Home › Drivetrain › UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › OIL COOLER › from 2020.08
RM3620E _52 Drivetrain _076123 UB80F AUTOMATIC TRANSMISSION / TRANSAXLE _0370696 OIL COOLER A

UB80F AUTOMATIC TRANSMISSION / TRANSAXLE  OIL COOLER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transmission oil cooler removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
ECM Perform Vehicle Identification Number (VIN) or frame number registration DTC P063051 is output w/ Canister Pump Module:(Click here)
w/o Canister Pump Module:(Click here)
ECU communication ID registration Engine start function See Service Bulletin for the registration method.

If transaxle compensation code read from ECM

-

Perform reset memory

-

Transfer transaxle compensation code

-

Perform road test to allow ECM to learn



·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:(Click here)
for Registration:(Click here)

If transaxle compensation code not read from ECM

-

Perform reset memory

-

Transfer transaxle compensation code

-

Perform road test to allow ECM to learn




NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.


PROCEDURE

Hide 74404B 3.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 53896B 4.REMOVE FRONT FENDER FRONT SPLASH SHIELD LH

Hide 53895B 5.REMOVE FRONT FENDER FRONT SPLASH SHIELD RH

Hide 51441 6.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51420 7.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

Hide 53737D 8.REMOVE FRONT FENDER APRON SEAL LH

Hide 9.DRAIN ENGINE COOLANT

Hide 32942 11.DISCONNECT OUTLET NO. 1 OIL COOLER HOSE

a.
C402668

Slide the clip and disconnect the outlet No. 1 oil cooler hose from the oil cooler union sub-assembly.

HINT:

Use a container to catch any automatic transaxle fluid which flows out of the outlet No. 1 oil cooler hose and oil cooler union sub-assembly.



Hide 32941 12.DISCONNECT INLET NO. 1 OIL COOLER HOSE

a.
C402669

Slide the clip and disconnect the inlet No. 1 oil cooler hose from the No. 1 oil cooler outlet tube sub-assembly.

HINT:

Use a container to catch any automatic transaxle fluid which flows out of the inlet No. 1 oil cooler hose and No. 1 oil cooler outlet tube sub-assembly.



Hide 32907C 13.REMOVE NO. 1 OIL COOLER TUBE SUB-ASSEMBLY WITHOUT HOSE

a.
C402670

Remove the 2 bolts to disconnect the No. 1 oil cooler tube sub-assembly without hose from the automatic transaxle case sub-assembly.


b.
C420138

Slide the clip and disconnect the inlet No. 2 oil cooler hose from the transmission oil cooler.

HINT:

Use a container to catch any automatic transaxle fluid which flows out of the inlet No. 2 oil cooler hose and transmission oil cooler.



c.
C420139

Slide the clip and disconnect the outlet No. 2 oil cooler hose to remove the No. 1 oil cooler tube sub-assembly without hose from the transmission oil cooler.

HINT:

Use a container to catch any automatic transaxle fluid which flows out of the outlet No. 2 oil cooler hose and transmission oil cooler.



d.
C402673C01
1.833,0.667 1.833,0.333 1.833,0.333 2,0.333 false 2.792,0.604 2.917,0.167 2.917,0.167 3.083,0.167 false 0.417,1.75 0.25,1.75 0.25,1.75 0.25,1.406 false 3.083,1.25 2.917,1.25 2.917,1.25 2.833,1 false 1.833,1.917 1.667,1.917 1.667,1.917 1.365,1.667 false 2.042,0.25 2.208,0.417 0.167,0.167 10 false *1 1.875,1.833 2.042,2 0.167,0.167 10 false *2 3.125,0.083 3.292,0.25 0.167,0.167 10 false *3 0.458,1.667 0.625,1.833 0.167,0.167 10 false *4 3.125,1.167 3.292,1.333 0.167,0.167 10 false *5
*1 No. 1 Oil Cooler Tube Sub-assembly without Hose
*2 Inlet No. 1 Oil Cooler Hose
*3 Inlet No. 2 Oil Cooler Hose
*4 Outlet No. 1 Oil Cooler Hose
*5 Outlet No. 2 Oil Cooler Hose


Slide the 4 clips and remove the inlet No. 1 oil cooler hose, inlet No. 2 oil cooler hose, outlet No. 1 oil cooler hose and outlet No. 2 oil cooler hose from the No. 1 oil cooler tube sub-assembly without hose.


Hide 16261G 14.DISCONNECT NO. 1 WATER BY-PASS HOSE

a.
C402674

Disengage the 3 clamps to remove the transmission breather clamp.


b.
C420140

Slide the clip and disconnect the No. 1 water by-pass hose from the transmission oil cooler.

HINT:

Use a container to catch any coolant which flows out of the No. 1 water by-pass hose and transmission oil cooler.



Hide 16260 15.DISCONNECT WATER BY-PASS HOSE ASSEMBLY

a.
C420141

Slide the clip and disconnect the water by-pass hose assembly from the transmission oil cooler.

HINT:

Use a container to catch any coolant which flows out of the water by-pass hose assembly and transmission oil cooler.



Hide 33493A 16.REMOVE TRANSMISSION OIL COOLER

a.
C420142

Remove the 3 bolts and the transmission oil cooler from the automatic transaxle case sub-assembly.