CRUISE CONTROL SYSTEM > Cruise Control Switch Circuit |

| 1.READ VALUE USING TECHSTREAM (CRUISE CONTROL MAIN SWITCH) |
![]() |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Cruise Control / Data List.
Check the Data List for proper functioning of the cruise control main switch.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| CCS Main SW M-CPU | Main switch signal (Main CPU)/ON or OFF | ON: Main switch on OFF: Main switch off | - |
| Cancel Switch | CANCEL switch signal/ON or OFF | ON: CANCEL switch on OFF: CANCEL switch off | - |
| SET/COAST Switch | SET/COAST switch signal/ON or OFF | ON: - (COAST)/SET switch on OFF: - (COAST)/SET switch off | - |
| RES/ACC Switch | RES/ACC switch signal/ON or OFF | ON: + (ACCEL)/RES (RESUME) switch on OFF: + (ACCEL)/RES (RESUME) switch off | - |
| Result | Proceed to |
| OK | A |
| NG (All items are defective) | B |
| NG (1 to 3 items are defective) | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 2.INSPECT CRUISE CONTROL MAIN SWITCH |
Remove the cruise control main switch (Click here).
Measure the resistance according to the value(s) in the table below.

| Tester Connection | Switch Condition | Specified Condition |
| A-3 (CCS) - A-1 (ECC) | Neutral | 10 kΩ or higher |
| A-3 (CCS) - A-1 (ECC) | + (ACCEL)/RES (RESUME) | 235 to 245 Ω |
| A-3 (CCS) - A-1 (ECC) | - (COAST)/SET | 620 to 640 Ω |
| A-3 (CCS) - A-1 (ECC) | CANCEL | 1510 to 1570 Ω |
| A-3 (CCS) - A-1 (ECC) | Main switch on | Below 1 Ω |
Reinstall the cruise control main switch.
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (CRUISE CONTROL MAIN SWITCH - SPIRAL CABLE) |
![]() |
Disconnect the z11 connector from the spiral cable.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A-3 - z11-3 | Always | Below 1 Ω |
| A-1 - z11-4 | Always | Below 1 Ω |
Reconnect the spiral cable connector.
|
| ||||
| OK | |
| 4.INSPECT SPIRAL CABLE |
![]() |
Remove the spiral cable.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Spiral Cable Position | Specified Condition |
| z11-3 (CCS) - H54-1 (CCS) | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| z11-4 (ECC) - H54-2 (ECC) | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right |
Reinstall the spiral cable.
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - ECM AND BODY GROUND) |
![]() |
Disconnect the A27 connector from the ECM.
Disconnect the H54 connector from the spiral cable.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H54-1 (CCS) - A27-45 (CCS) | Always | Below 1 Ω |
| A27-45 (CCS) - Body ground | Always | 10 kΩ or higher |
| H54-2 (ECC) - Body ground | Always | Below 1 Ω |
Reconnect the ECM and spiral cable connector.
| Result | Proceed to |
| NG | A |
| OK (for 2UZ-FE) | B |
| OK (for 3UR-FE) | C |
| OK (for 3UR-FBE) | D |
|
| ||||
|
| ||||
|
| ||||
| A | ||
| ||