Home › Engine / Hybrid System · 2UZ-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P1340    Camshaft Position Sensor "A" (Bank 1 Sensor 2)

DTC    P1342    Camshaft Position Sensor "A" Low Input (MRE)

DTC    P1343    Camshaft Position Sensor "A" High Input (MRE)

for Preparation Click here


DESCRIPTION

The camshaft has a timing rotor for the camshaft position sensor. When the camshaft rotates, changes occur in the air gaps between the timing rotor and MRE element, which affects the magnet. As a result, the resistance of the MRE material fluctuates. The camshaft position sensor converts the camshaft rotation data to pulse signals, and uses the pulse signals to determine the camshaft angle, which it sends to the ECM. Then the ECM uses this data to control fuel injection time and injection timing.

DTC No.
DTC Detection Condition
Trouble Area
P1340
No camshaft position sensor signal to ECM during cranking (2 trip detection logic)
  1. Open or short in camshaft position sensor circuit
  2. Camshaft position sensor
  3. Camshaft timing pulley LH
  4. ECM
No camshaft position sensor signal to ECM with engine speed 600 rpm or more
(1 trip detection logic)
P1342
Output voltage of camshaft position sensor less than 0.3 V for 4 seconds
(1 trip detection logic)
P1343
Output voltage of camshaft position sensor more than 4.7 V for 4 seconds
(1 trip detection logic)

MONITOR DESCRIPTION

If there is no signal from the camshaft position sensor even though the engine is turning, or if the rotation of the camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor. When the sensor output voltage remains less than 0.3 V, or more than 4.7 V for more than 5 seconds, the ECM sets a DTC.

MONITOR STRATEGY


Related DTCs
P1340: Camshaft position sensor range check
P1340: Camshaft position / Crankshaft position misalignment
P1342: Camshaft position sensor range check (low voltage)
P1343: Camshaft position sensor range check (high voltage)
Required Sensors/Components (Main)
Camshaft position sensor
Required Sensors/Components (Related)
Crankshaft position sensor, Engine speed sensor
Frequency of Operation
Continuous
Duration
5 seconds: P1340 camshaft position / crankshaft position misalignment
4 seconds: P1340, P1342 and P1343 camshaft position sensor range check
MIL Operation
2 driving cycles: P1340 camshaft position sensor range check
Immediate: P1340 camshaft position / crankshaft position misalignment and P1342, P1343 camshaft position sensor range check
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever these DTCs are not present
None

P1340 Camshaft Position Sensor Range Check 
Starter
ON
Minimum battery voltage while starter ON
Less than 11 V

P1340 Camshaft Position / Crankshaft Position Misalignment 
Engine RPM
600 rpm or more
Starter
OFF
Camshaft position sensor voltage
0.3 V or more, 4.7 V or less

P1342, P1343 Camshaft Position Sensor Range Check 
Time after ignition switch off to ON
2 seconds or more
Battery voltage
8 V or more
Starter
OFF

TYPICAL MALFUNCTION THRESHOLDS


P1340 Camshaft Position Sensor Range Check 
Camshaft position signal
No signal

P1340 Camshaft Position / Crankshaft Position Misalignment 
Camshaft position and crankshaft position phase
Misaligned
Camshaft position signal
No signal

P1342 Camshaft Position Sensor Range Check 
Camshaft position sensor voltage
Less than 0.3 V

P1343 Camshaft Position Sensor Range Check 
Camshaft position sensor voltage
More than 4.7 V

COMPONENT OPERATING RANGE


Camshaft position sensor voltage
0.3 to 4.7 V

WIRING DIAGRAM


A185020E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.INSPECT CAMSHAFT POSITION SENSOR (SENSOR POWER SOURCE)
A160975E03
  1. Disconnect the camshaft position sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D59-3 (VC) - Body ground
    Ignition switch ON
    4.5 to 5.0 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK HARNESS AND CONNECTOR (ECM - CAMSHAFT POSITION SENSOR)
A160974E04
  1. Disconnect the camshaft position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D59-2 (G2) - D56-90 (G2)
    Always
    Below 1 Ω
    D59-1 (G-) - D56-89 (G2-)
    Always
    Below 1 Ω
    D59-2 (G2) or D56-90 (G2) - Body ground
    Always
    10 kΩ or higher
    D59-1 (G-) or D56-89 (G2-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT SENSOR INSTALLATION
BR03795E62
  1. Check the camshaft position sensor installation.

    OK:
    The camshaft position sensor is installed properly.



NG
SECURELY REINSTALL SENSOR (Click here)
OK


4.INSPECT CAMSHAFT TIMING PULLEY LH (SIGNAL PLATE TEETH)
  1. Check the teeth of the signal plate.

    OK:
    Sensor plate teeth do not have any cracks or deformation.



NG
REPLACE CAMSHAFT TIMING PULLEY LH (Click here)
OK


5.REPLACE CAMSHAFT POSITION SENSOR
  1. Replace the camshaft position sensor (Click here).


NEXT


6.CONFIRM WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream ON.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    No DTC is output
    A
    P1340, P1342 and/or P1343 are output
    B

    HINT:
    If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

END