Home › Drivetrain › UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE ASSEMBLY › from 2020.08
RM3620E _52 Drivetrain _076122 UB80E AUTOMATIC TRANSMISSION / TRANSAXLE _0370676 AUTOMATIC TRANSAXLE ASSEMBLY A

UB80E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during automatic transaxle assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
ECM Perform Vehicle Identification Number (VIN) or frame number registration DTC P063051 is output w/ Canister Pump Module:(Click here)
w/o Canister Pump Module:(Click here)
ECU communication ID registration Engine start function See Service Bulletin for the registration method.

If transaxle compensation code read from ECM

-

Perform reset memory

-

Transfer transaxle compensation code

-

Perform road test to allow ECM to learn



·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:(Click here)
for Registration:(Click here)

If transaxle compensation code not read from ECM

-

Perform reset memory

-

Transfer transaxle compensation code

-

Perform road test to allow ECM to learn



Gas leaks from exhaust system Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


w/ Canister Pump Module:(Click here)
w/o Canister Pump Module:(Click here)
Engine assembly Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


w/ Canister Pump Module:(Click here)
w/o Canister Pump Module:(Click here)
Perform road test to allow ECM to learn
·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)
Automatic transaxle assembly
·

Perform reset memory

·

Input transaxle compensation code into ECM

·

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:(Click here)
for Registration:(Click here)
Automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Front bumper assembly (Including removal and installation)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for Gasoline model) (Click here)
Front television camera view adjustment Panoramic view monitor system (for Gasoline model) (Click here)
Suspension, tires, etc.
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for Gasoline model) (Click here)
Television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (for Gasoline model) (Click here)
Front wheel alignment adjustment
·

Perform reset memory

·

Perform acceleration sensor zero point calibration and store system information memorization.


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.


CAUTION:
·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.

·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.



PROCEDURE

Hide 1.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Hide 11361J 2.REMOVE FLYWHEEL HOUSING UNDER COVER

Hide 32101A 3.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.
C402749

Turn the crankshaft to gain access to the 6 drive plate and torque converter assembly setting bolts and remove each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.

HINT:

There will be one black-colored drive plate and torque converter assembly setting bolt.



Hide 4.DISCONNECT VACUUM HOSE

a.
C402750

Disconnect the vacuum hose from the rear engine mounting insulator.


b.
C402751

Disconnect the vacuum hose from the vacuum hose connector.


c.

Disengage the 9 clamps to disconnect the vacuum hose from the automatic transaxle assembly.

C402752


Hide 16261G 5.REMOVE FLOW SHUTTING VALVE (NO. 1 WATER BY-PASS HOSE)

Hide 16260 6.DISCONNECT WATER BY-PASS HOSE ASSEMBLY

Hide 35104V 7.REMOVE BREATHER PLUG HOSE

a.
C402754

Disengage the 2 hose clamps to disconnect the breather plug hose.


b.

Using a screwdriver with its tip wrapped with protective tape, remove the breather plug hose from the No. 1 breather plug (ATM).

NOTICE:

Be careful not to damage the No. 1 breather plug (ATM).



c.
C364011C01
1.688,0.438 2.24,0.438 false 1.167,1.396 1.719,1.396 false 1.531,0.375 1.844,0.531 0.313,0.156 10 false *1 1,1.323 1.313,1.479 0.313,0.156 10 false *2
*1 Breather Plug Sub-assembly
*2 Breather Plug Hose


Remove the breather plug sub-assembly from the breather plug hose.

NOTICE:

Be careful not to damage the breather plug sub-assembly.



Hide 45319 8.REMOVE STEERING GEAR HEAT INSULATOR (for LHD)

Hide 9.DISCONNECT WIRE HARNESS (for LHD)

a.
C402755

Disengage the claw, rotate the lever and disconnect the transmission wire connector.


b.
C402756

Disconnect the park/neutral position switch assembly connector.


c.
C402757

Disengage the wire harness clamp and disconnect the vacuum switching valve (for active control engine mount system) connector.


d.

