake system)

·

Parking support brake system (for HV model)


(Click here)
Kick door control sensor Reset connection history There are cases where the connection history display differs from the vehicle condition (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1. PRECAUTION (w/ Hands Free Power Back Door)

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 58410B 2.REMOVE DECK BOARD ASSEMBLY (for HV Model, w/ Hands Free Power Back Door)

Hide 58416K 3.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model, w/ Hands Free Power Back Door)

Hide 65351A 4.REMOVE BATTERY HOLE COVER (for HV Model, w/ Hands Free Power Back Door)

Hide 5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL (w/ Hands Free Power Back Door)

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



Hide 6.REMOVE REAR BUMPER ASSEMBLY

Hide 89342 7.REMOVE REAR CORNER ULTRASONIC SENSOR

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



a.

Disconnect the connector.

B525589C01
0.104,0.094 0.417,0.333 0.313,0.24 12 false *A 3.521,0.083 3.833,0.333 0.313,0.25 12 false *B
*A w/o Parking Support Brake System *B w/ Parking Support Brake System



b.

Detach the claw and remove the rear corner ultrasonic sensor.

NOTICE:

Before removing the sensor, make sure to mark the sensor and rear bumper assembly so that each sensor can be returned to its original position.


B525250C01
0.104,0.083 0.417,0.333 0.313,0.25 12 false *A 3.583,0.083 3.917,0.333 0.333,0.25 12 false *B
*A w/o Parking Support Brake System *B w/ Parking Support Brake System
V113147

Remove in this Direction - -



Hide 89342A 8.REMOVE REAR CENTER ULTRASONIC SENSOR

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



a.

Disconnect the connector.

B525247C01
0.083,0.094 0.396,0.333 0.313,0.24 12 false *A 3.583,0.083 3.917,0.333 0.333,0.25 12 false *B
*A w/o Parking Support Brake System *B w/ Parking Support Brake System



b.

Detach the claw and remove the rear center ultrasonic sensor.

NOTICE:

Before removing the sensor, make sure to mark the sensor and rear bumper assembly so that each sensor can be returned to its original position.


B525248C01
0.083,0.083 0.396,0.333 0.313,0.25 12 false *A 3.583,0.094 3.917,0.417 0.333,0.323 12 false *B
*A w/o Parking Support Brake System *B w/ Parking Support Brake System
V113147

Remove in this Direction - -



Hide 89348R 9.REMOVE REAR CORNER ULTRASONIC SENSOR RETAINER

HINT:
·

Perform the following procedure only when replacement of a rear corner ultrasonic sensor retainer is necessary.

·

When removing the rear corner ultrasonic sensor retainer, if the double-sided tape is difficult to remove, heat the adhesive of the rear corner ultrasonic sensor retainer and rear bumper cover using a heat light.



a.

Heat the rear bumper assembly and rear corner ultrasonic sensor retainer using a heat light.

CAUTION:
E306500C76
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



Standard:
Item Temperature
Rear Bumper Assembly 40 to 60°C (104 to 140°F)
Rear Corner Ultrasonic Sensor Retainer



b.

Remove the rear corner ultrasonic sensor retainer.

i.

for LH Side:

B525329C01
0.083,0.083 0.417,0.323 0.333,0.24 12 false *A 3.438,0.083 3.75,0.323 0.313,0.24 12 false *B
*A w/o Parking Support Brake System *B w/ Parking Support Brake System



ii.

for RH Side:

B525570C01
0.083,0.083 0.417,0.323 0.333,0.24 12 false *A 3.438,0.083 3.75,0.323 0.313,0.24 12 false *B
*A w/o Parking Support Brake System *B w/ Parking Support Brake System




Hide 89348S 10.REMOVE REAR CENTER ULTRASONIC SENSOR RETAINER

HINT:
·

Perform the following procedure only when replacement of a rear center ultrasonic sensor retainer is necessary.

·

When removing the rear center ultrasonic sensor retainer, if the double-sided tape is difficult to remove, heat the adhesive of the rear center ultrasonic sensor retainer and rear bumper cover using a heat light.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



a.

Heat the rear bumper assembly and rear center ultrasonic sensor retainer using a heat light.

CAUTION:
E306500C76
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



Standard:
Item Temperature
Rear Bumper Assembly 40 to 60°C (104 to 140°F)
Rear Center Ultrasonic Sensor Retainer



b.

Remove the rear center ultrasonic sensor retainer.

B525252C01
0.104,0.083 0.417,0.323 0.313,0.24 12 false *A 3.438,0.094 3.75,0.333 0.313,0.24 12 false *B
*A w/o Parking Support Brake System *B w/ Parking Support Brake System



Hide 89305 11.REMOVE ULTRASONIC SENSOR CUSHION SET (w/ Parking Support Brake System)

HINT:

Only perform this procedure when removing and installing the ultrasonic sensor cushion set.


a.

Remove the ultrasonic sensor cushion set as shown in the illustration.

B549651C02
0,0 0,0 false
V113147

Remove in this Direction - -