Home › Drivetrain › GF2A (TRANSFER / 4WD / AWD) › TRANSFER CASE FRONT OIL SEAL (for LH Side) › from 2020.08
RM3620E _52 Drivetrain _077125 GF2A TRANSFER / 4WD / AWD _0375693 TRANSFER CASE FRONT OIL SEAL(for LH Side) A

GF2A TRANSFER / 4WD / AWD  TRANSFER CASE FRONT OIL SEAL(for LH Side)  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the transfer case front oil seal removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system for A25A-FKS:(Click here)
for M20A-FKS:(Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Reset back door close position Power back door system (Click here)
Power back door initialization Power door lock control system (Click here)
for UB80F:

Automatic transaxle assembly


·

Perform reset memory

·

Input transaxle compensation code into ECM

·

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:(Click here)
for Registration:(Click here)
Automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
for K120F:

Continuously variable transaxle assembly


Air bleed oil pump with motor assembly (w/ Stop and Start System) Stop and start system (Click here)
·

Input transaxle compensation code into TCM

·

Perform reset memory

·

Deceleration sensor zero point calibration

·

CVT oil pressure calibration

·

Perform road test to allow TCM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:(Click here)
for Registration:(Click here)
CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Air bleed oil pump with motor assembly (w/ Stop and Start System) Stop and start system (Click here)
Front 4WD linear solenoid (transfer assembly)
·

ECU Data Initialization

·

Disconnect System Function Check


Dynamic torque vectoring AWD system (Click here)
Front wheel alignment adjustment
·

Perform reset memory

·

Perform acceleration sensor zero point calibration and store system information memorization.


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (Click here)
Perform headlight ECU sub-assembly LH initialization Lighting System (EXT) (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.


CAUTION:
·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.


·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·
C313282C01
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Transmission Jack


The automatic transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop.



PROCEDURE

Hide 36100 1.REMOVE TRANSFER ASSEMBLY

Hide 36100A 2.REMOVE TRANSFER AND TRANSAXLE SETTING STUD BOLT

Hide 36111B 4.REMOVE TRANSFER CASE OIL SEAL

a.
C405119C01
0.688,1.26 1.01,1.135 true 2,1.76 2,1.406 true 1.885,1.854 2.344,2.052 0.458,0.198 10 false SST 0.479,1.177 0.792,1.375 0.313,0.198 10 false *1
*1 Transfer Case Oil Seal


Using SST, remove the transfer case oil seal from the transfer case.

SST
09308-00010  

NOTICE:
·

Do not scratch the press-fitting surface of the transfer case oil seal.

·

Wear or damage to the front drive shaft oil seal RH on the transmission side will cause transfer oil leakage.

If it is worn or damaged, replace the front drive shaft oil seal RH.

for Automatic Transaxle:

Click hereDrivetrain>UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>DIFFERENTIAL OIL SEAL (for RH Side)>REPLACEMENT

for CVT:

Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>FRONT DIFFERENTIAL OIL SEAL (for RH Side)>REPLACEMENT




Hide 36111B 5.INSTALL TRANSFER CASE OIL SEAL

a.

Coat the lip of a new transfer case oil seal with MP grease.


b.
C405120C01
0.719,3.938 1.385,3.438 true 0.917,0.75 1.083,0.75 1.083,0.75 1.531,1.344 true 1.083,0.75 1.469,1.521 true 0.531,3.833 0.844,3.99 0.313,0.156 10 false *1 0.573,0.667 0.969,0.833 0.396,0.167 10 false SST 0.635,2.99 1.094,3.188 0.458,0.198 10 false (A)
*1 Transfer Case Oil Seal


Using SST and a hammer, tap in a new transfer case oil seal as shown in the illustration.

SST
09608-10010  
09950-70010  (09951-07100)

Drive in depth (A):

9.5 to 10.5 mm (0.375 to 0.413 in.)


NOTICE:
·

Tap the transfer case oil seal uniformly so that the transfer case oil seal is straight.

·

Do not tap the transfer case oil seal in too far.




Hide 36100 6.REMOVE TRANSFER ASSEMBLY

Hide 36100A 7.INSTALL TRANSFER AND TRANSAXLE SETTING STUD BOLT

Hide 36100 8.INSTALL TRANSFER ASSEMBLY