Disconnect the rack and pinion power steering gear assembly connector.

C402758

HINT:

Release the lock before rotating the lock lever.



e.

Remove the 2 bolts to disconnect the wire harness from the rack and pinion power steering gear assembly.


f.

Remove the bolt.

C402759


g.

Disengage the 9 wire harness clamps to disconnect the wire harness.


h.
C402760

Remove the 2 bolts.


i.

Disengage the wire harness clamp to disconnect the wire harness from the automatic transaxle assembly.


Hide 10.DISCONNECT WIRE HARNESS (for RHD)

a.
C402755

Disengage the claw, rotate the lever and disconnect the transmission wire connector.


b.
C402756

Disconnect the park/neutral position switch assembly connector.


c.
C402757

Disengage the wire harness clamp and disconnect the vacuum switching valve (for active control engine mount system) connector.


d.

Disconnect the rack and pinion power steering gear assembly connector.

C403477

HINT:

Release the lock before rotating the lock lever.



e.

Remove the bolt to disconnect the wire harness from the rack and pinion power steering gear assembly.


f.

Remove the bolt.

C407373


g.

Disengage the 8 wire harness clamps to disconnect the wire harness.


h.
C402760

Remove the 2 bolts.


i.

Disengage the wire harness clamp to disconnect the wire harness from the automatic transaxle assembly.


Hide 11363A 11.REMOVE FLYWHEEL HOUSING SIDE COVER

Hide 51100H 15.REMOVE FRONT FRAME ASSEMBLY

Hide 12361 16.REMOVE FRONT ENGINE MOUNTING INSULATOR

a.
C408666

Remove the bolt and front engine mounting insulator from the transverse engine engine mounting bracket.


Hide 12311A 17.REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET

a.
C402764

Remove the 3 bolts and transverse engine engine mounting bracket from the transaxle housing.


Hide 12372A 18.REMOVE ENGINE MOUNTING INSULATOR LH

a.
C402765

Remove the 5 bolts and engine mounting insulator LH from the automatic transaxle case sub-assembly.


Hide 12303 20.REMOVE REAR ENGINE MOUNTING BRACKET SUB-ASSEMBLY

a.
C402766

Remove the 4 bolts and rear engine mounting bracket sub-assembly from the transaxle housing.


Hide 30500 21.REMOVE AUTOMATIC TRANSAXLE ASSEMBLY

a.
C374393

Remove the 8 bolts and automatic transaxle assembly.

NOTICE:

To prevent damage to the knock pins, do not pry between the automatic transaxle assembly and engine assembly.



Hide 32942 22.DISCONNECT OUTLET NO. 1 OIL COOLER HOSE

Hide 32941 23.DISCONNECT INLET NO. 1 OIL COOLER HOSE

Hide 32907C 24.REMOVE NO. 1 OIL COOLER TUBE SUB-ASSEMBLY WITHOUT HOSE

Hide 33493A 25.REMOVE TRANSMISSION OIL COOLER

Hide 33823 26.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C374396

Remove the 2 bolts and No. 1 transmission control cable bracket from the automatic transaxle case sub-assembly.


Hide 35150 27.REMOVE TRANSMISSION CASE PLUG ASSEMBLY

a.
C378105

Remove the transmission case plug assembly from the transaxle housing.


b.

Remove the O-ring from the transmission case plug assembly.


Hide 28.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C374398

Remove the bolt and wire harness clamp bracket from the automatic transaxle case sub-assembly.


b.
C374399

Remove the bolt and wire harness clamp bracket from the automatic transaxle case sub-assembly.


c.
C374400

Remove the 4 bolts and 4 wire harness clamp brackets from the automatic transaxle case sub-assembly and transmission case side cover.


Hide 32000 29.REMOVE TORQUE CONVERTER ASSEMBLY

a.

Remove the torque converter assembly from the automatic transaxle assembly.

NOTICE:

Remove the torque converter assembly from the input shaft horizontally.



Hide 32101 31.INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY