Home › Suspension › FRONT SUSPENSION › FRONT SUSPENSION MEMBER (for Gasoline Model) › from 2020.08
RM3620E _53 Suspension _076490 FRONT SUSPENSION _0372231 FRONT SUSPENSION MEMBER(for Gasoline Model) A

FRONT SUSPENSION  FRONT SUSPENSION MEMBER(for Gasoline Model)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front frame assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

*2: w/ Gasoline Particulate Filter

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system for A25A-FKS:(Click here)
for M20A-FKS:(Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
ECM Perform Vehicle Identification Number (VIN) or frame number registration DTC P063051 is output A25A-FKS (w/ Canister Pump Module):(Click here)
A25A-FKS (w/o Canister Pump Module):(Click here)
M20A-FKS:(Click here)
ECU communication ID registration Engine start function See Service Bulletin for the registration method.
for M20A-FKS:

GPF Deposition Values*2

-

GPF deposition values save

-

GPF deposition values write



·

MIL comes on

·

Deterioration of fuel efficiency


(Click here)
for UB80E:

If transaxle compensation code read from ECM

-

Perform reset memory

-

Transfer transaxle compensation code

-

Perform road test to allow ECM to learn



·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:(Click here)
for Registration:(Click here)
for UB80F:

If transaxle compensation code read from ECM

-

Perform reset memory

-

Transfer transaxle compensation code

-

Perform road test to allow ECM to learn



·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:(Click here)
for Registration:(Click here)
for K120:
·

Perform reset memory

·

Perform road test to allow TCM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)
for K120F:
·

Perform reset memory

·

Perform road test to allow TCM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)
·

Gas leak from exhaust system is repaired

·

Replacement of air fuel ratio sensor


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


A25A-FKS (w/ Canister Pump Module):(Click here)
A25A-FKS (w/o Canister Pump Module):(Click here)
M20A-FKS:(Click here)
for M20A-FKS:

Front exhaust pipe assembly


GPF deposition value clear
·

MIL comes on

·

Deterioration of fuel efficiency


(Click here)
Automatic transaxle assembly
for UB80E:
·

Reset memory

·

Input transaxle compensation code into ECM

·

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:(Click here)
for Registration:(Click here)
for UB80F:
·

Reset memory

·

Input transaxle compensation code into ECM

·

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:(Click here)
for Registration:(Click here)
Automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly for UB80E:(Click here)
for UB80F:(Click here)
Continuously variable transaxle assembly
for K120:
·

Input transaxle compensation code into TCM

·

Perform reset memory

·

Deceleration sensor zero point calibration

·

CVT oil pressure calibration

·

Perform road test to allow TCM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:(Click here)
for Registration:(Click here)
for K120F:
·

Input transaxle compensation code into TCM

·

Perform reset memory

·

Deceleration sensor zero point calibration

·

CVT oil pressure calibration

·

Perform road test to allow TCM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:(Click here)
for Registration:(Click here)
CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly for K120:(Click here)
for K120F:(Click here)
Air bleed oil pump with motor assembly (w/ Stop and Start System) Stop and start system (Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (for Gasoline model) (Click here)
Television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (for Gasoline model) (Click here)
Perform headlight ECU sub-assembly LH initialization Lighting System (EXT) (Click here)
Front wheel alignment adjustment
·

Perform reset memory

·

Perform acceleration sensor zero point calibration and store system information memorization.


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Front bumper assembly (Including removal and installation)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for Gasoline model) (Click here)
Front television camera view adjustment Panoramic view monitor system (for Gasoline model) (Click here)
Rack and pinion power steering gear assembly
·

Perform torque sensor zero point calibration

·

Assist map writing


·

DTCs are output

·

EPS warning light illuminates


(Click here)

NOTICE:
·

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.

·

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



PROCEDURE

Hide 45319 4.REMOVE STEERING GEAR HEAT INSULATOR (for LHD)

Hide 5.DISCONNECT WIRE HARNESS

Hide 51100H 6.REMOVE FRONT FRAME ASSEMBLY (for 2WD)

a.
C406800

Remove the 3 nuts and separate the front engine mounting insulator from the front frame assembly.


b.

for Automatic Transaxle and CVT:

i.
C406801

Remove the 4 nuts and separate the rear engine mounting insulator from the front frame assembly.



c.

for Manual Transaxle:

i.
C406803

Remove the 4 nuts and separate the rear engine mounting insulator from the front frame assembly.



Hide 51100H 7.REMOVE FRONT FRAME ASSEMBLY (for 4WD/AWD)

a.
C406800

Remove the 3 nuts and separate the front engine mounting insulator from the front frame assembly.


b.
C406802

Remove the 4 nuts and separate the rear engine mounting insulator from the front frame assembly.


Hide 8.REMOVE FRONT STABILIZER BAR WITH BRACKET

Hide 44250 9.REMOVE RACK AND PINION POWER STEERING GEAR ASSEMBLY

Hide 48069 10.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.
C403175

Remove the 3 bolts, nut and front lower No. 1 suspension arm sub-assembly LH from the front frame assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



b.

Remove the front lower arm bushing stopper from the front lower No. 1 suspension arm sub-assembly.


Hide 48068 11.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 17572B 12.REMOVE NO. 2 EXHAUST PIPE SUPPORT BRACKET

a.
C403176

Remove the 2 bolts and No. 2 exhaust pipe support bracket from the front frame assembly.